CFMOTO 400-500 Plow Mount Installation Guide
- June 13, 2024
- CFMOTO
Table of Contents
CFMOTO 400-500 Plow Mount Installation
Product Information
| Product Name | CF MoTo 400-500/KodIAK 450 |
|---|---|
| Part Number | 106490 |
Kit Components
| Item # | Qty. | Description |
|---|---|---|
| 1 | 2.1 | 1 Plow Mount |
| 2 | 1 | Hardware Kit HK-112 |
| 2.1 | 4 | 5/16-18 X 1-3/8 X 2 X 1 Thread |
| 2.2 | 8 | 5/16-18 Hex Nut Flange Nylock GR5 |
Installation Instructions
- (Cforce 400/500/500 S) Position the front of the mount 4 back from the front of the center skid plate, as shown in Figure 1, and mark the grey hole locations for drilling.
- (Cforce 500 HO) Position the front of the mount 1.5 back from the front of the center skid plate, as shown in Figure 2, and mark the grey hole locations for drilling.
- (Cforce 400/500 G2) Position the front of the mount 2 back from the front of the center skid plate, as shown in Figure 3, and mark the grey hole locations for drilling.
- (Yamaha Kodiak 450) Position the back of the mount 3.5 forward from the back of the center skid plate, as shown in Figure 4, and mark the grey hole locations for drilling.
- Using a 1/2 drill bit minimum, drill out the marked holes from your plow mount. An alternate way is to cut out the outside holes to fit your U-Bolts, as shown in Figure 5 & 6.
- Hang the 4 U-Bolts (2.1) over the frame tubing and through the holes in the skid plate, as shown in Figure 7. Note: Do not pinch any lines or wires between the U-Bolts and Frame. The brake line may run next to the frame.
- Attach the Plow Mount (1) to the frame, loosely, with the U-Bolts (2.1) and nuts (2.2), as shown in Figure 8.
- Once all hardware is started, tighten hardware evenly.
Kit Components
Kit Components:
Item #| Qty.| description
1| 1| Plow Mount
2| 1| Hardware Kit HK-112
2.1| 4| 5/16”-18 X 1-3/8” X 2” X 1” Thread
2.2| 8| 5/16”-18 Hex Nut Flange Nylock GR5
Note : Make sure all hardware needed to complete this mount is in the
package. Thoroughly read through and understand the instructions before
installing.
Note: This mount fits many machines, be sure to use the right measurement
and hole locations (A or B) for your machine so the U-Bolts fit around the
frame. Center your mount and mark the grey bolt holes using the mount as a
template.
Marking The Skid Plate Bolt Locations
-
(Cforce 400/500/500 S) Position the front of the mount 4” back from the front of the center skid plate, as shown in Figure 1, and mark the grey hole locations for drilling.
-
(Cforce 500 HO) Position the front of the mount 1.5” back from the front of the center skid plate, as shown in Figure 2, and mark the grey hole locations for drilling.
-
(Cforce 400/500 G2) Position the front of the mount 2” back from the front of the center skid plate, as shown in Figure 3, and mark the grey hole locations for drilling.
-
(Yamaha Kodiak 450) Position the back of the mount 3.5” forward from the back of the center skid plate, as shown in Figure 4, and mark the grey hole locations for drilling.
-
Using a 1/2” drill bit minimum, drill out the marked holes from your plow mount. An alternate way is to cut out the outside holes to fit your U-Bolts, as shown in Figure 5 & 6.
-
Hang the 4 U-Bolts (2.1) over the frame tubing and through the holes in the skid plate, as shown in Figures 7.
Note : Do not pinch any lines or wires between the U-Bolts and Frame. The brake line may run next to the frame. -
Attach the Plow Mount (1) to the frame, loosely, with the U- Bolts (2.1) and nuts (2.2), as shown in Figure 8.
-
once all hardware is started, tighten hardware evenly.
©2023 Copyright
Kappers Fabricating, Inc. All rights reserved
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>