Shelly ALT-18793 H and T USB Adapter User Guide
- June 12, 2024
- Shelly
Table of Contents
Shelly ALT-18793 H and T USB Adapter
Product Information
- Product Name: Shelly H&T USB Adapter
- Model: Not specified
- Manufacturer: Not specified
- Compatibility: USB devices
Specifications
- Dimensions: Not specified
- Weight: Not specified
- Color: Not specified
- Power Input: USB
- Power Output: Not specified
Product Usage Instructions
- Ensure that the USB adapter is compatible with your device.
- Read the user manual and safety guide before use.
- Connect the USB adapter to a suitable USB port on your device.
- Ensure that the USB adapter is securely connected.
- Once connected, the USB adapter will provide power to the device.
- If necessary, refer to the installation instructions for any additional setup steps.
Note:
The specific usage instructions may vary depending on the device and its compatibility with the Shelly H&T USB Adapter. Please refer to the user manual provided with your device for detailed instructions.
USER AND SAFETY GUIDE SHELLY H&T USB ADAPTER
Read before use
This document contains important technical and safety information about the
device, its safety use and installation.
CAUTION! Before beginning the installation, please read carefully and entirely this guide and any other documents accompanying the device. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of law or refusal of legal and/or commercial guarantee (if any). Allterco Robotics EOOD is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.
Installation Instructions
Shelly H&T USB Adapter (the Device) provides the option to power supply Shelly H&T using a standard 5 V power adapter with a Micro B USB cable.
- CAUTION! Use only power adapters that comply with the USB standards. Do not power supply the Device if the power adapter or the USB cable are damaged.
- CAUTION! Keep device away from liquids and moisture. The device shouldn’t be used in places with high humidity.
- CAUTION! Do not use the Device If it is damaged!
- CAUTION! Do not attempt to service or repair the Device yourself!
- Remove the Shelly H&T bottom shell by turning it counter-clockwise as shown on fig. 1.
- Replace the bottom shell with the Device.
- ATTENTION! Align the hole (A) in the Device shell with the Shelly H&T control button (B) as shown on fig. 2.
- Attach the Device to Shelly H&T by turning it clockwise as shown on fig.3.
- Plug the power adapter to the Device USB port as shown on fig. 4.
- Use a pin if you want to press the control button through the Device plastic shell. Removing the Helly H&T Adapter will power off the Shelly H&T.
Specifications
- Power supply: 5 V Micro B USB adapter (not included)
- Dimensions: 46x46x17 mm / 1.81×1.81×0.67 in
- Working temperature: -10 °C to 50 °C / 14 °F to 122 °F
- Humidity 30 % to 90 % RH (non-condensing)
- Max. altitude 2000 m / 6,562 ft
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the equipment type Shelly H&T USB
Adapter is in compliance with Directive 2014/30/ЕU, 2014/35/EU, 2011/65/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
shelly.link/ht-adapter_DoC
Manufacturer: Allterco Robotics EOOD
Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria
Tel.: +359 2 988 7435
E-mail: [email protected]
Official website: https://www.shelly.cloud
Changes in the contact information data are published by the Manufacturer on
the official website.
All rights to the trademark Shelly® and other intellectual rights associated
with this Device belong to Allterco Robot-ics EOOD.