Embracing Finest EFWT 1091G WP Washing Machine Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

Warning

• Dismantle, repair or alterations ® should only carried out by profess technicians. Avoid electric shock, fire, and body injury due toimproper activity.

• Electricity supply must be unplugged with dry (4 hands. Otherwise, this may Wethands cause eleciric shack.

• Damaged or loosen wire or plug should i notbe used Otherwise electric shock, shortciruitorfire =X maytake piace.

• Do not damage wire. DO not damage or alter the wire forcibly bend, pull twist or handle the wire. Beside, please do not put weigh on or trap the wire.

• Keep child away from the washing spinning basket and do not place box or shelves next to the washing machine. children may fallnto the basket rasulting in injuries.

•  Please use the single socket with special  voltage and current matched with plug marked specification The share of the same socket with other electric appliances may cause fire dus (o excessive.

• Washing machine should not be installed in humid place o in places exposed to wind and rain. Otherwise, electricity leak causing electric shock o fire may occur.

• This washing machine is equipped with the socket. The creepage protector shall be used  if possible. o To prevent electricity leak which 13 may cause injuries.

• Do not put water in direct contact with the unit during maintenance and repair. This may cause short circuit or 77 electric shock

• Do not put gasoline, benzine, alcohol, thinner of fabrics with these stains into or near to the washing machine To prevent fire or explosion which may cause Injuries

• Do not put your hand into the basket until it has stopped completely. Evenhen e spimingof thebasketis (i), slow, there s stil a danger of being caught inthe motion, resulting injuries. Particular 7 I attention should be paid when children are Around

• Do not put your hands into the washing/ spinning basket during the washing and rinsing process. Even when the spinning s slow, hands may be rapped by clothes. Il necessarily, please press pause bution, and put your hands into the basket aftr thas stopped completely.

• Thoroughly wipe the power plug when dirtis adhering the prong or around the base of the prong Clear Failure 1o do so may cause a fire.

• This washing machine is strictly prohibited to get close to the locations with candle, mosquito- repellent incense, dog-end or other kinds of open flame To avoid injuries caused by the lock damage.

• Do not pull the wire from the socket when unplugging the unit =i To avoid electric shock o fire cause by Short circuit may result
  |

• Electricity supply must be unplugged with dry hands during maintenance and repair Electric shock or leakage may occur due lo Otherwise, electric Ceakage causing injuries deformation of plastic may occur.

• Do not wash, rinse and spin the water proof\ fabric or cloth. Sloeping bag. raincoat, cover of sking, uilles, bicycles, cars and motors Otherwise may lead to injury by abnormal vibration during Spinning or damage the washing machine, wall. floor and Clothes

• Keep hands and feet away from the buttom of the washing when itis motion. = Ports in motion beneath the unit may cause injuries.
  
  Water supply hose should be tightly screw

Failure to do so may resulting water leakage. resulting water leakage caused by loosen union nut. So please check it in time and screw tightly again

This appliance is intended to be used in household and similar applications such as: (IEC 60335-2-7)

• Staff Kitchen area in shops, offices and other working environments;

• Farm Housed;

• By clients in hotels, motels and other residential type environments:

• Bed and breakfast type environments:

• Area for communal use in blocks of flats or inlaunderettes.

• Please unplug the unit when not  using the unit for a long period of time Electric shock or leakage may ocour due to deformation of plastic parts of the unit.

• Water of above 50°C should not be used for washing  Electric shock or leakage may oceur due To deformation of plastic parts of the unit
  

• Do not stand on or put weight on the top of the UNIT Otherwise, deformation Prohibited and damage may result causing injuries

• Check water supply hose connection by turning on the water before washing Water To prevent damages caused by possible leakage due to loosen screw or not tightly.

• Please turn off the water tap when not using the unit. o prevent damages caused by water leakage.

• The appliance is not to be used by person (including children) with reduced physical ,sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

  • Children being supervised not to play with the appliance.

**PRODUCT OVERVIEW

**
Supplied Accessories

|

|

|

INSTALLATION

Installing the Bottom Cover

1. Unplug the Power Cord of the washer.
2. Gently lay down the backside of washer on a soft mat or cushion. (Be careful not to dent the Frame.)
3. Insert the attached Bottom Cover into the hooks of Leg by straightly pushing until it reaches into the back hooks.
4. Fasten the Bottom Cover with a screw.
5. Gently set the washer upright.
   

Location of Washer

1. The location of washer must remain dry and away from direct sunlight or rain.
2. Install the washer on a stable and level surface.

Inclined Floor

Unstable Floor

3. Adjust the Adjustable Leg of washer if necessary to make the washer level as shown in the figure. The maximum permissible inclination of the supporting surface is 2 °

CAUTION:

• DONOTBLOCK THE VENTILATION OPENINGS UNDER THE WASHER, WASHER WILL BE DAMAGED IF VENTILATION IS BLOCKED

Installation of water supply inlet hose

Step 1
Detach the joint hose from the water supply hose.

Step2
Sleeve the joint ring over the tap and supply hose. align with the joint hose. Make sure it is centered.

Step 3
Once align, screw in the four screws that will secure the joint hose on the tap.

Step 4
Remove the caution label, turn the  bottom part of the join hose counter anticlockwise and ensure it is tight so all seal in between the Join hose

Step 5
Take the other end of the hose and screw clockwise into the washer inlet. Make sure it is tight to prevent water  leakage.

Step 6
Once all is done, Do a quick check on pulling the join hose to ensure it is tight nd not lose.

Installation of drain hose

1. Make sure the washer and water supply are off and start locating the drain hose connector.
2. Pinch the two bands of the clamp from the drain hose connector. Connect the given drain hose in to the connector.
3. 0nce connected, put the other end of the hose into the drain spout.

Note: Please take the drain hose out of the water spout when washer is not being used for along period of time.

Changing the position of the drain hose

Depending on the use of location, the drain hose can be changed from being on the right side to being on the left side. Screw

1. Remove the cap on the Drain Mouth on the left
2. Lay the Washing Machine backward down on a soft cushion
3. Loosen the Hose Clamp and unplug the Inner Drain Pipe from (Frun( VleW) uTio the Drain Valve.
4. Push the joint on the Drain Mouth and pull the Inner Drain Pipe out of the Drain Mouth on the right side of the Washing Machine
5.  Insert the drain pipe from the mouth on the left side and snap the joint
6. .Connect the Inner Drain Pipe to the Drain Valve and fix it with the Hose Clamp
7. Install the Drain Mouth Cap on the left in the appropriate position on the right.
8. Lift the Washing Machine gently until itis placed steadily.
   

Note: The default position of the drain hose is on the right side. Before changing to the left side, unplug the Power Cord ) To Prevent hand scratches or injuries, please wear gloves.

Extension of the Drain Hose

Make sure the length of the drain hose is enough, extension of drain hose is permitted and not supplied.

CONTROL PANEL

1.DETERGENT Indication

• These are the spoon indications of the DETERGENT volume for different water level
  7-8

5-6

3-4

1-2

2.WATER LEVEL Button

• You can choose the appropriate water level that matches the load size. (Refer to table in page 9)

3.Function Button

• The Function button can be used to select “PRESETV’SOAK”,”WASHVRINSE. ‘SPIN” process. • _t •w”.

4.Digital Display

• The digital display shows the remaining time of the program. and the currently selected option.
• When press the water level, it shows the water level you set.
• When an abnormal condition occurs, it shows the warning  Code e.g Water does not flow

5.SET Button

• Press SET buttons to adjust the washing time of PRESET.SOAK. WASH, SPIN and the number of times to RINSE.

6.START/PAUSE Button

• Press this button to start the washing machine.

• To pause the program. press this button again to temporarily stop the operation.

• To restart the washer operation. press this button again.
  NOTES:

• This is not a CANCEL button.

• when pause is activated, the function indicator will be blinking. If it is not blinking. Pause IS deactivated. 0′

7.PROGRAM Button

• To choose the washing program, press PROGRAM button. NOTE:
• If you cheese the NORMAL,HEAVY Outy,OUICK WASH,JEANS,BABY programine washer will automatically begin the NEURO & FUZZY operation.
• When setting the child lock function, the child lock Indicator light up iE 9.1 child lock light up

8.POWER ON/OFF Button

• Press this button to turn on or of the power. •The washer will be turned of automatically in 5 seconds after the washing is completed.
• If you leave the washer turn on without starting operation.the power will be turned of automatically after 10 minutes.

OPERATION

Preparation of laundry before washing

• Make sure that nothing is remained in pocket. (Pin, coin or something like possibly damage clothes or washer.)
• Wool items like women lingerie articles with embroider, nylon etc, should be placed in a laundry net for extra protection.
• Always separate white or lighter coloured clothes from coloured clothes, coats from lingerie. from lingerie. I‘( isto p_revent dye from the darker co_loured clqthing seepinto lighter  coloured clothing during the washing process and light clothing can turn into off- shade colours and be ruined.

Auto program

The washing machine comes with auto sensing that will auto detect the laundry load with appropriate water level, wash, spin and rinse time accordingly.

Auto Sensing Programs

NORMAL| JEANS| QUICKWASH| BABY| HEAVY DUTY

1. Select the preferred wash program. (NORMAL, JEANS, QUICKWASH, BABY AND HEAVYDUTY)
2. .Then press “Start” button.
3. The Machine will then start operating after sensing the appropriate water level, wash and spin time.

Detergent guideline

type of detergent-follow recommendations on package.

Note: Too much detergent causes poor rinsing and too little detergent causes poor washing.

Program table

Program| Description| Cap acit y Cap (kg)| Duration| No. of Rinse| .         . Spin Time
---|---|---|---|---|---
**NORMAL***| Normal dirty clothes| 10| Depending
on load| 2| 6min
JEANS| Suitable for washing jeans| 4| 55min| 2| 6min
QUICKWASH| Not very dirty clothes| 3| 27min| 1| 3min
BABY| Suitable for children’s clothes| 7| 65min| 3| 6min
DELICATE| Suitable for gentle washing of fine fabrics| 3| 31min| 2| 2min
HEAVY DUTY| Dirty clothes like heavily soiled clothes| 7| Depending
on load| 2| 8min
BLANKET| Suitable for washing large household textiles| 4| 67min| 3| 8min
TUB CLEAN (Do not add clothes)| Wash the tub to keep the freshness| 0| 2hr| 1| 3min
RINSE & SPIN| Extra spin & rinse| 10| 34min| 2| 6min

EFWET 129 1DDG WP

Program| Description| Capacity
(kg)| Duration| No ‘ of Rinse| . Spin Time
---|---|---|---|---|---
**NORMAL***| Normal dirty clothes| 12| Depending
on load| 2| 5min
JEANS| Suitable for washing jeans| 4| 55min| 2| 5min
QUICKWASH| Not very dirty clothes| 3| 28min| 1| 3min
BABY| Suitable for children’s clothes| 7| 65min| 3| 5min
DELICATE| Suitable for gentle washing of fine fabrics| 3| 32min| 2| 2min
HEAVY DUTY| Dirty clothes like heavily soiled clothes| 7| Depending
on load| 2| 8min
BLANKET| Suitable for washing large household textiles| 4| 68min| 3| 8min
TUB CLEAN (Do not add clothes)| Wash the tub to keep the freshness| 0| 2hr| 1| 3min
RINSE & SPIN| Extra spin & rinse| 12| 34min| 2| 5min

Note: Duration is default, customers can customise according to their preferred function. The program “Normal*” with Water Level 8 is able to clean normally soiled cotton laundry. “Normal with Water Level 8 is recommended program designed to minimize water consumption for normally soiled load at rated capacity. You can use this program by adjusting manually the water level to 8.

Function

Each programs have its own amount of duration and number of times that can be fully customised by user.

Note: ** There are two methods of rinsing for the washer.
1” is rinse 1 time with water stored in drum.
1.” Is rinse 1 time with water flowing.

How to adjust the functions

Follow the flow chart on how to tune to your washing preference.

• PROGRAM
  Select program that Suite your Landry

• WATER LEVEL
  (Optional ) Select the desire water level from 1-8 if needed
  

• FUNCTION
  Choose the  preferred function to be adjusted

• SET
  Adjust the desired duration or number times.

• START
  Once setting has been customized washer can start to wash

PROGRAM: Select any program that you require for your laundry (NORMAL, JEANS, QUICKWASH, BABY, DELICATE, HEAVY DUTY, BLANKET, TUB CLEAN, RINSE & SPIN) mount of duration and number of times that can be fully customised by user.
WATER LEVEL: Adjust water level from 1-8 according to what your laundry require.
FUNCTION + SET : Choose the preferred function (PRESET, SOAK, WASH, RINSE OR SPIN) to be customised by pressing the “FUNCTION” button. The indicator besides the chosen function will blink, indicating that the function is being selected. Adjust the duration or number of times by pressing “SET” button.
Note: Adjustment can be done only while the indicator on the selected function is blinking. Repeat the above steps to adjust all other function to suit your washing preference.

Example: To adjust the “wash” duration to 15minutes under “normal” program.

1. Select “Normal” program.
2. Press the “function” button until the indicator besides “wash” function is blinking.
3. Press the set “Set” button to adjust the wash duration to 15minutes (The display panel will show “15”)
4. Press “Start/Pause” button once the program is being customised.

START: Once you have customised to your washing program and function. You can start the program by pressing “START/PAUSE”.

Preset

This is delay End function; wash cycle can be programmed to end at a later time after user set the preferred ending hours. You may choose to end the washing cycle from 1 – 24hrs.

To use preset function,

1. Press “Power” button
2. Press “Program” button and choose the required program that suits your washing.
3. Press “Function “button until the red indicator is blinking besides the “Preset”.
4. Press “Set” Button and adjust the preferred ending time (From 1-24hrs).
5. Press “Start/Pause” button to start the program.

Deactivation of End Buzzer
Upon completion of each program, there will be acoustic signal indicating the program is completed. You may deactivate the acoustic signal (End Buzzer)

• To Deactivate Buzzer after washing machine operation is completed Press and Hold Start/Pause button for 5seconds until you hear a “beep” then release the button after “beep” sound.
• Reactivate buzzer after washing machine operation is completed Press and Hold Start/Pause button for 5 seconds until you hear a “beep” then release the button.

Child Lock

Child lock function is to prevent accidental adjustment of water level during the washing operation.
Note: Child lock works only during washing operation. Child lock only disable water level adjustment during operation.

To activate child lock, Press and hold “Program” button for 4 second until the child lock indicator light is on. To deactivate child lock, Press and hold “Program” button for 4 second until the child lock indicator light is off.

GENERAL MAINTAINENCE

Clean washing machine

• Use soft clothing to wipe off the water or irt on the surface of the washer.
• Do not spray water directly to washer body
  Detergent propellant and  not allowed to use to avoid the damages on the surface.

Clean Hose Filter

(Suggest clean it every 6 months) Pull the water inlet hose out.

1. Turn off the revolver according to the figure shown.
2. Load off the “Magic™ Hose Joint filter and clean the crud with a toothbrush.
3. Install the clean “Magic” Hose to the washer body. ®Detergent, propellant and Joint fiter to revolver and watero revolver and water inlet hose

Clean the water inlet Valve

(Suggest clean it every 6 months) After long time use, The water inlet mesh bag may be blocked with crud, please \ load off the water inlet hose, take out the water inlet mesh bag from the water inlet valve, clean the mesh bag, then assemble the mesh bag in the valve and Ioad the water inlet hose.

Clean lint filter
(Suggest clean it every week)

1. take out the lint filter.
2. Pull out the scraps and wash the lint filter in the water
3. Install the Filter ( aim the frame claw to the groove below).

(Be gentle with the Lint Filer as it s fragile.)

TROUBLESHOOTING

Error
Code| Fault| Possible
causes| Action
---|---|---|---
| The washer is not working.| Power supply is not present.| ·  Press the on off button.·  Connect power supply.·   Check circuit breaker is on or fuse broken.
Washer is set to preset.| ·   Press the on/off button to reset program.
El| Water does not flow into tub or water flow is slim.| Water supply cut off.| ·  Connect to water supply·  Turn on water supply.
Metal filter in water inlet is clog.| ·   Clean the metal filter by removing any dirt that is blocking.
Water pressure is low.| ·  Adjust water supply pressure.
E2| Water does not drain out.| Height of drain hose is too high.| · Lower the drain hose
Drain hose clog.| ·   Removing any din that is blocking.
Drain hose is has been squashed.| ·   Remove and heavy object that Is touching the drain hose.
E3| Washer does not spin.| Laundry is clumped on one side of the tub.| ·   Put lesser load or reposition the laundry in the drum.
Washer is not on a level surface.| ·   Level the washer correctly or choose a location that is level for the washer.
E4| Washer lid is open.| Washer lid is open.| ·   Close the lid and press start button again.
E5| Washer does not wash.| Washer lid is open| ·   Close the lid and press start button again.
Washer is under child lock.| ·   Press and hold the Program button for 5 second to unlock.
EA| Other Faults| ·   Off the washer and call CASA after sales service centre.
EC

Note

1. During Washing or Rinsing, there is still Water inletting. This is possibly automatic water adding due to water level decrease.
2. Spin tub turns or stops timely at the beginning of spinning. This is intermittent spinning for better spin effect.
3. Water is inletting and rinsing sometimes during spinning.This is automatic lean-correction due to clothe is not equally inside.
4. There is sound like water flow after spinning. This is the sound of balance liquid in Balance Ring. It is for reducing vibration of spinning.
5. Control panel keeps warm after power off, this is caused by Remembering circuitry working.

TECHNICAL SPECIFICATION

EFWT 1091G WP Capacity: 10KG
Dimensions: 540(W)x568(D)x955 (H) mm
Net weight: 34kg
Input voltage & Frequency:230-240V/50Hz
Power Consumption: 420W
Required Water Pressure: 0.03 MPa ~ 0.8 MPa (0.3 kgflcm® ~ 8 kgffem® )
EFWT 1291DDG WP
Capacity: 12KG
Dimensions: 570(W)x593(D)x985 (H) mm
Net weight: W)x593(D)x985 (H) mm 3
Input voltage & Frequency: 220-240V/50Hz
Power Consumption: 420w
Required Water Pressure: 0.03 MPa ~ 0.8 MPa (0.3 kgflcm® ~ 8 kgflcm® )

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>