h and j 1079 Inflatable Spa Instruction Manual

h and j 1079 Inflatable Spa

Product Information

Product Name: Spa Gonflable

Ref1079_121082
Year: 2021-2022

General Safety Rules

Explanation of Symbols

• This product must not be disposed of with household waste!
• Be especially careful when using this article!
• Warning against the risk of electric shock!
• Warning! Read the safety instructions carefully. Noncompliance with safety measures may result in injury or severe damage. Keep the instructions for use in a safe place.
• Note: Unplug the power plug!
• Warning! Make sure the product is grounded.

General Safety Instructions

• Follow the general safety instructions provided in the manual to ensure safe usage of the product.

Parts List

• The parts list includes various components required for the installation and operation of the spa.

Technical Specifications

• The technical specifications provide detailed information about the various parameters and features of the spa. This includes motor power, power supply, temperature increase rate, number of seats, maximum water capacity, number of massage jets, top cover material, pool materials, foam thickness, and more.

Installation

• The installation process involves setting up the spa in either an outdoor or indoor location.

Before Installation Outdoors

• Prior to installing the spa outdoors, ensure that the area meets the necessary requirements for safe installation.

Before Installation Indoor

1. The floor must be able to support the weight of the spa occupants.
2. The floor must be a flat, non-slip surface.
3. Before placing your spa indoors, make sure that an adequate drainage system is installed, available, and can be reached. Think carefully about the location of your spa before installing it.

Installation

1. Place the groundsheet on a flat, even surface free of sharp objects.
2. Unpack the spa on the groundsheet.
3. Remove the protective plastic from the clips and connectors.
4. Assemble the hand pump, pressure gauge, and hose. Insert and twist until they are locked.

Note: Refer to the manual for detailed installation instructions and diagrams.

• Limited Warranty – Terms and Conditions.
  This warranty only applies to the original buyer. The warranty period begins on the day of purchase and lasts from 1 to 6 months depending on the elements. The warranty is not transferable to posterior buyers. This warranty is subject to the limitations and exclusions detailed below.

Warranty period

• 1-month warranty for the spa.
• 6 months warranty for electrical elements. »
• Thank you for purchasing our product. Please read the user manual carefully before using the product for the first time. If you have to transfer this product to a third party, please attach the user manual together.
  Drawings in this manual may not correspond to physical objects. Please refer to physical objects.

General safety rules

Explanation of symbols

• This product must not be disposed of with household waste !
• Be especially careful when using this article !
• He was warning against the risk of electric shock!
• Warning! Read the safety instructions carefully. The no-compliance with safety measures may result in injury or severe damage. Keep the instructions for use in a safe place.
• Note: Unplug the power plug!
• Warning! Make sure the product is grounded.

General safety instructions

• The device must be supplied by a residual current device (type RCD / GFCI) whose rated tripping current does not exceed 30mA.
• Electrical installations must meet the requirements of local standards. Electronics earthed must be permanently connected to fixed wiring.
• Any damage caused to an electric cable must be replaced by a competent party immediately before any further use.
• It is recommended not to use an extension cord to connect to the power supply electric.
• RISK OF ELECTRIC SHOCK . Never operate an electrical appliance external / additional when you are in the spa or when your body is wet.
• Keep electrical appliances away from the spa.
• RISK OF ACCIDENTAL DROWNING . Children are prohibited from using the spa unless they are supervised at all times by a responsible adult.
• For health and safety reasons, we do not recommend that children under the age of 8 years of using our spas.
• For children 8 years and older, we recommend not to exceed 37 ° C.
• When not in use, the cover should be installed and locked to help retain the heat. This also helps prevent unsupervised children from accessing the spa.
• Take a shower before using your spa. Cosmetics, lotions, etc. on the skin can degrade water quality.
• Do not turn on your spa if there is a possibility that the water in the spa or control system be frozen.
• Pets should be kept away from your spa at all times.
• Soaking in hot water during pregnancy can cause damage to the skin. If you have any special concerns, please consult your doctor before continuing to use your spa.
• Consumption of alcohol, drugs or medication before or during the use of your spa may increase the risk of drowning.
• People with a history of heart disease, hypo tension / hypertension, high blood pressure,circulatory system problems or diabetes should see a doctor before to use the spa. People taking medication should consult their doctor before using the spa. Some medicines can make you drowsy,while others can affect heart rate, blood pressure and circulation during use.
• Spa water should never exceed 42 ° C (107 ° F). Operating temperatures between 38 and 40 °C are considered safe for a healthy adult. Lower temperatures are recommended for young children, and when use exceeds 10 continuous minutes.
• A maximum temperature of 42 ° C can be programmed for the water.Once the cover is removed, the water temperature will automatically drop because heat is released by evaporation. The additional 2 ° C compensates for the heat loss that can occur. Once you are ready to use, reduce the maximum temperature to the value recommended temperature of 38- 40 ° C (100-104 ° F) and make sure that the measured temperature does not exceed 40 °C.
• Immediately exit your spa if you feel uncomfortable or drowsy.
• Do not turn on the spa when it is empty. It could cause damage irreparable to the pump system, which will void any warranty period• To prevent damage to your pump and heating system in cold weather,your spa is equipped with 365 Freeze Guard technology. Set the temperature to 5°C, this will prevent the water in the system from freezing.
• Always add chemicals to the water jug ​​to avoid strong vapors or violent reactions that can result in chemical spraying dangerous.
• To prevent accidental resetting of the thermal circuit breaker, this device must not be powered by an external switching device, such as a timer, or connected to a circuit which is regularly started and stopped by the utility.
• WARNING: An adequate drainage system must be provided to treat the water overflows.
• IMPORTANT: For installation, the surface must be smooth, flat, level and capable of support the weight of the spa, water and users equally. For example, the weight of the spa filled with a square of 6 people: 980 kg (approximately) plus the combined weight of the occupants.
• It is the responsibility of the spa owner to ensure the integrity of the site at all times.

Parts list

Please check that all parts are present in your package before the first time of use (see 3. Technical specifications)

Technical specifications

gauge, 1x filtering, Coverage1x filter, Inflation hose, 2x safety clip wrenches, repair patch, valve

wrench

Content Package 2| Control box, Connection hose 3x , Toric Seal 6x
Outdoor pool size| Ø1.80m x0.65m
---|---
Indoor pool size| Ø1.75m x0.65m
Net weight Package 1| 22 kg
Net weight Package2| 9 kg

Setting up

Before installation outdoors

1. Place your spa on a solid and level base, avoiding sharp objects as they could damage the spa.
2. Make sure your spa is plugged into an external power outlet, installed by a professional and weather proof. We do NOT recommend the use of a extension cord as this may present a fire hazard.
3. Do not place your spa in direct sunlight, or over-inflate it, as this will cause the spa to swell in some areas as the PVC heats up in the sun. This bulge could also put additional stress on the welds internal, resulting in weld failure.
4. When filling, draining or using, water may spill out. Install them At proximity to a drainage point capable of handling the volume of water

Before installation indoor

1. The floor must be able to support the weight of the spa occupants.
2. The floor must be a flat, non-slip surface.
3. Before placing your spa indoors, make sure that an adequate drainage system is installed,available and can be reached. Think carefully about the location of your spa before to install it.

Installation

1. Place the groundsheet on a flat, even surface free of sharp objects.
2. Unpack the spa on the ground sheet.
3. Remove the protective plastic from the clips and connectors.
4. Inflating valve, air jet connector, water inlet, water outlet, drainage outlet.
5. Assemble the hand pump, pressure gauge and hose. Insert and twist until they are locked.
6. Locate the inflation valve. Remove the valve cap. Connect the hose by turning clockwise to lock it. The central button MUST be at the top .
7. Use a double-acting hand pump to inflate. (Air pressure 7 PSI). About 7 PSI.
8. Inflation takes 2 minutes (approximately). Note: The drainage outlet must be placed at outside the spa.
9. Once inflated, turn counterclockwise to release the hose and replace the valve cap.
10. Unpack the outdoor unit, screw the pipes 3x onto the outdoor unit in the order shown.
11. Align the pipes with the respective connectors and screw them into place. Plug in, turn on.
12. Interior Features: Water circulation outlet, filter connector and plug drainage
13. Screw the filter cartridge onto the filter connector.
14. Add the filter protection cover to the filter cartridge.
15. Add water to the level. No higher than the “MAX” level.
16. Set the temperature on the control panel.
17. Clip on the top cover to retain heat.
18. Double locking clips with security keys.

Tighten the inflation valve

• Over time, the inflation valve may loosen. Use the valve wrench provided for tighten, maintaining air tightness.
• Important : When using the wrench – do not loosen the valve, as it may break.

