GSD DCT1LR2601 WiFi and Bluetooth Module User Manual

GSD DCT1LR2601 WiFi and Bluetooth Module

Product Information

• Manufacturer: Hui Zhou Gaoshengda Technology Co., LTD
• Model Number: DCT1LR2601
• Product Name: WIFI+BT Module
• Standard Interface: USB
• Data Transfer Rate: 1, 2, 5.5, 6, 11, 12, 18, 22, 24, 30, 36, 48, 54, 60, 90, 120, and a maximum of 866.7Mbps
• Modulation Method:
  • Bluetooth: GFSK,/4-DQPSK,8DPSK
  • 802.11b: DQPSK,DBPSK,CCK
  • 802.11g: QPSK,BPSK,16QAM,64QAM with OFDM
  • 802.11n: QPSK,BPSK,16QAM,64QAM with OFDM
  • 802.11a: QPSK,BPSK,16QAM,64QAM,256QAM with OFDM
  • 802.11ac: QPSK,BPSK,16QAM,64QAM with OFDM
• Frequency Band:
  • Bluetooth: 2402~2480 MHz
  • WIFI: 2.4GHz and 5GHz
• Operation Mode: Linux, Windows
• Security: Up to 128-Bit WEP Encryption
• Operating Voltage: Not specified
• Current Consumption: Not specified
• Antenna Type:
  • 2.4GHz: PCB antenna1 & 5.73 dBi, PCB antenna2 & 3.94 dBi
  • 5GHz: PCB antenna1 & 5.87 dBi, PCB antenna2 & 5.76 dBi
  • BT Antenna: BRADE ZTX
• Operating Temperature: Not specified
• Storage Temperature: Not specified
• Humidity: 5 to 95% maximum (non-condensing)

Product Usage Instructions

1. Please ensure that this product and its accessories are kept out of reach of children.
2. Avoid splashing water or any other liquid onto the product, as it may cause damage.
3. Do not place the product near a heat source or in direct sunlight to prevent deformation or malfunction.
4. Keep the product away from flammable substances and naked flames.
5. Do not attempt to repair the product yourself. Only qualified personnel should handle repairs.
6. This equipment complies with Part 15 of the FCC Rules. It should not cause harmful interference and must accept any interference received, including interference that may cause undesired operation.
7. The module has been assessed against FCC rule parts CFR 47 FCC Part 15 C (15.247, DTS and DSS) and CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter.
8. The module complies with FCC Part 15.247 / Part 15.407 and applies for Single module approval.
9. Ensure a minimum distance of 20cm between the radiator and your body when installing and operating the equipment to comply with FCC radiation exposure limits for an uncontrolled environment.
10. The antenna types and gains are as follows:
    • 2.4GHz: PCB antenna1 – 5.73 dBi, PCB antenna2 – 3.94 dBi
    • 5GHz: PCB antenna1 – 5.87 dBi, PCB antenna2 – 5.76 dBi
11. Note: WIFI antennas are permanently attached and cannot be replaced.

Product Descrition
The DCT1LR2601 is a complete 2.4GHz/5GHz WIFI 2×2 MIMO module. This module provides a high level of integration with a dual-stream IEEE 802.11ac MAC/ base band /radio and Bluetooth 5.0.The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 866.7Mbps. It fully complies with IEEE 802.11 a/b/g/n/ac feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput from an extended distance.

Product Features

• Complies with IEEE 802.11b/g/n for 2.4GHz，IEEE 802.11a/n/ac or 5GHz
• Bluetooth v5.0
• Two transmit and Two receive path(2T2R)
• Works with all existing network nfrastructure.
• Capable of up to 128-Bit WEP Encryption.
• Freedom to roam while staying connected.
• UP to 866.7 Mbps High-Speed Transfer Rate in 802.11ac mode of operation.
• Operating Systems： Linux, Windows.
• Low power consumption.
• Easy to install and configure.
• High speed usd 2.0 interface.
• ROHS compliant

Product Specification

of 866.7Mbps
Modulation Method| GFSK,π/4-DQPSK,8DPSK(bluetooth) DQPSK,DBPSK,CCK(802.11b) QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n) QPSK,BPSK,16QAM,64QAM with OFDM (802.11a) QPSK,BPSK,16QAM,64QAM,256QAM with OFDM (802.11ac)
Frequency Band| BLUETOOTH 2402~2480 MHz
WIFI
2.4G: 2412~2462 MHz
5G: 5180~5320MHz, 5500~5825MHz
Operation Mode| Infrastructure
Security| WEP, TKIP, AES, WPA, WPA2
Operating Voltage| 3.3V±10%
Current Consumption| ＜1000mA
Antenna Type| PIFA/PCB Antenna
Operating Temperature| 0 ~ 70°C ambient temperature
Storage Temperature| -40 ~ 80°C ambient temperature
Humidity| 5 to 95 % maximum (non-condensing)

NOTICE:

• please keep this product and accessories attached to the places which children can’t touch;
•  do not splash water or other liquid onto this product, otherwise it may cause damage;
• do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
• please keep this product away from flammable or naked flame;
• please do not repair this product by yourself. Only qualified personnel can be repaired.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS and DSS) and CFR 47 FCC Part 15 E (NII). It is applicable to the modular transmitter
• This radio transmitter FCC ID: 2AC23-DCT1L has been approved by Federal Communications Commission to operate with the integrated PCB antenna for 2.4G WIFI&5G WIFI. Use of any other antenna is strictly prohibited without filing an application for a new system-specific FCC ID.

This radio transmitter FCC ID: 2AC23-DCT1L has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
The concrete contents to check are the following three points.

1. Must use an antenna such as PIFA Antenna with a gain not exceeding 1.72 dBi for BT/BLE;
2. Should be installed so that the end user cannot modify the antenna;
3. Feed line should be designed in 50ohm

Fine-tuning of return loss etc. can be performed using a matching network. The antenna shall not be accessible for modification or change by the end user

• The module complies with FCC Part 15.247 / Part 15.407 and applies for Single module approval.
• Trace antenna designs: Not applicable – the antenna is integrated into the module and cannot be modified. See section 2.3.
• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• Antenna type and antenna gain:

Note: WIFI Antennas are permanently attached and can’t be replaced.

BT Antenna:

• Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: 2AC23-DCT1L” Any similar wording that expresses the same meaning may be used.

• Testing of the host product with all the transmitters installed – referred to as the composite investigation test- is recommended, to verify that the host product meets all the applicable FCC rules. The radio spectrum is to be investigated with all the transmitters in the final host product functioning to determine that no emissions exceed the highest limit permitted for any one individual transmitter as required by Section 2.947(f). The host manufacturer is responsible to ensure that when their product operates as intended it does not have any emissions present that are out of compliance that were not present when the transmitters were tested individually.
  If the modular transmitter has been fully tested by the module grantee on the required number of channels, modulation types, and modes, it should not be necessary for the host installer to re-test all the available transmitter modes or settings. It is recommended that the host product manufacturer, installing the modular transmitter, perform some investigative measurements to confirm that the resulting composite system does not exceed the spurious emissions limits or band edge limits (e.g., where a different antenna may be causing additional emissions). The testing should check for emissions that may occur due to the intermixing of emissions with the other transmitters, digital circuitry, or due to physical properties of the host product (enclosure). This investigation is especially important when integrating multiple modular transmitters where the certification is based on testing each of them in a stand-alone configuration.

• Any company of the host device which install this modular should perform the test of radiated & condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. The host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

• The host manufacture is recommended to use D04 Module Integration Guide recommending as “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties.

• This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.

Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 12290A-DCT1L” any similar wording that expresses the same meaning may be used.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
This radio transmitter IC: 12290A-DCT1L has been approved by Innovation, Science, and Economic Development Canada to operate with the integrated PCB antenna for 2.4G WIFI&5G WIFI. Use of any other antenna is strictly prohibited without filing an application for a new system-specific IC ID.
This radio transmitter [IC: 12290A-DCT1L] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points.

1. Must use an antenna such as IPEX Antenna with a gain not exceeding 1.72 dBi for BT&BLE;
2. Should be installed so that the end user cannot modify the antenna;
3.  Feed line should be designed in 50ohm

Fine-tuning of return loss etc. can be performed using a matching network.

Antenna type and antenna gain:

Note: WIFI Antennas are permanently attached and can’t be replaced.

BT Antenna:

Notice to OEM integrator

Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/ICanada statement).
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. Any company of the host device which install this modular should perform the test of radiated & conducted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247 and 15.407) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AC23-DCT1L or IC: 12290A-DCT1L. Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC ID and only hosts going into Canada can use the IC ID.

Installer should put it in the manual：
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>