Vannus i6-5B-40 LED Ceiling Fan Instruction Manual

Vannus i6-5B-40 LED Ceiling Fan

INSTRUCTION MANUAL

Version: 2022 V1

MODEL

i6 – 5B/40 LED i6 – 5B/56 LED

CEILING FAN

Table of Contents

• 1. Safety Precaution
• 2. Parts & Accessories
• 3. Installation Instruction
• 4. Power Supply Connection
• 5. Circuit Diagram
• 6. Transmitter Learning Process
• 7. Transmitter Function & Assembly
• 8. Maintenance
• 9. Technical Specifications
• 10. Customer Service Centre

Safety Precaution

Warning

• Installation and maintenance work shall only be performed by qualified persons, familiar with local code and regulation, and experienced with this type of appliance.
• All field wiring must be installed in accordance with the national wiring regulation.
• Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing wiring work according to the wiring diagram.
• The appliance must be permanently connected to the electricity supply through a double pole switch having a contact separation of at least 3mm in all poles.
• The unit must be GROUNDED to prevent possible hazard due to insulation failure. The earth wire is approximately 60mm longer than safety wire. This is to ensure at the event whereby the suspension system fails, the (L) and (N) wire will break leaving the fan remain earthed to prevent electrocution.
• Tighten the blade firmly using a screwdriver. Blades that are detached from the unit during operation will cause serious injuries and property damages.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliances.
• Confirm that the power supply has been switched OFF before installing or servicing the unit. Ensure that the blade is fully static before doing any maintenance work.

CAUTION

Please take note of the following important points when installing.

• The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with sufficient strength to withstand 4 times the weight of the ceiling fan.
• The mounting of the suspension system shall be performed by the manufacturer, its service agent, or suitably qualified persons.
• The fan is to be installed so that the blades are more than 2.5m above the floor.
• The safety cord should not be longer than the earthing conductor. Should the failure of the suspension system occur, the support of the fan must not rely on the earthing conductor. The earthing terminal in the fan assembly should be such that should any part of the suspension system fall off, the body of the fan assembly shall be effectively earthed.
• Ensure that the unit’s panel is closed after service or installation. Unsecured panels will cause the unit to operate noisily.

Safety Precaution

Warning

• Installation and maintenance work shall only be performed by qualified persons, familiar with local code and regulations, and experienced with this type of appliance.
• All field wiring must be installed in accordance with the national wiring regulation.
• Ensure that the rated voltage of the unit corresponds to that of the nameplate before commencing wiring work according to the wiring diagram.
• The appliance must be permanently connected to the electricity supply through a double pole switch having a contact separation of at least 3mm in all poles.
• The unit must be GROUNDED to prevent possible hazards due to insulation failure.
• The earth wire is approximately 60mm longer than the safety wire. This is to ensure at the event whereby the suspension system fails, the (L) and (N) wires will break leaving the fan to remain earthed to prevent electrocution.
• Tighten the blade firmly using a screwdriver.
• Blades that are detached from the unit during operation will cause serious injuries and property damage.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliances.
• Confirm that the power supply has been switched OFF before installing or servicing the unit. Ensure that the blade is fully static before doing any maintenance work.

STOP using the ceiling fan when an

abnormality or failure occurs.
If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.
CAUTION
Please take note of the following important points when installing.

• The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with sufficient strength to withstand 4 times the weight of the ceiling fan.
• The mounting of the suspension system shall be performed by the manufacturer, its service agent, or suitably qualified persons.
• The fan is to be installed so that the blades are more than 2.5m above the floor.
• The safety cord should not be longer than the earthing conductor.
• Should the failure of the suspension system occur, the support of the fan must not rely on the earthing conductor. The earthing terminal in the fan assembly should be such that should any part of the suspension system fall off, the body of the fan assembly shall be effectively earthed.
• Ensure that the unit’s panel is closed after service or installation.
• Unsecured panels will cause the unit to operate noisily.
• Sharp edges and coil surfaces are potential locations that may cause injury hazards. Avoid being in contact with these places.
• Before turning off the power supply set the remote controller’s ON/OFF switch to the “OFF” position.
• If this is not done, the unit’s fans will start turning automatically when power resumes, posing a hazard to service personnel or the user.
• Do not operate any heating apparatus too close to the ceiling fan unit or use it in a room where mineral oil, oil vapor, or oil steam exists, this may cause the plastic part to melt or deform as a result of excessive heat or chemical reaction.
• Ensure the color of the wires of the outdoor unit and the terminal markings are the same as the indoors respectively.
• Don’t use joined and twisted wires for incoming power supply.
• Do not place any object in the path of the blades. Avoid raising objects or your arms near the ceiling fan.
• The fan suspension system and blade screw tightening shall be examined yearly.
• Replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent, or suitably qualified persons.
• The torque value for screws/bolts for securing the primary suspension system for the motor is 2Nm.

Parts & Accessories

Installation Instruction

IMPORTANT: DO NOT CONNECT THIS REMOTE CONTROL CEILING FAN TO THE DIMMER SWITCH OR REGULATOR.

1. Step 1 –

   • Route all the wire from the motor through the downrod. Fix the downrod to the coupling with bolt, washer, and nut and tighten them firmly then insert the clevis pin.
   • Assemble the coupling cover and the canopy through the downrod.

2. Step 2 –
   Remove the Bolt, Clevis, Nut, Washer, and Rubber Pulley from the Downrod.
   Place the Rubber Pulley onto the ceiling hook and fix back the Bolt, Clevis, Nut, and Washer.
   IMPORTANT: Clevis Pin MUST be inserted to prevent the nut from loosening.

3. Step 3 – Remove the Safety Wire screw and spring washer from the Downrod.

4. Step 4 – Tie the Safety Wire across the hook as shown

5. Step 5 – Firmly screw the Safety Wire with the spring washer onto the Downrod.

6. Step 6 – Connect the Connectors from Fan and Receiver. Connect the wires from the receiver to House’s Supply Wire. Connect Earth Wire to House Supply Earth Terminal.

7. Step 7 – Install the Blades on the Motor with Blade Screw. Install the Switch Housing by twisting it in.
   IMPORTANT: Assemble the Fan Blades only after the ceiling fan is mounted on the hook.

Below shows a complete installation diagram.

Power Supply Connection

IMPORTANT: DO NOT CONNECT THIS REMOTE CONTROL CEILING FAN TO THE DIMMER SWITCH OR REGULATOR.

Circuit Diagram

Transmitter Learning Process

The receiver & transmitter is pre-programmed in the factory. If you wish to control 2 or more fans using 1 transmitter, the below steps are required.
DO NOT PRESS ANY OTHER BUTTON DURING THIS PROCESS
Step 1

1. Insert the 2 pcs of batteries (provided) into the transmitter.
2. Turn on the power supply (wall switch) to the fan.
3. Within 10 sec, press and hold the “1” and “2” buttons for 3 sec. Once the receiver has detected the frequency, the transmitter will “Beep Beep” twice. The programming process is completed and fan is ready to use.
   If the fan is not responding to the transmitter, repeat Step 1b.

Transmitter Function

• 1 – 8- Fan speed control
• – Natural wind, creating a gentle sea-breeze effect
• – Forward/Reverse, turn anti-clockwise or clockwise rotation.
• – Stop the fan
• – Ligh on/off and select LED color
• 1H- Fan turn on after 1hr
• 3H- Fan turn on after 3hr
• 6H- Fan turn on after 6hr

The transmitter & receiver is incorporated with the last memory function. This function stores your last setting in memory and the next time you turn on the fan, fan will operate as the last setting.

The function of Forward & Reverse

The fan must be turned on and rotating. Press the Forward/Reverse button and the fan will slow down and then change direction (approx. 15 sec). When the fan is slowing down to change direction, the Fan Speed function is disabled until the direction has been changed.

• Forward
  Fan rotates anti-clockwise blowing the air downwards creating the wind chill effect. Suitable for hot weather conditions.

• Reverse
  Fan rotates clockwise drawing the air towards the ceiling and circulating the warm air downwards. This function works best at low speed. Suitable for air- conditioned conditions.

Maintenance

Due to the fan’s natural movement, connections may get loose after a period of usage. To ensure proper and safe usage, it is highly recommended to inspect and tighten all connections every 6 months.

Cleaning

Cleaning your fan periodically will prolong its new appearance. Basic cleaning procedures are as follows :

1. Use only water and mild soap. Do not use solvents, corrosive or acidic solutions.
2. Damp the cloth lightly. Use only soft or lint-free cloth to clean the fan. Rough fabric will scratch the surface.
3. Do not bent the blades while cleaning. At the event that blades are bent or damaged, order a new set of blades from service center or dealer shop.
4. There is no need to oil the fan.

Technical Specifications

Customer Service Centre

If you need any technical assistance or faulty report, please contact our customer service centre at :

• Alpha Home Appliances Sdn. Bhd. (390258-H)
• Head Office : 6, Jalan Sungai Kayu 32/37, Berjaya Park, Sect 32, 40460 Shah Alam, Selangor
• Tel : 03-5740 6666 Fax : 03-5740 8220
• Website : www.alphamalaysia.com Email : info@alphamalaysia.com
• Johor : 71, Jalan Molek 3/10, Taman Molek, 81100 Johor Bahru.
• Tel : 07-353 4833 / 4933 Fax : 07-355 4233
• Melaka : 19, 19-1 & 19-2, Jalan KSB 11, Taman Kota Syahbandar, 75200 Melaka.
• Tel : 06-292 6292 / 6293 Fax : 06-292 6296
• Perak : 11, Laluan Tasek Timur 5, 31400 Ipoh, Perak.
• Tel : 05-545 2282 / 547 2282 Fax : 05-547 6282
• Penang : 28, Jalan Icon City, Icon City, 14000 Bukit Mertajam, Penang.
• Tel : 04-506 2366 / 2066 / 2566 Fax : 04-506 2966
• Pahang : A131, Jalan Dato Wong Ah Jang, Taman Liza, 25100 Kuantan, Pahang.
• Tel : 09-516 5226 Fax : 09-513 9226

References

• Home | Alpha Home Appliances Sdn Bhd

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>