RONIN 140528 Remote Control Instructions

June 13, 2024
RONIN

RONIN logo 140528 Remote Control
InstructionsRONIN 140528 Remote Control Ronin Remote P/N 140528

Remote Controller Specification:

  1. 2.4GHz bidirectional communication, 3 channels, automatic frequency modulation and anti-interference.
  2.  32bit ID code, extremely low probability of duplicate codes
  3. Built in lithium battery, USB port for charging.
  4. Accelerator and braking functions
  5. Remote control and receiver disconnection reminder function, automatically shuts down after 5 minutes of disconnection, saving power.
  6. The code memory function allows for quick connection between the remote control and receiver during use.
  7. When the receiver loses contact with the remote controller, turn off the accelerator, and the Electric Speed Controller adjusted into an emergency state to protect the user.

Remote Controller Technical Parameters

NO ITEM SPECIFICATION REMARK
1 Transmitting power 2dBm
2 Operating Frequency 2400 to 2483MHz Error±10ppm
3 Working Current Average 60mA, peak 235mA @3.7V
4 ShutDown Current <1uA
5 Operation Time 10hours
6 Communication Distance >80M Open ground without WIFI interference
7 Battery Capacity 420mAH 3.7V Capacity Error+30%, -10% @ 0.2C discharge

rate
8| Charging input current| 180 to 230mA|
9| Charging Time| 3hours| Automatic stop when the battery is fully charged

Receiver Technical Parameters

1| Transmitting Power| 20dBm|
---|---|---|---
2| Operating Frequency| 2400 to 2483MHz| Error±10ppm
3| Working Current| Average 60mA, peak 235mA| @5V
4| Working Voltage| Battery Side 1S to 2S| Electric Speed Controller side 3.8V to 12V
**** 5| Throttle PWM pulse width| Maximum braking=1000us, Midpoint=1500us, Maximum throttle=2000us| Error 30ppm
6| Directional PWM pulse width| Forward=2000us, Reverse=1000us
7| Start time of disconnected throttle closing| 750ms|
8| UART Throttle| Bauds=115200, Benjamin VESC Control Protocol|
9| SW1 (MOS)| Withload 12V, 1A| Max Voltage<20V, Peak Current<3A
10| Motor phase line  speed measurement| Max 75960 erpm|

Pin voltage, refer to PCB bottom screen printing

HALL: Input pin, connected to motor Hall, for speed measurement, high level 3.3 to 5V.
RXD: Input pin, receiver UART RXD
TXD: Output pin, receiver UART TXD
PWM_R: Output pin, PWM reserved pin
PWM_T: reserve
5V: Input pin, power supply 3.8 to 12V from the Electric Speed Controller.
GND: Ground
SW1: reserve
BAT: Input pin, Electric Speed Controller battery side voltage,2S to 20SRONIN 140528 Remote Control - Fig

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference  that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there  is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
The devices has been evaluated to meet general RF exposure requirement, the device can be used in portable exposure condition without restrictionRONIN
logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals