Pablo Bola Sphere LED Pendant Light Installation Guide

Pablo Bola Sphere LED Pendant Light

Product Information

• Product Name: BOLA SPHERE
• Product Type: Pendant and Chandelier
• Power Supply: 120/240V
• Light Source: LED
• Light Control: Full range light control via 0-10V or ELV dimmer
• Cord Length: 8.9ft (270cm)
• Care Instructions: Wipe with a clean, damp cloth. Avoid ammonia-based cleaners.
• Manufacturer: Pablo Designs
• Contact Information: INFO@PABLODESIGNS.COM, 888 MARIN STREET SAN FRANCISCO, CA 94124 PABLODESIGNS.COM

Product Usage Instructions – BOLA SPHERE PENDANT (120/240V)

1. Attach the mounting plate to the junction box or ceiling.
2. Wire the transformer to the building electrical system. For US wiring, connect black to black and white to white. For EU wiring, connect blue to blue and brown to brown/red.
3. Cut the cord to the desired length and pass it through the canopy. Wire the transformer to the lamp. For US wiring, connect blue to braided and red to red. For EU wiring, connect black to braided and red to red.
4. Tighten the set screws on the cord relief.
5. Bring the canopy up to the mounting plate with bolts passing through the holes.
6. Screw both caps down to secure the canopy in place.
7. For 0-10V dimmer switch installations, use the purple and grey cords.
8. Use provided gloves when handling the lamp to avoid finger marks.
9. Screw the stem onto the stationary heat sink.
10. Carefully screw the globe to the heat sink.
11. Ceiling mounting is recommended to be installed by an electrician.

Product Usage Instructions – BOLA SPHERE CHANDELIER (120V & 240V)

Important: We recommend that the fixture be installed by an electrician. The BOLA SPHERE CHANDELIER must be securely anchored to a 150lbs rated junction box or mounted to ceiling studs.

120/240V ASSEMBLY & INSTALLATION INSTRUCTIONS

INFO@PABLODESIGNS.COM 888 MARIN STREET
SAN FRANCISCO, CA 94124
PABLODESIGNS.COM

1. ATTACH MOUNTING PLATE TO JUNCTION BOX OR CEILING
2. WIRE TRANSFORMER TO BUILDING (US: BLACK TO BLACK AND WHITE TO WHITE) ( EU: BLUE TO BLUE AND BROWN TO BROWN/RED)
3. CUT CORD TO DESIRED LENGTH AND PASS THROUGH CANOPY. WIRE TRANSFORMER TO LAMP (US: BLUE TO BRAIDED AND RED TO RED) (EU: BLACK TO BRAIDED AND RED TO RED) NOTE: PURPLE AND GREY CORDS ARE USED ONLY WITH 0-10 V DIMMER SWITCH.
4. TIGHTEN SET SCREWS ON CORD RELIEF
5. BRING CANOPY UP TO MOUNTING PLATE WITH BOLTS PASSING THROUGH THE HOLES
6. SCREW BOTH CAPS DOWN, SECURING THE CANOPY

USE PROVIDED GLOVES WHEN HANDLING LAMP TO AVOID FINGER MARKS.

1. SCREW STEM ONTO STATIONARY HEAT SINK
2. CAREFULLY SCREW GLOBE TO HEAT SINK.

• LIGHT SOURCE
  LED
  FULL RANGE LIGHT CONTROL VIA 0 – 10v OR ELV DIMMER

• LIGHT SOURCE REPLACEMENT
  CONTACT MANUFACTURER FOR REPLACEMENT

• LENGTH OF CORD SUPPLIED
  8.9FT (270CM)

• CARE
  WIPE WITH A CLEAN, DAMP CLOTH. AVOID AMMONIA BASED CLEANERS.

CORD PATH DIAGRAM

1. a SECURE DRIVER TO MOUNT BRACKET WITH PROVIDED TAPE. b SECURE MOUNT BRACKET TO JUNCTION BOX OR CEILING USING APPROPRIATE ANCHOR METHODS.
   IMPORTANT! BE SURE TO REFERENCE CORD PATH DIAGRAM BEFORE MOVING ON.

2. BE SURE TO WEAVE CORD THROUGH ALL NECESSARY PARTS LISTED ABOVE BASED ON LAMP MODEL.
   a BEND WIRE ENDS BEFORE PASSING THROUGH STRAIN RELIEF. b PASS CORD THROUGH STRAIN RELIEF AND SET LAMP HEIGHT BY FASTENING BOTH (TOP AND SIDE) SET SCREWS. (IF NECESSARY: TRIM EXCESS CORD)

3. PLACE FASTENED STRAIN RELIEF ONTO MOUNTING BRACKET.
   (NOTE! STRAIN RELIEF SHOULD NEST INTO RECESS IN BRACKET SURFACE)

4. WIRE DRIVER TO BUILDING (US : BLACK TO BLACK/WHITE TO WHITE) (EU: BLACK TO BROWN/WHITE TO BLUE) NOTE: PURPLE AND GREY WIRES ARE USED ONLY IN 0-10V INSTALLATIONS.

