ads-tec IRF3000 Series Industrial Router and Firewall User Guide
- June 12, 2024
- ads-tec
Table of Contents
**ads-tec IRF3000 Series Industrial Router and Firewall User Guide
**
Safety
ATTENTION
Personal injuries and damage to property through improper use All installation
and service work performed on the device must be performed only under safe,
secure and de-energised conditions!
Note:
Always adhere to the safety measures applicable when handling components at
risk of being damaged by electrostatic discharges in accordance with EN
61340-5-1/-2.
Scope of delivery
- 1 x Industrial router and firewall, type IRF3xxx
- 1 x 4-pin plug for power supply
- 1 x 3-pin plug for Modbus RTU
- 1 x 4-pin plug (grey) for digital I/O #2
- Only with IRF38: 1 x 8-pin plug for digital I/Os #3…5
- 1 x Quick-start guide (this document)
- Optional: 2 x Mobile communications antenna
- Optional accessory: 1 x VESA holder
Optional: Inserting SIM card / smart card / microSD
SIM cards and smart cards (SC) in the ID-000 format as defined in ISO 7816 (25×15 mm) can be used. The SIM card for mobile communications must be inserted into the bottom slot (SIM1). The smart card is intended for backing up the configuration data or for connecting to Big-LinX and must be inserted into the top slot (SC/SIM2). You can insert a microSD card with up to 2048 GB as a memory expansion into the left slot.
- Insert the cards the right way round as shown in the figure.
Assembly
Attaching to top-hat rail
- Position the IRF on the top-hat rail from below at an angle (1).
- Pull the top-hat rail locking mechanism (2) upwards using a screwdriver, push the device onto the upper side of the top-hat rail and remove the screwdriver.
- The top-hat rail locking mechanism springs back to its original position.
- Check that the IRF is seated securely on the top-hat rail.
Detaching from top-hat rail
To detach the IRF from the top-hat rail, pull the top-hat rail locking
mechanism (2) upwards using a screwdriver and remove the device downwards at
an angle.
Optional accessory: Attaching the VESA holder
Screw the mounting plate directly onto the device label using the screws
provided. The positions of the screw holes are marked with target crosses ( )
on the label.
Optional: Attaching antennas
Screw the mobile communications antennas to the antenna connections directly
or via SMA extension cables. Only with IRF38: GNSS = connection for a GPS
antenna
Installation
Modbus RTU (RS-485) (electrically isolated)
Electrical bus load: 1/8 unit load; impedance: 96 kΩ.
GND Reference potential (common) for the data signals
D- Inverted data signal
D+ Non-inverted data signal
Digital I/O #2 (electrically isolated)
V+ Supply voltage +24 VDC ± 20 %
DI2 Digital input #2
DO2 Digital output #2, max. 0.5 A
GND Reference potential
Power supply of the device and digital input #1
DI Digital Input #1: +24 VDC ± 20 % Reference potential is 0V of the
device.
FE Functional earth (required for EMC)
0V Reference potential
V+ Supply voltage +24 VDC ± 20 %
Only IRF38xx: Digital I/Os 3…5 (electrically isolated)
V+ Supply voltage +10…30 VDC
DIx Digital inputs #3…5
DOx Digital outputs #3…5, together max. 1.5 A
GND Reference potentia
Commissioning
Connecting IRF to PC
During initial setup, the IRF must be connected to a PC. Connect the
connection ETH2 of the IRF to your PC using a patch cable.
Configuring LAN network adapter of your PC
Open the Properties of the used network adapter and enter the following
parameters:
IP address: 192.168.0.100
Subnet mask: 255.255.255.0 (or, depending on the OS: “24”)
The last number of the IP address must be a number between 1 and 255, e.g. “100”.
Calling web interface of IRF
To access and open the device web interface, start up your web browser. Enter
the following IP address in the address field of the browser:
http://192.168.0.254
Confirm your entry. Then, enter the default log-in details:
User name: admin
Password: admin
The web interface of the device opens. Follow the instructions of the setup wizard.
Further information as well as accessories can be found on our website www .ads-tec.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>