Triminator Hybrid Trimming Machine User Guide
- June 12, 2024
- Triminator
Table of Contents
Triminator Hybrid Trimming Machine
The HybridTM – Product Information
The HybridTM is a continuous throughput trimmer designed to process product as it’s fed. It has the capacity to process up to 40 lbs per hour (wet) and 15 lbs per hour (dry) with a single trimming unit. For optimal results, it is recommended to operate the trimmer in a cool, low-humidity environment.
Start-up Sequence
Before starting the machine, perform a safety check. Once confirmed, follow the start-up sequence:
- Adjust the tilt of the machine as required.
- Set the vacuum pressure to the desired level using the MIN (1) and MAX (6) controls.
- Use the emergency stop button if needed.
Suggested Start Settings
The Triminator HybridTM is capable of trimming at various moisture levels. It is important to know your moisture content to determine the appropriate starting settings. Here are the suggested settings based on moisture content:
Moisture Content| Machine Tilt| Vacuum Lever Position| Tumbler Speed| Blade
Speed
---|---|---|---|---
WET (18% +)| 2.5 Turns| MAX (6)| 3| 6
SEMI-DRY (11-18%)| 4 Turns| MAX (6)| 3| 6
DRY (9-11%)| 7 Turns| 4 to MAX (6)| 4| 3
Product Usage Instructions
- Load bucked and destemmed product into the hopper or infeed conveyor (if applicable). It is recommended to keep the tumbler around 3/4 to full of material. Too little material may result in over-trimmed product, while too much material may lead to poor trim quality due to low vacuum suction.
- Check the quality of the trim from your first batch and adjust settings if necessary.
- Machine Tilt: Higher tilt moves the product through the tumbler faster, while lower tilt allows more time in the tumbler.
- Vacuum Suction: Higher pressure pulls leaves closer to the blade, while lower pressure reduces over-trimming.
- Tumbler Speed: Slower speeds allow more cuts per rotation but can result in product clumping. Higher speeds may prevent proper tumbling. Aim for a tumbling wave of product.
- Blade Speed: Faster speeds increase the number of cuts per tumbler rotation.
- Refer to the user guide for troubleshooting tips regarding trim quality.
Cleaning
The machine, except for the Power Pack and fan motor, can be pressure washed for cleaning. For detailed cleaning instructions, refer to the user guide.
Questions?
If you have any questions or need assistance, contact a Triminator expert at 1-530-265-4277 or email info@thetriminator.com. Additional information can be found at thetriminator.com. You can also follow @THETRIMINATOR on social media for updates.
SAFETY CHECK
- Tumbler is properly seated
- Brush is installed and locked into place
- All guarding is properly installed
- Tumbler cover is properly installed and magnet is aligned with the Power Pack
- Hopper, chute, and filter bags are properly installed
CHECK USER GUIDE FOR DETAILED INSTRUCTIONS
OPERATION
The Hybrid™ is a continuous throughput trimmer that will continually process
product as it’s fed. The machine can process up to 40 lbs per hour (wet) and
15 lbs per hour
(dry) with one trimming unit.
NOTE: Operate the trimmer in a cool, low-humidity environment for the
best results.
START-UP SEQUENCE
- Ensure the lid is seated and the emergency stop is not engaged
- Set vacuum pressure and start the fan motor
- Set speeds and start tumbler and blade motors
ADJUST TILT
Tilt affects the amount of time that product spends in the trimmer.
- Turn knob clockwise to increase tilt
- Turn knob counter-clockwise to decrease tilt
CONTROLS
SUGGESTED START SETTINGS
The Triminator Hybrid™ can trim at almost any moisture content. Knowing your moisture levels can help inform your starting settings
LOAD FLOWER AND FEED THE TUMBLER
Load bucked and destemmed product into the hopper (or infeed conveyor if
applicable). It’s best to keep the tumbler ?/? to ?/? full of material. Too
little material may result in over-trimmed product and too much may result in
poor trim quality due to low vacuum suction.
CHECK AND ADJUST
Check the quality of the trim from your first batch and adjust settings as
needed.
Machine Tilt – Higher tilt moves product through the tumbler faster. Lower
tilt allows the product to spend more time in the tumbler.
Vacuum Suction – Higher pressure pulls leaves closer to the blade. Lower
pressure can reduce over-trimming the product.
Tumbler Speed – Slower speeds allow more cuts per rotation but can result in
product clumping. Higher speeds can result in no product tumbling. Aim for a
tumbling wave of product.
Blade Speed – Faster speeds increase cuts per tumbler rotation.
CHECK USER GUIDE FOR TRIM QUALITY TROUBLESHOOTING
CLEANING
With the exception of the Power Pack and the fan motor, the machine can be
pressure washed.
REFER TO USER GUIDE FOR CLEANING DETAILS
QUESTIONS?
CONTACT A TRIMINATOR EXPERT
1-530-265-4277
INFO@THETRIMINATOR.COM
THETRIMINATOR.COM
@THETRIMINATOR
References
- Cannabis Trimming Machines | Hemp Harvest Equipment | Triminator®
- Triminator Media Kit | Brand Assets, Images and Press Info
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>