SEALEY TC904 Litre Bead Seating Tool Owner’s Manual

: June 4, 2024
: SEALEY

Table of Contents

TC904 Litre Bead Seating Tool
SAFETY
INTRODUCTION
SPECIFICATION
OPERATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEAD SEATING TOOL 19ltr – PUSH BUTTON
TRIGGER
MODEL NO: TC904

TC904 Litre Bead Seating Tool

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT IS CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

Ensure the bead seating tool is in good condition before use.
Before carrying out maintenance on the unit ensure that the pressure has been vented.
Use only authorized attachments and parts. Unauthorized items may be dangerous and will invalidate your warranty.
Keep the work area clean and tidy.
Ensure the working area is well-lit.
Always wear safety glasses and ear defenders when using the bead seater.
Keep children and unauthorized persons away from the working area.
WARNING: DO NOT discharge unless the nozzle is positioned on the wheel rim.
DO NOT use the bead seater to perform a task for which it is not designed.
DO NOT deface, or remove, the certification plate attached to the bead seater.
DANGER! DO NOT direct compressed air toward people or animals.
WARNING! The bead seater is a pressure vessel and the following safety measures apply:
DO NOT use the bead seater without the safety valve fitted.
DO NOT tamper with the safety valve, DO NOT modify or alter the bead seater in any way, and DO NOT strap anything to it.
DO NOT subject the bead seater to impact, vibration or heat, and DO NOT allow contact with abrasives or corrosives.
Drain condensation from bead seater daily, inspect inside walls for corrosion every three months and have a detailed inspection carried
out annually. The bead seater shell must not fall below the certified thickness at any point.
WARNING! The warnings cautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors that cannot be built into this product but must be applied by the operator.

INTRODUCTION

The easy and instant way to seat tubeless tyre beads. Dumps air into tyre void forcing bead to seat against the rim for inflation. Air release is controlled by a diaphragm valve and push-button trigger. Features slotted key to preventing accidental operation of the trigger. Fully certified tank with gauge and safety valve prevent over-pressurising. Suitable for use on cars, commercials, agricultural and ATV tyres.

SPECIFICATION

Model No:…………………………………………………………. TC904
Maximum Pressure: ……………………………….. 150psi(10.4bar)
Tank Capacity: ………………………………………………………. 19ltr SEALEY TC904 Litre Bead Seating
Tool

OPERATION

4.1.Charging
4.1.1. The air inlet (fig.1) is fitted with a 1/4″BSP female connection.
4.1.2. Connect via an appropriate fitting to an airline.
4.1.3. Open the airline and the air cock on the inlet fitting.
4.1.4. Fill the air reservoir to airline pressure (150psi maximum) and close the inlet connector cock.
4.1.5. Close the cock on the airline and disconnect.
4.2.Using the seating tool in the horizontal position
4.2.1. Adjust the barrel, so that the barrel flange is on the top (FIG.3).
4.2.2. Ensure that both beads of the tyre have been well lubricated and position the wheel on a stand, the valve stem should be pointing upwards and the wheel should be off the ground and the lower bead should be already seated.
4.2.3. Attach an airline to the valve stem to simultaneously assist in the inflation process.
4.2.4. Position the bead seater so that the weight of the unit is supported, and rest the barrel flange on the rim of the wheel directly (fig.3) opposite the valve stem. Attach an airline to the valve stem to simultaneously assist in the inflation process.
4.2.5. Before use, the safety key should be removed from behind the trigger button (fig.2).
4.2.6. The bead seater should be positioned at an angle of between 50 and 70 degrees so that the barrel is pointing directly into the largest gap between the tyre and the wheel.
4.2.7. Holding the bead seater securely with one hand and keeping it steady against the wheel, press the trigger button to release the stored air, and withdraw the nozzle from the bead/tyre interface.
4.2.8. If the bead does not seat, recharge the tank to a higher pressure and repeat the procedure.
NOTE: Once the bead has been set; if required, move the wheel into a tyre cage and inflate to the manufacturer’s recommended pressure.

4.3Using the Bead Seater in the upright position (truck tyres only).
4.3.1Adjust the barrel, so that the barrel flange is on the bottom.
4.3.2Position the wheel against a wall or a solid prop. Make sure that the valve stem is at the bottom and facing towards you.
4.3.3Attach an airline to the valve stem to simultaneously assist in the inflation process.
4.3.4The bead seater should be positioned at an angle of between 50 and 70 degrees so that the barrel is pointing directly into the largest gap between the tyre and the wheel.
4.3.5Holding the bead seater securely with one hand and keep it steady against the wheel, remove the safety key and press the trigger to release the stored air.
4.3.6. If the bead does not seat, recharge the tank to a higher pressure and repeat the procedure.
NOTE: Once the bead has been set, if required, move the wheel into a tyre cage and inflate to the manufacturer’s recommended pressure. If the bead does not seat, recharge the tank to a higher pressure and repeat the procedure.
WARNING! Always wear the personal safety equipment as stated in section 1.1 whilst using this product.
Parts support is available for this product. Please email sales@sealey.co.uk or telephone 01284 757500
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk