ELFA 7315496039803 Freestanding Click-In System Instruction Manual

ELFA 7315496039803 Freestanding Click-In System

Product Information

The product is a freestanding click-in system that can be used as a room divider or for storage purposes. It consists of upright standards, feet, stabilization bars, and optional wire shelves. The system can be assembled as a single-sided solution or a double-sided solution by adding additional sections.

Product Usage Instructions

Assembling a Single-Sided Solution

1. Start by mounting the feet. Screw a plain foot into the foot for freestanding upright.
2. If you want to increase the height, attach a foot height extender first and then screw the foot into the extender.
3. Choose the desired solution height by adjusting how deep you screw the foot into the extender.
4. Insert the uprights into the feet. The bottom of the upright is the part with the small holes on the side.
5. Secure the thicker stabilization bar between the uprights using a mallet. Ensure they are completely in place by tapping alternately on the left and right-hand sides.
6. Press down and knock the upright into the slot of the foot using a mallet. Make sure the upright goes all the way down.
7. Repeat the process with the second foot and upright.
8. Mount your desired storage functions or proceed to Part Two for a double-sided solution.

Adding a Section and Assembling a Double-Sided Solution:

1. Assemble the foot to the upright in the same way as for a single-sided solution.
2. Slide in and mount the backside foot with a leveller.
3. Attach the stabilization bars in the hole.
4. Twist out the added upright so that the stabilization bars lock.
5. Place the end caps (and center caps if applicable) on top of the uprights.
6. Repeat with the second upright.
7. Attach the stabilization bars in an X shape, with the upright sections placed as a T.
8. Twist to make the two uprights/feet parallel.
9. If adding a wire shelf at the bottom, use the provided clips to attach the shelf on the front and back of the foot.

Remember to finetune the height of the feet using the included wrench to ensure your system is level.

MOUNTING INSTRUCTION
FREESTANDING CLICK-IN SYSTEM (PART ONE)
SINGLE-SIDED SOLUTION

• Freestanding is one of the mounting options with-in the Click-in system.
• This option is ideal when you can’t – or don’t want to mount your system directly on the wall e.g. when the wall can’t carry the weight, there is a window or when you want to
• You need the following to assemble your solution:
  • Mallet
• leave the wall as it is. It’s also perfect as a room di-vider, since the upright standards are double-sided.
• Complement with the features you need for storage to fit e.g. clothing, garage or laundry room.

ASSEMBLING A SINGLE-SIDED SOLUTION

• Start by mounting the feet.

• Either a plain foot: screw into the

• Foot for freestanding upright
  

• Foot height extender

• If you have chosen a foot height extender: Attach the extender first and then screw the foot into the extender.

• You can choose the desired solution height, depending on how deep you screw the foot into the extender

• Now insert the Uprights into the feet. The bottom of the upright is the part with the small holes on the side of the upright.

• Using a mallet, press down and knock the upright into the slot of the foot. Make sure the upright goes all the way down.

• Repeat the process with the second foot/upright.

Stabilization bars

• Place the two pieces on the floor and insert the Stabilization bars in an “X” – using the holes on the sides of the uprights.
• Turn up the upright pieces, using one hand – where the other fixates the stabilization bars.
• Stand the unit upright.
• Place the unit towards the wall – no more than 75 mm from the wall.
• Secure the thicker stabilization bar between the uprights, using the mallet, ensuring they are completely into place. Alternate tapping the left and the right hand side.
• Place the two pieces on the floor and insert the Stabilization bars in an “X” – using the holes on the sides of the uprights.

Go on mounting your storage funtions.

• Otherwise follow the steps in part two adding an additional section and to make the solution double-sided.

ADDING AN ADDITIONAL SECTION

• Repeat the process with feet and upright – and then place the additional upright with the front of the feet facing the current section.
• Attach the stabilization bars in the hole.
• Place the end caps (and center caps if you have more than one section) on top of the uprights.
• Twist out the added upright so that the stabilization bars lock.

ASSEMBLING A DOUBLE-SIDED SOLUTION

• Assemble the foot to the upright (in the same way like for a single-sided solution)

• Then slide in and mount the “backside” foot with a leveller.

• Repeat with the second upright.

• Then attach the stabilization bars in an “X”, with the upright sections placed as a “T”.

• Then twist to make the two uprights/feet parallel.

BOTTOM WIRE SHELF
If you are adding a Wire shelf at the bottom (on top of the foot), use the special designed clips to attach the shelf on front and back.

REMEMBER TO FINETUNE

• Make sure to finetune the height of the feet (with the included wrench) in order to have your system level.

© 2022 Elfa International AB. L Nygatan 7, SE-211 38 Malmö, Sweden. All rights reserved. Art. nr 1234567. Ver. 1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>