HYPERX Clutch Gladiate Wired Xbox Controller User Guide
- June 13, 2024
- HYPERX
Table of Contents
HYPERX Clutch Gladiate Wired Xbox Controller
Overview
- A Analog sticks (L3/R3)
- B Xbox button
- C Power LED
- D ABXY buttons
- E View button
- F D-Pad
- G Share button
- H Menu button
- I Trigger locks
- J P1 button
- K P2/P3 buttons
- L 3.5mm headset jack
- M Bumpers (LB/RB)
- N Triggers (LT/RT)
- O USB-C port
- P USB-C to USB-A Cable
Setup
Connect the controller with the provided USB cable to your Xbox or PC.
Programmable Buttons
Assign/Re-Assign P2 & P3
- Hold P1 and Release when LED is slowly flashing
- When LED is flashing slowly, press one of the following buttons to assign.
- When LED is flashing rapidly, press either P2 or P3 to assign your selected button.
Clear individually P2 or P3
When LED is flashing slowly, press either P2 or P3 to clear its button mapping
.
Trigger Locks
- Move slider to position 1 to unlock full trigger motion.
- Move slider to position 2 to lock and reduce trigger motion.
Questions or Setup Issues?
Contact the HyperX support team or see the user manual at
hyperx.gg/support
WARNING: Permanent hearing damage can occur if a headset is used at high volumes for extended periods of time.
Simplified Declaration of Conformity
Hereby, HP declares that the radio equipment is in compliance with Directive
2014/53/EU. The full text of the EU Declaration of Conformity is available at
the following internet address:
www.hp.eu/certificates (search with Model
Name)
UK only: Hereby, HP declares that the radio equipment is in compliance with the relevant statutory requirements. The full text of the declaration of conformity is available at the following internet address: www.hp.eu/certificates (search with Model Name)
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o± and on, the user is encouraged to try correct the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Any special accessories needed for compliance must be specified in the instruction manual.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment.
CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
India RoHS Statement
This product, as well as its related consumables and spares, complies with the
reduction in hazardous substances provisions of the “India E-waste (Management
and Handling) Rule 2016.” It does not contain lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers in
concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except
for where allowed pursuant to the exemptions set in Schedule 2 of the Rule.
- Copyright 2022 HyperX and the HyperX logo are registered trademarks or trademarks of HP Inc. in the U.S. and/or other countries. All registered trademarks and trademarks are
property of their respective owners.
References
- Support – HyperX ROW
- Laptop Computers, Desktops, Printers, Ink & Toner | HP® Australia
- Regulations Certificates | HP® United Kingdom
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>