Use

Temperature adjustment

• Press SET TEMP / LOCK and the digits on the display screen will start to flash.
• Increase / decrease the temperature by pressing TEMP UP or TEMP DOWN .
• Choose the desired temperature, then press SET TEMP / LOCK again to confirm. Temperatures can be set between 5 ° C and 40 ° C. (see instructions for safety for recommended operating temperatures).

Inflation / air jets

• Press INFLATE / AIR JETS to start the air jets – a red light will appear. Press this button again to stop the operation of the air jets – the indicator light red goes out.
• The air jets stop automatically after 20 minutes. To reset them, wait 10minutes and press INFLATE / AIR JETS . The air jets can be stopped / started at any moment during their 20-minute cycle.
• The air jets stop after 20 minutes to prevent overheating of the internal pump

Heating

• Press HEATER , a red light will appear. Press HEATER again and the heating system will stop, the red light will go out.
• When the heating system is on, the filtration system is activated automatically to circulate the water. When the temperature has reached 1 ° C above the preset temperature, the heating system stops working, but the indicator light remains alight. The filter pump will continue to run even if the heater is not running.
• When the water drops 1 ° C below the pre-set temperature, the heating system automatically heats the water up to 1 ° C above the selected temperature. Once this temperature is reached, the heating will stop to allow the temperature to settle, and stabilize at the preset value.

Filtering system

• Press FILTER , a red light will appear, the pump will start to run. Press FILTER again to stop the pump, the red light goes out.
• After about 168 hours, HR will appear on the display screen (blinking) with a signal warning. The red light will light up on FILTER , the pump will not be operational. the heating system will not work either and the red light will go out.
• To make sure the filtration system is off, press FILTER . HR on screen display will disappear along with the warning tone. The water temperature will be displayed, all functions will return to normal. The key CF and tone warning messages remind the user to replace the filter

Maintenance and repair

Water level

• Water should be filled and held between the ‘Min’ and ‘Max’ fill lines asmarked on the inside wall of your spa.

Importance of water treatment

• You should regularly monitor and properly treat your spa water.
• People with the following characteristics are at higher risk, including :
• Diabetes, lung and heart disease
• Smokers and heavy drinkers
• Anyone with a weakened immune system
• People with chronic respiratory or kidney diseases
• For more information, consult your doctor.

Water and Legionnaire’s Disease?

• Legionnaires’ disease can be contracted by inhaling small droplets of water (called aerosols), which are suspended in the air and contain the bacteria. Certain conditions increase the risk of leg ionellosis if:
• The water temperature in all or some parts of the system is between 20and 45 ° C, which is conducive to the growth of the bacteria.
• It is possible that breathable water droplets are created and the water is stored and / or recirculated.
• There are deposits that can promote bacterial growth by providing a source nutrients for the body, for example rust, sludge, scale, material organic and biofilms (from the body).

Cleaning

• Detergent residues, dissolved solids from swimsuits and chemicals gradually accumulate in the water. To clean your spa, use soap and water, then rinse thoroughly.
• Please note : Do not use hard brushes or abrasive cleaners.

Repair of punctures

• If your spa is torn or punctured, use repair patches. Dry the area completely, apply strong adhesive to repair the patch, then cover the damaged area. Smooth the surface to remove any air bubbles. Let dry for 12 hours before to use the spa.

Storage

How to empty your spa

1. Disconnect the spa from the electrical network.
2. Unscrew the plug from the drain port, located near the spa pumping system. Make sure that the drain plug is inserted to prevent unexpected draining.
3. Remove the drain plug from the outlet on the floor level of the spa, so that the water can drain to flow.
4.  After the spa is emptied, use a sponge to soak up the excess water. Turn on the spa,which will allow you to use the air blast function for 20 minutes (one complete cycle) to drain the water and dry the pipes. If it is not completely dry after the first cycle,repeat the operation.
5. When draining is complete, replace the drain plug and outlet cap.
6. Unplug the pump and the heating system and dry them completely

How to deflate your spa

1. Remove the filter cartridge and the filter bag.
2. Locate the inflation valve.
3. Remove the valve cap by turning 90 ° C counterclockwise.
4. Press the inflation valve by turning it 90 ° clockwise to lock it in place, which releases air.
5. Fold carefully, removing as much air as possible through the open valve.
6. When completely deflated, turn the inflation valve 90 ° counterclockwise to close it.
7. Replace the valve cap and turn 90 ° clockwise to release the valve to close.

