Safety Technology International STI-9601 Smoke Detector Wire Guard Instruction Manual
- June 12, 2024
- Safety Technology International
Table of Contents
Safety Technology International STI-9601 Smoke Detector Wire Guard
Product Information
Product Model | Dimensions (inches) |
---|---|
STI-9601 | 8.25 x 2.75 |
STI-9601-SS | 8.25 x 2.75 |
STI-9602 | 8.25 x 4.25 |
STI-9604 | 7 x 3.25 |
STI-9604-SS | 7 x 3.25 |
STI-9605 | 7.125 x 4.5 |
STI-9605-SS | 7.125 x 4.5 |
STI-9609 | 8.25 x 4.6 |
STI-9609-SS | 8.25 x 4.6 |
Product Usage Instructions
- Center the wire guard over the existing smoke detector.
- Mark and drill (4) mounting holes (see pictorial for size). Insert anchor into the ceiling. (Note: If lag shields and lag bolts are used, make sure the anchor is flush with the surface.)
- If using the STI-8170 backplate, insert screws through clamps and backplate (if used) and screw into anchors, but do not tighten.
- Position the guard over the detector, slide clamps onto the top wire of the guard, and tighten the screws.
Service:
- Periodic cleaning of the smoke detector is required to prevent dust and other matter from accumulating.
- To service the smoke sensor unit, loosen but do not remove the (4) screws, rotate clamps, and carefully remove the wire guard.
Optional Accessories:
- KIT-82: #8 x 1 1/2 spanner tamper resistant stainless steel screw kit
- KIT-19038: #8 spanner bit with 5/16 hex drive
- STI-8170: Backplate for use with STI-9601, STI-9602, STI-9609, or STI-9610 cages
Approvals:
- STI-9601, STI-9602, STI-9604, STI-9605: UL Listed No. S3504 for use with Listed low profile smoke detectors
- STI-9609, STI-9610: UL Listed No. S3504 for use with Listed high profile smoke detectors
Warranty:
- Three-year warranty or a one-year limited warranty (from date of purchase) on most products. Visit the website for details.
Note: All specifications and information shown were current as of publication and are subject to change without notice.
Product Model References:
Product Model | Dimensions (inches) |
---|---|
STI-9618 | 4.62 x 5.37 x 3 |
STI-9619 | 7.75 x 5.37 x 5.62 |
STI-9620 | 6.25 x 4 x 2.25 |
STI-9621 | 7 x 5.75 x 4.50 |
STI-9622 | 8.75 x 4 x 3.75 |
STI-9640 | 10.5 x 13.75 x 2.75 |
STI-9740 | 15.5 x 20.5 x 6 |
STI-9742 | 15.59 x 16.09 x 3.30 |
STI-9641 | 19.7 x 14.6 x 4 |
STI-9644 | 8.7 x 17.7 x 5 |
STI-9645 | 13.8 x 21.7 x 5.9 |
STI-9649 | 10.75 x 24.75 x 11.25 |
STI-9703 | 5 x 13.5 x 4 |
STI-9705 | 7.4 x 6.15 x 3.39 |
STI-9708 | 7.49 x 6.74 x 6.09 |
STI-9711 | 8.26 x 8.26 x 3.54 |
STI-9714 | 8.55 x 8.55 x 6.23 |
STI-9717 | 6.1 x 9.3 x 2.4 |
STI-9720 | 6.1 x 9.3 x 4.9 |
STI-9729 | 7 x 7 x 7 |
STI-9730 | 12 x 12 x 12 |
Note: For more information, refer to the electronic warranty form at www.sti-usa.com/wc14.
Regions:
- USA
- EMEA
IMPORTANT
Do not attempt to install the wire guard until the smoke sensor has been
tested and in proper working order according to the manufacturer’s
installation instructions furnished with the sensor unit.
INSTALLATION
-
Center the wire guard over existing smoke detector.
-
Mark and drill (4) mounting holes (see pictorial for size). Insert anchor into ceiling.
NOTE: If lag shields and lag bolts are used, make sure anchor is flush with surface. Position guard, insert lag bolts and tighten. Length of bolt should be selected to assure full thread engagement in anchor. -
STI-8170 BACKPLATE – STI recommends the use of this plate on all unstable mounting surfaces.
-
Insert screws through clamps and backplate (if used) and screw into anchors; but do not tighten.
-
Position guard over detector, slide clamps onto top wire of guard and tighten screws.
SERVICE
- Periodic cleaning of the smoke detector is required so dust and other matter do not accumulate.
- To service the smoke sensor unit, loosen but do not remove the (4) screws rotate clamps and carefully remove wire guard.
OPTIONAL ACCESSORIES
KIT-82 #8 x 1 1/2” spanner tamper resistant stainless steel screw kit.
KIT-19038 #8 spanner bit with 5/16” hex drive.
STI-8170 for use with STI-9601, STI-9602, STI-9609 or STI-9610 cages.
APPROVALS
STI-9601, STI-9602, STI-9604, STI-9605
UL Listed No. S3504 for use with Listed low profile smoke detectors STI-9609,
STI-9610
UL Listed No. S3504 for use with Listed high profile smoke detectors
Three year warranty or a one year limited warranty (from date of purchase) on most products. See website for details. Electronic warranty form at www.sti- usa.com/wc14.
ADDITIONAL WIRE GUARDS
AVAILABLE
Visit www.sti-usa.com/w1 for complete
detailsSMOKE
101075All dimensions are approximate
SMOKE DETECTOR GUARDSPIR
- STI-9601-SS 8.25 x 2.75”
- STI-9602 8.25 x 4.25”
- STI-9604 7 x 3.25”
- STI-9604-SS 7 x 3.25”
- STI-9605 7.125 x 4.5”
- STI-9605-SS 7.125 x 4.5”
- STI-9609 8.25 x 4.6”
- STI-9609-SS 8.25 x 4.6”
PIR GUARDS
- STI-9618 4.62 x 5.37 x 3”
- STI-9619 7.75 x 5.37 x 5.62”
- STI-9620 6.25 x 4 x 2.25”
- STI-9621 7 x 5.75 x 4.50”
- STI-9622 8.75 x 4 x 3.75”
EXIT SIGN WIRE CAGES
- STI-9640 10.5 x 13.75 x 2.75”
- STI-9740 15.5 x 20.5 x 6”
- STI-9742 15.59 x 16.09 x 3.30”
EMERGENCY LIGHT CAGE
- STI-9641 19.7 x 14.6 x 4”
- STI-9644 8.7 x 17.7 x 5”
- STI-9645 13.8 x 21.7 x 5.9”
- STI-9649 10.75 x 24.75 x 11.25”
- STI-9703 5 x 13.5 x 4”
MISCELLANEOUS WIRE CAGES
- 9664STI-9705 7.4 x 6.15 x 3.39”
- STI-9708 7.49 x 6.74 x 6.09”
- STI-9711 8.26 x 8.26 x 3.54”
- STI-9714 8.55 x 8.55 x 6.23”
- STI-9717 6.1 x 9.3 x 2.4”
- STI-9720 6.1 x 9.3 x 4.9”
- STI-9729 7 x 7 x 7”
- STI-9730 12 x 12 x 12
- STI-9731 12 x 12 x 8”
- STI-9732 18 x 15 x 13”
- STI-9880 10.45 x 62.75 x 6.2”
- STI-9881 10.45 x 98.25 x 6.2”
- STI-101075 10 x 10 x (63 to 75)”
- STI-241416 33.25 x 23.29 x 16”
- STI-282121 39.06 x 32.01 x 21.29”
BEAM SMOKE DETECTORS
- STI-9623 7.75 x 6 x 6”
- STI-9624 8.875 x 5.5 x 4.75”
- STI-9706 10.82 x 9.32 x 4”
- STI-9707 11 x 9.62 x 5.5”
- STI-9840 6.61 x 5.78”
- STI-9841 11.52 x 10 x 3.58”
- STI-9845 6.7 x 9.2 x 4.07”
- STI-9846 7.6 x 11.6 x 5.6”
CLOCK BELL WIRE CAGES
- STI-9631-R 10.5” Diameter – Red
- STI-9635 14.25” Diameter
- STI-9636 20.75” Diameter
- STI-9637 26.75” Diameter
BEACON & SOUNDER CAGESS
- STI-9614 7.9 x 6”
- STI-9615 3.7 x 3.5”
- STI-9617 5.9 x 4.9”
- STI-9664 3.86 x 6.18”
- STI-9665 7 x 8.43”
- STI-9750 9.6 x 2.8”
- STI-9754 8.4 x 9.2 x 3.5”
- STI-9760 8.5 x 3.2”
- STI-9761 8.5 x 5.7”
- STI-9762 6.2 x 4.75 x 2.5”
- STI-9763 6.2 x 4.75 x 4”
- STI-9764 6.6 x 6 x 2.5”
- STI-9765 6.6 x 6 x 4.4”
- STI-9766 8.2 x 6.75 x 2.9”
- STI-9767 8.2 x 6.75 x 5”
STI CEILING MOUNTED SMOKE DETECTOR GUARDS
All specifications and information shown were current as of publication and
are subject to change without notice.
www.sti-usa.com
www.sti-emea.com
References
- Home - STI EMEA
- Security & Safety Device Protection | Safety Technology International
- Protective Cages & Wire Guard Shields for Smoke Detectors & Other Alarms
- Warranty & Returns - STI US
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>