Velleman PEM7D Mini Infrared Light Lock User Manual
- June 12, 2024
- Velleman
Table of Contents
PEM7D Mini Infrared Light Lock
User Manual
Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device
after its lifecycle could harm the environment. Do not dispose of the unit (or
batteries) as unsorted municipal waste; it should be taken to a specialized
company for recycling. This device should be returned to your distributor or
to a local recycling service. Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before
bringing this device into service. If the device was damaged in transit, don’t
install or use it and contact your dealer.
The PEM7D is a compact entry and approach warning system for use in shops,
reception areas, private homes, etc. The device consists of a transmitting and
receiving unit that transmits an invisible, modulated beam of IR light across
e.g. a doorway, onto a prismatic reflector mounted across from the
transmitter. This reflects the beam back to the receiver to complete the
protection circuit. The beam is interrupted when a person walks through it,
causing the alarm to trigger and sound an audible warning. The beam is
produced by a LED, which has a much greater lifespan and is less susceptible
to surge and vibration damage than a tungsten filament lamp. The receiver is
only sensitive to the frequency of the modulated light in the beam.
Notes
- It is recommended to use this device indoors. Rain drops and condensation may influence its operation .
Safety Instructions
| Keep the device away from children and unauthorised users.
---|---
| There are no us er-serviceable parts inside the device. Refer to an
authorized dealer for service and/or spare parts.
General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
| Keep this device away form rain, moisture, splashing and dripping liquids.
---|---
| Keep this device away from dust and extreme temperatures.
| Protect this device from shocks and abuse. Avoid brute force when operating
the device.
- Familiar ise yourself with the functions of the device before actually using it.
- All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
- Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
- Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
Overview
Refer to the illustrations on page 2 of this manual.
Connection diagram
- Input
- Adapter DC 12V
- Speaker
- Selector
- Output
- Optional* counter PEM7D/C
- IR beam
- Retro reflector
- Photoelectric beam sensor
- Not incl.
Installation
- Mount the included mounting bracket on a sidewall or another suitable surface at ± 60 cm above the ground.
- Note: make sure passers-by can not accidentally bump into it.
- Attach the sensor [9] to the mounting bracket.
- [A] Connect the sensor [9] to the speaker [3].
- [B] Connect the speaker [3] to the mains using the included adapter [2].
- [C] Set the selector [4] to CHIME.
- [D] Use the included screwdriver to set the timer and volume of the speaker. Do not force or use any other screwdriver.
- [E] Locate the best position for the reflector [8] by moving it against the wall opposite the sensor until the chime stops and the red alignment LED on the senor is on. Distance must be at least 50 cm and maximum 7 m (depends on environmental conditions. Mount the reflector in that location.
- When applicable, connect the counter [6] (optional, not incl.) to the output [5] using the 10 m cable that comes with the counter (PEM7D/C).
Troubleshooting
When problems are encountered, refer to following overview before contacting your local dealer:
- Check that the speaker is set to “CHIME” or “ALARM”. “OFF” = silent.
- Check that the timer and/or volume are not in the “min.” position.
- A red LED indicates proper alignment of the sensor and reflector. If the LED is not lit, realign sensor and reflector. Distance must be at least 50 cm.
- Make sure the adapter is firmly connected to the speaker.
- Make sure the sensor is firmly connected to the input of the speaker.
Technical Specifications
Nominal detection range | 7 m |
---|---|
Light source | IR LED |
Speaker | power supply: DC 9-15V |
speaker output: chime / off / alarm (selection by switch) | |
duration audio signal: about 1 sec. for chime 30 sec. for alarm | |
timer adjustable: 3 – 30 sec. before alarm activation | |
volume adjustable: yes (from 0 to max.) | |
cable length: ± 9.5 m | |
Working temperature | -20 °C to +50 °C |
Power supply | DC 9-15V regulated (adapter included) |
Total current consumption | < 130 mA |
Standby current | 25 mA |
IP rating | IP44 / indoor use |
Use this device with original accessories only. Velleman nv cannot be held
responsible in the event of damage or injury resulting from (incorrect) use of
this device.
For more info concerning this product and the latest version of this manual,
please visit our website www.velleman.eu.
The information in this manual is subject to change without prior notice.
© COPYRIGHT NOTICE
The copyright to this manual is owned by Velleman nv. All worldwide rights
reserved. No part of this manual may be copied, reproduced, translated or
reduced to any electronic medium or otherwise without the prior written
consent of the copyright holder.
Velleman® Service and Quality Warranty
Since its foundation in 1972, Velleman® acquired extensive experience in the
electronics world and currentlydistributes its products in over 85 countries.
All our products fulfil strict quality requirements and legal stipulations in
the EU. In order to ensure the quality, our products regularly go through an
extra quality check, both by an internal quality department and by specialized
external organisations. If, all precautionary measures notwithstanding,
problems should occur, please make appeal to our warranty (see guarantee
conditions).
General Warranty Conditions Concerning Consumer Products (for EU):
- All consumer products are subject to a 24-month warranty on production flaws and defective material as from the original date of purchase.
- Velleman® can decide to replace an article with an equivalent article, or to refund the retail value totally or partially when the complaint is valid and a free repair or replacement of the article is impossible, or if the expenses are out of proportion.
You will be delivered a replacing article or a refund at the value of 100% of the purchase price in case of a flaw occurred in the first year after the date of purchase and delivery, or a replacing article at 50% of the purchase price or a refund at the value of 50% of the retail value in case of a flaw occurred in the second year after the date of purchase and delivery.
• Not covered by warranty:
– all direct or indirect damage caused after delivery to the article (e.g. by
oxidation, shocks, falls, dust, dirt, humidity…), and by the article, as well
as its contents (e.g. data loss), compensation for loss of profits;
– consumable goods, parts or accessories that are subject to an aging process
during normal use, such as batteries (rechargeable, non-rechargeable, built-in
or replaceable), lamps, rubber parts, drive belts… (unlimited list);
– flaws resulting from fire, water damage, lightning, accident, natural
disaster, etc.…;
– flaws caused deliberately, negligently or resulting from improper handling,
negligent maintenance, abusive use or use contrary to the manufacturer’s
instructions;
– damage caused by a commercial, professional or collective use of the article
(the warranty validity will be reduced to six (6) months when the article is
used professionally);
– damage resulting from an inappropriate packing and shipping of the article;
– all damage caused by modification, repair or alteration performed by a third
party without written permission by Velleman®.
- Articles to be repaired must be delivered to your Velleman® dealer, solidly packed (preferably in the original packaging), and be completed with the original receipt of purchase and a clear flaw description.
- Hint: In order to save on cost and time, please reread the manual and check if the flaw is caused by obvious causes prior to presenting the article for repair. Note that returning a non-defective article can also involve handling costs.
- Repairs occurring after warranty expiration are subject to shipping costs.
- The above conditions are without prejudice to all commercial warranties.
The above enumeration is subject to modification according to the article (see article’s manual).
Made in PRC
Imported by Velleman nv
Legen Heirweg 33, 9890 Gavere, Belgium
www.velleman.eu
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>