RONIN RavenEye Image Transmitter System User Manual

June 3, 2024
RONIN

RONIN RavenEye Image Transmitter System

RONIN-RavenEye-Image-Transmitter-PRODUCT

Specifications

  • Operating frequency: FCC: 2412-2452MH2, 5180-52401MH2.5745-5825MHz. ISED 2412-2462MH2, 5745-5825MHz CE 2412-2472MHz, 5745-5825MHz 3
  • Weight: 126g
  • Dimensions: 82mm x 63mm x 24mm
  • Transmitter power (EIRP): 2.4 GHz: <25 dBm (FCC), < 20 dBm (CE/SRRCAMIC); 5.1 GHz: < 25 dBm (FCC), < 20 dBm (KCO) 5.8 GHz: < 25 dBm (FCC/SRRC), < 14 dBm (CE)
  • Operating time: Approx.3.5 hours See http://www.dj.com/service for after-sales support for your product, as applicable.
    • DJI OSMO means. DJI OSMO TECHNOLOGY co., LTD. and/or its affiliated companies, as applicable.

Disclaimer and Notice

Parabens for having acquired your new product L SMO Lena with this OClmento for interior and all the safe and legal practices 1onecicials by DiOSMO before use. Failure to read and comply with instructions and warnings may result in serious injury to you or third parties, damage to your DJI OSMO product, OR damage to other objects in the vicinity. By using this product, you confirm that you have read this document carefully and that you understand and agree to be bound by all terms and conditions of this document and all documents relevant to this product. You agree to use this product only for its proper purposes. You agree that you are solely responsible for your conduct during the use of this product and the possible consequences resulting therefrom.

DJI OSMO assumes no responsibility for the damages, injuries or any legal liability arising directly or indirectly from the use of this product. RONIN is a trademark of SZ DJI OSMO TECHNOLOGY CO., LTD. abbreviated as “DJI OSMO) and the respective affiliated companies. of products, brands, etc. appearing in this document are trademarks or registered trademarks of their respective companies. This product and document are protected by Dl OSMO with all rights reserved. No part of this product or document should be reproduced in any form without prior written consent or authorization from DJI Osmo. This and all other related documents are subject to change at DJI OSMO’s sole discretion. For up-to-date information about the product, visit http://wwww.di.com and click on the product page related to this product. This document is available in several languages. In case of divergence between different versions, the English version will prevail.

Use

Download the corresponding User Guide for accessories via the link below. Make sure you completely read and understand this document. before use. http://www.dji.com/rs-2/downloads

FCC Compliance Notice

Supplier’s Declaration of Conformity
  • Product name: Ronin RavenEye Image Transmission System
  • Model Number: V-002
  • Responsible Party: DJI Technology, Inc.
  • Responsible Party Address: 201 S. Victory Blvd., Burbark, CA 91502
  • Website: www.dji.com

We, DJI Technology, Inc., being the responsible party, declare that the above- mentioned model was tested to demonstrate compliance with all applicable rCC rules and regulations.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interterence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

  • Reorient or relocate lhe receiving antenna.
  • Increase the separation between the cquipmcnt and receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions for satisfying RF exp0sure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by lhe Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

ISED Compliance Notice: This device contains license-exempt transmitter (s/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(S).

Operation is subject to tho following two conditions

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may causes undesired operation of the device.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions or satisfy Exposure compliance. This Transmiller must not be co- located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED.

EU Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares thal this device (WV-002) is in compliance wilh Ihe essenlial requiremenls and olher rolovant provisions of thoc Dircctive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro- compliance

EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany GB Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (WV-002) is in compliance with the essential requirements and other relevant provisions of Radio Cquipmenl Regulations 2017. A copy of the GB Declaration of Conformity is available online at www.dji.com/curo-compliance

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. I he disposal at the communal collecting point via private persons is for trees. The owner of old appliances is responsible to bring the appliances to these collection points or to similar collection points. With this little personal effort, you contribute to recycling valuable raw materials and the treatment of toxic substances.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals