Elitech STC-1000Pro TH Intelligent Temperature and Humidity Controller User Manual

June 12, 2024
Elitech

Elitech Logo STC-1000Pro TH / STC-1000WiFi TH
Intelligent Temperature and Humidity ControllerElitech STC 1000Pro TH
Intelligent Temperature and Humidity Controller 

Introduction

STC-1000Pro TH / STC-I000WIFi TH is an integrated plug-and-play temperature and humidity controller. It has temperature and humidity integrated probe and is pre-connected to two output sockets to control temperature and humidity simultaneously.
The large LCD screen intuitively displays temperature, humidity, and other parameters. With the three-key design, it enables quick parameter setting, such as alarm limit, calibration, protection time, unit switching, etc.
It is mainly used in aquarium, pet breeding, incubation, seedling mat, greenhouse, and other application scenarios.

Overview

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller -
Overveiw

2.1 Display Introduction
Please check the instructions below before parameter configuration.

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller -
Overveiw 1

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller -
Overveiw2

2.2 Parameter Table

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller -
Peramitar

S/N| Code| Function| Setting range| Default value| Temperature related parameters
---|---|---|---|---|---
1| TCH| Temperature cooling/heating mode selection| C / H| C
2| TS| Temperature set value| -5 70°C| 25
23 -158°F| 75
3| TD| Temperature differential| 0.2 – 15°C| 2
1- 30`F| 3
4| TPT| Temperature protection time| 0-10  Min| 3
rn| TAH| Temperature alarm high limit| -5 – 70°C| 35
23 -158LF| 95
6| TAL| Temperature alarm low limit| -5 – 70°C| 0
23 – 158’F| 32
7| TCA| Temperature calibration| -10 – 10°C| 0
-15 -15°F| 0
8| CF| Temperature unit| C / F|
S/N| Code| Function| Setting range| Default value| Humidity related parameters
---|---|---|---|---|---
9| HDH| Dehumidifying/ Humidifying
mode selection| H / D| H
10| HS| Humidity set value| 5 – 99WoRH| 50
11| HD| Humidity differential ff| 1 – 30970RH| 5
12| HPT| Humidity protection time| 0 – 10 Min| 3
13| HAH| Humidity alarm high limit| 5 – 99°/0172H| 99
14| HAL| Humidity alarm low limit| 5 – 99%RH| S
15| HCA| Humidity calibration| -10 -10WoRH| 0
16| COT| Continuous operating time| 0 – 999 Min| 30
17| BL| Backlight time| 0 – 999 Min| 30|

Table 2
2 The default temperature unit for US version is °F, while the UK and European version is °C.
2.3 Button Operation

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller -
Overveiw 3

Operation

Important: Improper use of the product may cause injury or product damage. Please read, understand and follow the operating steps below.
3.1Sensor Installation
Plug the sensor fully into the headphone jack from the button of the main controller.

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller -
Sensor

3.2 Power-on
Please insert the power plug into the power socket to power on the controller (within the range of 100-240VAC)
The screen will light up and display the temperature, humidity, and other readings.

3.3 Parameter Setting
Press and hold button for 3 seconds to enter the parameter setting mode, the buzzer will beep, and the LCD will display icon.
In the menu setting, press button and the Tsv* parameter light will be on o flashes. When it is flashing, press or button to switch to the next parameter; when the parameter light is on, press or button to increase or decrease the setting value.
In the menu setting, press and hold button for 3 seconds to save settings and exit; or the controller will save and exit setting mode after 30 seconds of idle.
The Tsv displays temperature-related parameters and Hsv displays humidity- related parameters.
For example, set TS and TD parameters into TS = 20°C and TD = 5°C respectively.as shown in Fig. 6.

  1. Press button and release after the buzzer beeps (about 3 seconds);
  2. Press [¥) button, and the parameter code will display TS;
  3. Press button, and will flash, indicates TS parameter is ready to besset;
  4. Press (or press and hold) button to change the value to 20;
  5. Press button, and TPV will appear;
  6. Press button, and the parameter code will display TD;
  7. Press button, and TPV will flash,indicates TD parameter is ready o be set;
  8. Press (or press and hold) button to change the value to 5;
  9. Press button and release after the buzzer beeps (about 3 seconds) to exit the parameter setting.

Note: 252 Dotted-line in the figure shows the numbers are flashing (ready for setting); 50 solid-line shows the numbers stop flashing (value is set).
See the flow chart below to change other parameter values one by one. as shown in Fig. 7.

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller -
Key

Function Description

4.1 Temperature Setting – TCH, TS, TD
Cooling mode (TCH = C)
When Tev (temperature-present value) is higher than TS + TD (temperature-set value + temperature differential), will appear, workl will be turned on, and cooling will begin;
When Tev (temperature-present value) s lower than TS (temperature set value), % willdisappear, world will be tumed off, and cooling will stop. For example: TS = 15°C, TD = 5°C, as shownin Fig.8.

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller -
Fig

Heating mode (TCH = H)
When Tev (temperature-present value) is lower than TS – TD (temperature-set value – temperature differential), will appear, workl will be turned on, and heating will begin;
When Tev (temperature – present value) is higher than TS (temperature -set value), will disappear, workl will be tumed off, and heating will stop. For example: TS = 15°C, TD = 5°C, as showniin Fig. 9.

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller - Fig
1

4.2 Temperature Protection Time – TPT
WORK1 is a temperature socket and the time interval from its power-off to power-on again should meet the time requirement for TPT. If not, or 5 will flash. This protection time requirement should also be satisfied when the controller s just powered on.
4.3 Temperature Alarm Limit- TAH, TAL
When Tev (temperature-present value) is higher than TAH (temperature alarm highlimit), the temperature alarm high limit will be triggered and code will be displayed;
When Tev (temperature-present value) is lower than TAL (temperature alarm low limit), the temperature alarm low limit will be triggered and ELL code will be displayed;
During the alarm, the buzzer makes a sound of “bi-bi-Biii” until the temperature is back to the normal temperature range; or press any button to mute the alarm.
During the temperature alarm limit, the output of WORK1 socket is not affected
4.3 Temperature Alarm Limit- TAH, TAL
When Tev (temperature-present value) is higher than TAH (temperature alarm highlimit), the temperature alarm high limit will be triggered and EtH code will be displayed;
When Tev (temperature-present value) is lower than TAL (temperature alarm low limit), the temperature alarm low limit will be triggered and ELL code will be displayed;
During the alarm, the buzzer makes a sound of “bi-bi-Biii” until the temperature is back to the normal temperature range; or press any button to mute the alarm.
During the temperature alarm limit, the output of WORK1 socket is not affected
4.4 Temperature Calibration – TCA
The temperature can be calibrated if the temperature-present value deviates from the actual temperature.
Tev (temperature – present value after calibration) = Tev (temperature – present value before calibration) + TCA (temperature calibrated value).
4.5 Temperature Unit – CF
The temperature unit can be switched between Celsius and Fahrenheit.
The temperature related parameter values will be restored to factory default values after the temperature unit is changed.
4.6 Humidity Settings – HDH, HS, HD
Dehumidifying mode (HDH = D)
When Hev (humidity-present value) is higher than HS + HD (humidity set value + humidity differential), will appear, work2 will be turned on, and Dehumidifying will begin;
When Hev (humidity-present value) is lower than HS (humidity set value),will disappear, work2 will be tumed off, and dehumidifying will stop. For example: HS = 50% RH, HD = 10%
RH, as shown in Fig. 10.

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller - Fig
2

Humidifying Mode (TCH = H)
When Hey (humidity-present value) is lower than HS-HD (humidity set value – humidity differential), will appear, work2 will be turned on, and Humidifying will begin;
When Hev (humidity-present value) is higher than HS (humidity set value), will appear, work2 will be turned off, and humidifying will stop. Forexample: HS = 50%RH, HD = 109%RH, as shown in Fig. T

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller - Fig
3

4.7 Humidity Protection Delay – HPT
WORK2 is a humidity socket and the time interval from its power-off to power- on again should meet the time requirement for HPT. If not, or light will flash
This protection time requirement should also be satisfied when the controller s just powered on.
4.8 Humidity Alarm High Limit – HAH, HAL
When Hev (humidity-present value) is higher than HAH (humidity alarm high limit), the humidity alarm high limit will be triggered and EHH code will be displayed;
When Hev (humidity-present value) is lower than HAL (humidity alarm lower limit), the humidity alarm lower limit will be triggered and EHL code will be displayed;
During the alarm, the buzzer makes a sound of “bi-bi-Biii” until the hurmidity is back to the normal humidity range; or press any button to mute the alarm. During the humidity alarm high limit, the output of WORK2 socket is not affected.
4.9 Humidity Calibration – HCA
The humidity can be calibrated if the humidity-present value deviates from the actual humidity.
Hev (humidity-present value after calibration) = Hev (humidity-present value before calibration) + HCA (humidity calibrated value).
4.10 Continuous Operating Time – COT
During humidity control, when COT+0 and output conditions are met, WORK2 socket will work in on-off-on-off…. mode. COT is time on as well as time off. eg, if COT=10, the WORK2 output socket will turn on for 10 minutes and off for 10 minutes, then repeat.
When COT = 0 and output conditions are met, WORK2 output socket will not be affected by COT.
4.11 Backlight Time – BL
BLis the screen display time. When BL=0 indicates display is always on.

Equipment Installation

As a safety precaution, it is recommended to power on the equipment after the installation is completed.
The only installation method is by hanging the equipment. Please check the installation distance and screw size according to its application scenario before installation.
The schematic diagram of equipment installation is shown below:

Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller - Fig
4

Alarm

In the following circumstances during operation, the buzzer will give a “bi- bi-Biii” alarm, and at the same time, the alarm symbol # on the screen will appear. Press any button to mute the alarm.

S/N Code Function Socket output status
1 Erp Sensorfailure Outputs terminated
2 EEH Temperature alarm high Outputs unchanged
3 FLL Temperature alarmlowlimit Outputs unchanged
4 EHH Humidityalarm high limit Outputs unchanged
5 EHL Humidity alarm low limit Outputs unchanged

Restore Operation Function

7.1 Restore Factory Settings
When the controller is powered on and in non-setting parameter status, please press  buttons simultaneously on the main controller and release until the screen tums off automatically. Wait for the equipment to restart automatically and restore to factory settings.
7.2 Restore Wiletworlk Settings (for STC-1000WiFi TH)
If you would like to reconfigure to a new Wi-Fi network, please keep the equipment in power-on status, press buttons and release when the symbol on the screen flashes. The icon will disappear after the network restoration is completed Please do not power off the equipment during the restoration process.

Access to Network (for STC-1000WiFi TH)

STC-1000WiFi TH features a built-in Wi-Fi module that allows you to remotely view and configure it on the app.
8.1Before you begin, please make sure:
The device supports 2.4G Wi-Fi.(5G Wi-Fi is not compatible.)
The device is in a good and stable Wi-Fi network environment.
Search Elitech in the App Store, download and install the app.
8.2 Connect the device to Elitech app

  1. Find the QR code label on the device. (It shows QR code and 20 numbers)
  2. Power on the device.
  3. Log in your Elitech account (Register an Elitech account)Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller - App
  4. Click the sign + on top right and add device.
  5. Click the sign on top right / Scan the OR code on the label,or manually type in 20 GUID numbers. Enter the device name that your prefer, and click Add.
  6. A window will pop up “The device scanned is a Wi-Fi device. Would you like to set Wi-Fi?”Click OK.Elitech STC 1000Pro TH Intelligent Temperature and Humidity Controller - App 3
  7. Enter Wi-Fi password, click OK, and wait until the operation finishes. The whole process takes about 10 seconds. It exits configuration interface after the network is connected successfuly.
    The main interface displays the device is online. Meanwhile, the sign shows on top of the screen.Elitech STC 1000Pro TH Intelligent Temperature and
Humidity Controller - App 4

Note: The device allows Wi-Fi to be configured within 30 minutes after power on. After 30 minutes, it needs to be powered off for a restart. Or you may refer to 7.2 Restore Wi-Fi Network Settings.

Technical Parameters

Working voltage: 100~240VAC, 50/60Hz
Temperature measurement range: -5~70°C / 23~158°F
Temperature control range: -5~70°C / 23~158°F
Temperature measurement accuracy: £0.5°C /+1°F
Temperature resolution: 0.1°C /0.1°F
Humidity measurement range: 5~99%RH
Humidity control range: 5~99%RH
Humidity measurement accuracy: +5%RH
Humidity resolution: 0.1%RH
Relay contact output capacity: 10A (resistive) / 100 ~ 240VAC
Output power: 2200W (resistive) in total/
200W (inductive) per channel @220VAC,
T100W (resistive) in total/
100W (inductive) per channel @110VAC
Total power consumption: <5W
Working environment temperature: 0°C~60°C / 32-140°F
Storage temperature: -10°C~70°C / 14~140°F
Length of power probe: 1.5m
Length of output power probe: 0.3m
Enclosure size: 165 x 60 x 32 mm
Length of sensor cable: 2m (including probe length)
Best viewing angle of LCD screen: 6 O’clock direction
‘Wi-Fi type*: 2.4G (not support 5G)
*Only for STC-1000WiFi TH

Elitech LogoElitech STC 1000Pro TH Intelligent Temperature and Humidity
Controller - Icon 18 MADE
IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals