APERA INSTRUMENTS LabSen 851-H pH Electrode for Strong Alkaline and Viscous Solutions User Manual

APERA INSTRUMENTS LabSen 851-H pH Electrode for Strong Alkaline and

Viscous Solutions

Product Information

The product is a temperature measuring device with the following features:

• Measuring Range: [Insert Measuring Range]
• Temperature Range: [Insert Temperature Range]
• Body Material: [Insert Body Material]
• Reference Junction: [Insert Reference Junction]
• Membrane Type: [Insert Membrane Type]
• Membrane Resistance: [Insert Membrane Resistance]
• Reference Solution: [Insert Reference Solution]
• Soaking Solution: [Insert Soaking Solution]
• Electrode Dimension: [Insert Electrode Dimension]
• Connector Cable: [Insert Connector Cable]

Product Usage Instructions

To use the product, follow these steps:

1. First, ensure that the device is properly connected to a power source or battery.
2. Next, turn on the device using the power button or switch.
3. Determine the desired measuring range and temperature range for your application.
4. Prepare the reference solution and soaking solution as specified in the user manual.
5. Ensure the membrane type and membrane resistance are suitable for your specific needs.
6. Adjust the electrode dimension according to the size of the sample being measured.
7. Connect the device to the sample using the provided connector cable.
8. Place the electrode in the sample and wait for the device to stabilize.
9. Read and record the temperature displayed on the device.
10. Clean and store the device according to the recommended guidelines in the user manual.

For more detailed instructions, refer to the User Manual provided with the product.

LabSen® pH electrodes are made with proprietary sensor technologies and key components from Switzerland. LabSen® 851-H pH electrode is designed for high- accuracy pH measurement of strong alkaline and highly viscous solutions.

Features

• The sturdy HA membrane is made for strong alkaline and high temperature solutions.
• The pre-pressurized structure allows the electrolyte to stably flow out even in highly viscous samples so as to ensure reliable measurements.
• Blue gel inner solution – does not flow and will not generate air bubbles.

Technical Specifications

How to use

1. Connect the electrode to the BNC connector of your pH meter.
2. Before measuring, twist off the storage bottle cap (see graph on the right), pull out the electrode and rinse it off with distilled or deionized water.
3. Perform at least a two-point calibration before measuring after connecting the new electrode to your pH meter.
4. After using, put the electrode back into the storage bottle and twist on the bottle cap.

Maintenance

1. When not in use, the electrode should be soaked in the storage bottle containing 3M KCL soaking solution to keep the glass membrane and junction in a healthy condition. Clean the bottle and replace the soaking solution if it gets contaminated. The electrode should never be stored in pure water such as deionized or distilled water.
2. The electrode is only as accurate as it is clean. Always thoroughly rinse off the probe before and after each measurement with pure water in a container or with a wash bottle.
3. For tough contaminants, soak the electrode in Apera cleaning solution (AI1166) for 30 minutes. Then use a soft brush to remove the contaminants. Afterwards, soak the electrode in 3M KCL soaking solution for at least 1 hour. Rinse it off, then re-calibrate it before using again.
4. The connector of the electrode should be kept clean and dry. If contaminated, please clean it with medical cotton and isopropyl alcohol and blow-dry it to prevent short circuit of the electrode or slow response of the electrode.
5. The electrode should avoid testing strong acid as well as dehydrating media such as absolute ethanol and concentrated sulfuric acid. If testing such solutions, the immersion time should be minimized and the electrode should be carefully cleaned after use.
6. Every pH electrode will eventually age and fail. The typical service life of Apera pH electrodes is 12-24 months depending on the frequency of usage and how well you keep it clean and properly stored. We recommend replacing your electrode every 12-18 months to ensure the best accuracy.

Warranty

• We warrant this electrode to be free from defects in material and workmanship and agree to repair or replace free of charge, at option of APERA INSTRUMENTS (Europe) GmbH, any malfunctioned or damaged product attributable to responsibility of APERA INSTRUMENTS (Europe) GmbH for a period of six months from delivery. Warranty period is the time limit to provide free service for the products purchased by customers, not the service life of the tester or electrodes.
• This limited warranty does not cover any damages due to:
• Transportation; storage; improper use; failure to follow the product instructions or to perform any preventive maintenance; modifications; combination or use with any products, materials, processes, systems, or other matter not provided or authorized in writing by us; unauthorized repair; normal wear and tear; or external causes such as accidents, abuse, or other actions or events beyond our reasonable control.

APERA INSTRUMENTS (Europe) GmbH

Address : Wilhelm-Muthmann-Str. 18 42329 Wuppertal, Germany
Tel.: +49 202 51988998
Website: aperainst.de
Email: info@aperainst.de

References

• Apera Instruments

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>