Nakamichi NDSD200 DSD Player with DSP User Manual

NDSD200
User Manual

NDSD200 DSD Player with DSP

DSD PLAYER WITH DSP

INTRODUCTION AND TROUBLESHOOTING

Thank you for your purchase and welcome to the world of Nakamichi! Please keep your original proof of purchase or invoice in a safe place in case of any warranty claims. Do
also, mail or register your warranty With the official Nakamichi service centers and/or agents to ensure that you are provided with the relevant technical support if required.

NOTICE

1. To prevent short circuit, please keep the device away from water or damp places.
2. If water or any other liquid enters the device, cut off the power immediately, and inform the nearest Nakamichi Service Center or Agent to inspect the product.
3. Users are not recommended to disassemble the device as there are no user-serviceable parts inside, please contact the nearest Nakamichi Service Center if necessary.

TROUBLESHOOTING

Ensure all cables and parts are securely connected before turning on the power. Shown below is the basic troubleshooting procedure that you should follow.

Troubleshooting method:

• Check the ACC connection and make sure it’s secure.
2| No Sound| • Double-check if the unit is in MUTE mode.
• Check if you have chosen the correct input channel.
3| Unable to connect through USB| • Check the USB connection and make sure it’s secure.
• Check if the driver ” HID-compliant device ” has been properly installed in your PC.

WHAT’S IN THE BOX

PRODUCT TECHNICAL DATA

Product Data

Dynamic Range(RCA Input)| ≥100dB
S/N(RCA Input| >55dB
THD| <0.5%
Frequency Response| 20Hz-40KHz
Input Impedance| High Level: 510
Low Level Output Impedance| 510
Signal Input Range| RCA: 7.5Vpp; High Level: 26Vpp
Signal Output Range| RCA: 7.5Vpp; Max Power: 8CHx5OW
Working Temperature| -20 – 70°C
Supported Audio Formats| DSD64/DSD128/DSD256/Mp3/WMA/WAV/APE/FLAC DSD file format: “.dff” , “.dsf”
Support hard disk capacity| 2T
Power| DC 9V-15V
REM Input| High Level Input Signal: Hl +/H1- or ACC control cable
REM Output| +12V Startup Voltage Output(250mA)
Standby Power| 0.1W
Net Weight| Approx.1.2kg
Product Dimension| 190(L)xl 53(W)x55(H)mm
Technical Sheet

Input Type| 6 CH High Level, 4 CH Low Level, Built-in Bluetooth, U disk music
Output Type| 10 Channels Low Level, Optical, Max Power: 8CHx5OW
Output Gain| Gain Range: Mute,-59.9dB-6dB
Output Signal EQ| 31 Band Equalizer Engine:
1. Frequency range: 20Hz-20KHz, 1 Hz Accuracy 2.Q value (slope): 0.404-28.852
3.Gain: -20.0dB- +20.0dB, 0.1dB Accuracy
Output Signal Crossover| Each output is equipped with multi-order high and low pass independent filters.
1.Filtering types: Link-Ril, Butter-W, Bessel
2. Filtering frequency division point: 20HZ-20KHz. Resolution 1 Hz
3.Filter slope (slope) setting: 6dB/ Oct to 48dB /Oct and OFF
Output Phase and Time Alignment| Each output channel can be adjusted for phase and delay, parameter range:
Phase: in-phase or reverse-phase (0. /180.)
Delay: 0.000 to 20.000ms. 0 to 692 cm, 0 to 273 inch
Presets| 6 Presets into the device

PRODUCT DIMENSIONS

INSTALLATION INSTRUCTIONS

THE SPEAKER WIRING IN NORMAL MODE

INTRODUCTION

1. USB2.0 Port, Connect to the computer tuning software
   No need to download the driver installation, connected to the computer sound software is installed automatically.

2. USB port
   Insert the USB flash drive and play the song in the USB flash drive under the player audio source.
   SUPPORTED AUDIO PLAYBACK LIST
   **** Audio| Stream| Sampling Rate| Remark
   ---|---|---|---
   MP3| 32kbps-384kbps| 8/11.025/12/16/22.05 24/32/44.1/48KHz| MP EG1/2/2.5 layer 118(111
   WMA| Okbps-320kbps| 8/11.025/12/16/22.05 24/32/44.1/48KHz| WMA standard
   4/4/1/7/8/9.1
   WAV| 32kbps-384kbps| 8/11.025/12/16/22. 5/ 24/32/44.1/48KHz| 4bit ADPCM only
   | | 8/16/22.05/24/32/| PCM Bit width
   APE| all bitrates allowed| 44.1/48KHz| 8/12/16/24bits
   | | 8/16/22.05/24/32/| PCM Bit width
   FLAC| all bitrates allowed| 44.1/48KHz| 8/12/16bits
   DSD64| all bitrates allowed| 2.8224MHz| dsf dff
   DSD128| all bitrates allowed| 2.8224MHz| dsf dff
   DSD256| all bitrates allowed| 2.8224MHz| dsf dff

SUPPORTED DEVICES

3. The controller port
   Data call and total volume adjustments can be performed by the line controller.
   

4. Optical input port
   Connect on-board or other audio equipment and switch the sound source of the machine to digital output.

5. High level output port

6. High level input and power port
   **** 1~6 High level input.

7. Machine start mode switch
   ** When the switch is turned to the “ACC” terminal, the machine is started by ACC, and when it is turned to the “HOST” terminal, the machine is started by the high level H1+/H1- input signal. **

   ---

8. Power indicator light/Protection indicator light
   Low level output port
   **Connect up to 10 channels of low-level output. **

   ---

9. Low level input port
   **** Connect up to 4 channels low level intput.

SOFTWARE INTRODUCTION

PC Software Operation Introduction
(PC can be downloaded from the official website (http://www.nakamichicaraudio.com, CONTACT, downloads)) Computer Configuration Requirements: Screen resolution higher than1280 x 768, otherwise the software Ul is incomplete and only suitable for windows operation system laptops, desktops,s, and pads.

1. Menu editing area
   
   Main functions: File, options operation.
   a. Click the “File” pop-up window, and select to load the scene on your computer, save it as scene on your computer, load the whole machine scene or save the whole machine scene.
   Note: If you need to share tuning parameters, please connect the machine, and “save machine scene” to the personal computer to share this ” machine scene”.
   b. Click on “Option” to select Chinese and English switching, Noise Gate, RESET, InPutVOL, and About(A)
   

2. Function editing area
   Main functions: scene, master source, mixer source, channel type, link, mixer, and mode settings.
   a. Scene: 6 sets of scene data can be recalled or stored.
   b. Master source: Click the input audio source drop-down list to select the input audio source. BT, Hi-Level, Low Level, and DSD.

c. Reset: Click Reset to clear the channel type or restore the default channel type.
d. Link: Click the Link to set the Link synchronization mode: copy from left to right or copy from right to left.
e. Click “Mixer” to enter the mixing interface, the interface is as shown below.
f. Click “Audio” to switch to Sound mode.

3. Main volume and software connection editing area
   Main functions: master volume and computer software connection settings.
   a. Main volume adjustment range: off, -59.9~6dB. Click the speaker button to mute the main volume.
   b. Click the “Not Connected” button to connect the host with a PC.

4. Output channel type editing area
   
   Main function: configure the type of output channel.

5. Channel delay, volume, phase editing area
   a. Push the fader left or right to adjust the sound size, or enter a value or roll the mouse wheel in the volume input box to adjust the sound size. Click the speaker button to switch mute.
   b. Positive phase adjustment: Click［ 0°］or［ 180°］ to switch between the positive phase and reverse phase.
   c. \Delay: set the delay value by scrolling the mouse wheel in the delay input box, or enter the value to set the delay value.
   d. Delay Unit button: Click the drop-down list to select milliseconds, centimeters, and inches.
   6. Channel divider editing area
   Main Function Setup: Channel High & Low Pass Filter Setup.
   Adjustable: Filter Type, Frequency point, and Q Value (Gradient or Slope).

6. Equalizer editing area
   
   a. Reset EQ: It is used to restore the parameters of all equalizers to the original pass-through mode (the frequency of the equalizer, the Q value, and the gain are restored to the initial value).
   b. Restore EQ: Switch between the currently designed equalizer state parameters and the pass-through mode (the gain of all equalization points is restored to 0 dB, and the frequency and value are unchanged).
   c. Click PEQ Mode to switch to GEQ Mode. The Q value and frequency cannot be adjusted in the
   PEQ Mode interface.

7. Channel EQ editing area
   

Main function configuration: Equilibrium design of current output channel, 31-band equalization adjustable: frequency, Q value (response bandwidth), and gain (increasing or decreasing the frequency response amplitude near the frequency point).

SOFTWARE INTRODUCTION(SMARTPHONE)

Smart-phone Software Operation Instruction
(APP can be downloaded from the official website(http://www.nakamichicaraudio.com,CONTACT, Downloads))

1. Home interface
   It can restore factory settings, share sound effects, save sound effects, turn on local sound effects, check the model and version number of the unit, and exit the software
   operation; volume, master source, storage, and recall of 6 sets of preset scenes.
   A. Connection Status:
   Red means not connected, and green means connected.
   B. Menu:
   You can restore factory settings, share sound effects, save sound effects, turn on local sound effects view the model and the version number of the machine, and exit
   the software operation.
   C. Master source:
   Master source: Bluetooth / Hi.level /Low level / DSD.
   D. Volume adjustment:
   Press and hold the volume scale clockwise or counterclockwise to adjust the volume. The main volume range is 0~66, The subwoofer range is 0~60.
   E. Scene preset:
   There are 1~6 presets to choose from.
   F. Advanced settings:
   Click [Advanced Settings] to enter the settings of the delay interface, channel interface, EQ interface, and mixing.

2. Delay interface
   Sound field positioning output delay adjustment.
   G. Unit switching:
   Switch between milliseconds, centimeters, and inches.
   H. Delay setting:
   Click the setting window of the corresponding channel. Slide the dots left and right to set the delay value. Delay settings can be made for CH1~ CH10 speakers.
   Delay range: millisecond range: 0.000~ 20.000; cm range: 0~692; inch range: 0~273.

3. Channel interface
   Channel high-low-pass crossover setting with high-low-pass independent filtering.

Adjustable: Filter type, frequency, and Q value (slope or slope).
I. Output channel selection:
Ten channels are available.
J. Output channel volume setting:
You can adjust the volume by sliding left and right. The volume range is 0~60. Click the speaker button to mute. Configurable output channel type, forward and reverse
switching.
K. Channel divider selection:
Channel type: Choose from Link-Rill,
Butter-W and Bessel.
Frequency Range: 20HZ~20KHz.
Slope selection:
6dB/Oct, 12dB/Oct, 18dB/Oct, 24dB/Oct, 30dB/Oct, 36dB/Oct, 42dB/Oct,48dB/Oct and OFF can be selected.
L. Joint tuning settings:
Click[link] on the joint debugging window that will pop up, and select the joint debugging method.
4. EQ interface
Corresponding to the adjustment of the output channel EQ curve (gain, Q value, and frequency); reset equalization, pass-through equalization, or parametric equalization operation settings.
M. EQ display:
Edit the display area.
N. Output EQ gain, Q value, and frequency settings:
Output EQ gain setting: A total of 31 EQ. left and right sliding screens can select EQ, you can drag the slider up and down. Select the first line value, and drag the slider bar left and right in the pop-up dialog box to adjust the adjustment range: -20dB ~ +20dB.
Q value: Click the second line value, and drag the slider bar left and right in the pop-up dialog box to adjust, the adjustment range is 0.404 ~ 28.852. Frequency setting: Click the third line value, and drag the slider bar left and right in the pop-up dialog box to adjust it. The adjustment range is 20Hz ~ 20KHz.
O. Reset equalization, restore equalization, pass-through equalization settings: Click [Reset EQ] to restore the parameters of the 31-band equalizer to the original pass-through mode (the equalizer frequency, Q value, and gain are restored to their initial values). When there is channel adjustment, display [straight-through equalization], click [straight-through equalization], click [OK], all values (frequency, Q value and gain) will return to the initial value. At this time, the [straight-through equalization] the button will become [recovery equalization]. Press the button and click [Resume Equilibrium], all values (frequency, Q value and gain) will be restored to the value before the pass-through. Click [P.EQ Mode], click [OK] to switch to Graphic Equalization, click [G.EQ Mode], click [OK] to switch to Parametric Equalization.
5. Mixing interface
Four sound source modes can be selected. It includes the mixing selection and adjustment of 6 groups of high-level, Bluetooth left and right channels, DSD left and right channels, and aux left and right channels. The adjustment range is 0-100.

CONNECT WITH US ONLINE TO EXPLORE NAKAMICHI’S COMPLETE RANGE,
INSTRUCTIONS & SOFTWARE DOWNLOADS, AND WARRANTY REGISTRATION.

http://www.nakamichicaraudio.com
WWW.NAKAMICHICARAUDIO.COM
nakamlchi.global
nakamichi.caraudio
Nakamichi Corp, Japan
Made in China

References

• Nakamichi Mobile Audio Systems – Nakamichi Car Audio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>