5. WIRE DRIVER TO LAMP (RED TO RED/BLUE TO BLACK) SECURE CANOPY COVER TO BRACKET ASSEMBLY WITH CANOPY NUT. TIGHTEN UNTIL FIRMLY IN PLACE.

BOLA SPHERE PENDANT ASSEMBLY

• LIGHT SOURCE

  • LED
  • FULL RANGE LIGHT CONTROL VIA 0 – 10v OR ELV DIMMER

• LIGHT SOURCE REPLACEMENT
  CONTACT MANUFACTURER FOR REPLACEMENT

• LENGTH OF CORD SUPPLIED
  8.9FT (270CM)

• CARE

  • WIPE WITH A CLEAN, DAMP CLOTH, AVOID AMMONIA-BASED CLEANERS.
  • IMPORTANT: WE RECOMMEND CEILING MOUNTING BE INSTALLED BY AN ELECTRICIAN

USE PROVIDED GLOVES WHEN HANDLING LAMP TO AVOID FINGER MARKS.

IMPORTANT: WE RECOMMEND FIXTURE BE INSTALLED BY AN ELECTRICIAN. BOLA SPHERE CHANDELIER MUST BE SECURELY ANCHORED TO 150LBS RATED JUNCTION BOX OR MOUNTED TO CEILING STUDS.

SUGGESTED HANGING CINFIGURATION

1. DETERMINE APPROPRIATE HEIGHT ABOVE SURFACE FOR LOWEST LAMP
2. SPACE EACH LAMP SUCH THAT THEY WILL NOT TOUCH EACH OTHER
3. MOVE UPWARDS IN A SPIRAL PATTERN

NOTE: INSTALLATION REQUIRES STANDARD PHILLIPS HEAD SCREW DRIVER AND #2 FLAT HEAD SCREW DRIVER

1. ROUTE BUILDING WIRING THROUGH MOUNTING PLATE

2. ATTACH PLATE TO JUNCTION BOX WITH PROVIDED JUNCTION BOX MACHINE SCREWS

3. ANCHOR PLATE INTO CEILING STUDS ~ WITH PROVIDED WOOD SCREWS IF POSSIBLE. IF NOT, USE PROVIDED CEILING ANCHORS AND WOOD SCREWS TO SECURE PLATE TO CEILING

4. ALIGN HOLES ON MOUNTING PLATE WITH CORRESPONDING HOLES ON CANOPY COVER

5. ATTACH CABLE HOOKS TO CABLE MOUNTS ON CANOPY COVER TO SUPPORT CANOPY COVER DURING INSTALLATION. CABLE HOOKS MUST REMAIN ATTACHED TO CANOPY COVER TO ENSURE SAFE INSTALLATION

6. USING THE SUGGESTED HANGING CONFIGURATION AS A GUIDE, FEED PENDANT CORDS THROUGH ASSIGNED HOLES IN CANOPY COVER AND STRAIN RELIEFS

7. PULL PENDANTS TO DESIRED HEIGHT REFERENCING SUGGESTED HANGING CONFIGURATIONS. USE #2 FLAT HEAD SCREW DRIVER TO SET STRAIN RELIEFS

8. PRESS RUBBER PLUGS INTO UNUSED HOLES FROM INSIDE OF CANOPY COVER
   NOTE: INSTALLATION SHOWN IS FOR BOLA SPHERE CHANDELIER 3. FOR BOLA SPHERE CHANDELIER 5 AND 7, FOLLOW THE SAME WIRING PROCESS USING THE HOLE PLACEMENT OUTLINED IN SUGGESTED HANGING CONFIGURATIONS.

9. FIXTURE WIRING
   CONNECT FIXTUR WIRING TO 2 POLE CONNECTOR ON DC OUTPUT SIDE OF TRASNFORMER AS SHOWN. IMPORTANT! ONE TRANSFORMER PER LAMP

10. BUILDING WIRING
    CONNECT AC INPUT SIDE OF TRANSFORMER TO TERMINAL BLOCKS AS SHOWN AND SECURE WITH A #2 FLAT HEAD SCREWDRIVER
    NOTE: PURPLE AND GREY CORDS ARE USED ONLY WITH 010 V DIMMER SWITCH AND SHOULD NEVER BE ATTACHED TO THE TERMINAL BLOCK. CONTACT PABLO IF FURTHER INSTRUCTION IS REQUIRED

11. ENSURE ALL CABLES AND CORDS ARE TUCKED WITHIN CANOPY COVER. LIFT CANOPY COVER UP TO CEILING AND SECURE TO MOUNTING PLATE WITH PROVIDED CANOPY COVER MACHINE SCREWS

INFO@PABLODESIGNS.COM
INFO@PABLODESIGNS.EU
888 MARIN STREET SAN FRANCISCO, CA 94124
PABLODESIGNS.COM
PABLODESIGNS.EU

References

• Pablo
• Pablo

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>