Stockage

• Make sure all water is completely drained from the spa and pumping system. It is essential for extending the life of your spa. We recommend the use of a wet / dry vacuum to help blow / suck water from hoses and pumping lines. Remove the filter cartridge.
• The spa should be placed in the bag provided and stored in a dry, elevated place off the ground and away from extreme temperatures.
• Note: When not in use, store it in a dry place with moderate temperature,as subzero temperatures can seriously damage your spa.

When to change your spa filter

• Keep your spa clean and free from contaminants. For optimal operation, unscrew the filter and rinse it with clean water after each use to remove small particles and residues. The filter is one of the most important elements in ensuring the proper functioning of the your spa.

1. Remove the protective cover from the filter bag and then remove the filter.
2. Rinse the filter under a cold tap and reuse it. You can also wash your filter machine (place it in a pillowcase) to keep it clean and to maintain its performance.

Replace your old filter with a new one if :

• The filter remains dirty after cleaning.
• Holes are visible in the paper.
• The paper is visibly worn.
• Put the filter protection cover back on the filter and attach it to the filter connector by turning it clockwise. Do not over tighten, as this may cause a “clicking” noise.
• Do not forget ! Check your filter every day!
• To help keep your water clean, check your filter cartridge daily.

Troubleshooting

the air pump has cooled, insert the plug and press the air jets button to activate it. Wait 10 minutes and restart. Call customer service if the pump does not restart.
The system heating does not work.| The temperature is set too low.

Dirty filter cartridge. Improper water levels. Heating element failed

| Set to a higher temperature (20 – 40 ° C)than the current water temperature. Clean / replace the filter cartridge. Add water to specified levels. Call customer service if you don’t resolve the problem.
The system filtering does not work/ noise of rattling when setting filter step| Dirty filter cartridge. Something is wrong with the case power supply| Clean / replace the filter cartridge. Call customer service if it is not reset.Ask a professional electrician to check the correct functioning of the power supply electric from the house.
Spa leak| The spa is torn or

perforated.

| Use the repair patch provided.
Water is not clean.| Filtering time insufficient. Dirty filter cartridge. Poor water maintenance.| Increase filtration time. Clean / replace the filter cartridge. Refer to the manufacturer’s instructions for chemical products.
Temperature of the screen is more than42 ° C, after stop the function of heating.| Residual water from the spa will continue to be heated by residual temperature . The water inlet by the filtration system can be blocked.| Unplug the power plug and wait. The temperature will start to drop and come back to normal.

Clean the entrance.

Call customer service if it is not resolved.

Control panel error codes

displayed on the screen with a signal warning. The red light will be always on on the filter, the pump will not be operational. The system heater will not work, and the red light will be off on the heating.| Check the filter and change it if necessary. Once it’s done,press the filter again. The code HR error will disappear and the audible signal will stop. The water temperature will be displayed, all functions.
SL/HL| Question of temperature| Contact customer service
SH| Water temperature sensor| Contact customer service

Recycling instructions

Recycling and packaging

• Be sure to follow the guidelines and recommendations in force in your region for packaging recycling. Sometimes the packaging may contain plastic bags -carefully keep them away from children. There is a risk of suffocation!

Disposal of old devices

• Recycle your old devices according to local guidelines and recommendations concerning the treatment of waste.
• At the end of the life of the item do you dispose of the materials properly so that asuitable recycling is permitted. If you are not sure how to do the right thing,local garbage caterers are happy to help.

Meaning of the “trash can” symbol

• Protect our environment, electrical devices should not be thrown in the classic trash. Go to the recycling centers provided at this effect to get rid of electrical appliances that you do not serve more. Thus, you help to avoid potential negative effects on environment and human health due to poor waste treatment. You thus make your contribution to the recovery of waste,recycling and any other form of upgrading of old devices electrical and electronic. You can get information about places to take your devices to local authorities or your municipality.

After-sale service

For the sake of efficiency, and exact collection of information, thank you to send us an email beforehand with your postal and telephone details, as well as the nature of the breakdown, to process your request before your call. Thanks in advance :

In case of emergency

company| habitatejardin
Site| http://www.habitatetjardin.com/
After-sales service| http://sav.habitatetjardin.com/
Telephone|
Fax|
Mail| sav4@habitatetjardin.com
Opening days and hours| undi – jeudi : 9h-12h et 13h -17 h    Vendredi : 9h-12 h

Documents / Resources

| h and j 1079 Inflatable Spa [pdf] Instruction Manual
1079 Inflatable Spa, 1079, Inflatable Spa, Spa
---|---

References

• Habitat et Jardin : Envoi d'une demande d'assistance
• Mobilier de jardin et univers de la piscine - Habitat et jardin.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>