legrand WNRCB40 Wireless Smart Scene Controller Installation Guide

**WNRCB40 radiant ® Wireless Smart Scene Controller with Netatmo
No. 341363 5/22
Installation Instructions
Country of Origin: Made in China

WNRCB40  radiant® Wireless Smart Scene Controller with Netatmo**

BEFORE YOU START

Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.
WARNING: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
CAUTION: To reduce the risk of injury and/or overheating and damage to other equipment:

• For dry, indoor use only.
• Do not use to power medical equipment – not suitable as a disconnecting means.

YOU MAY NEED

• Phillips-head screwdriver
• Flat blade screwdriver
  You May Also Need:
  Voltage tester, pliers, wire cutter, wire stripper, electrical tape, and wire nut.

INSTALLATION

1. Choose a place to install the device
   This device can be installed on a flat wall surface or in any standard U.S.
   electrical wall box. It may also be installed over the wall next to a standard U.S. electrical wall box, if used with a multi-gang Legrand radiant wall plate, catalog number beginning with RWP26-XXX.
   INSTALLATION (on a wall surface)

2.  Use provided double sided stickers to install on a tiled or other smooth surface. Markings on the back of the device indicate location for the stickers.

3. Use provided mounting screws to install on dry wall or uneven surface where the sticker may not work.
   Do not remove label or pull out ground wire as device may not sit flush.

INSTALLATION (in an electrical box) (See Figure A)

1. Turn off power to the box at circuit breaker.Note: Ensure power is off to all devices in the electrical box. Remove old device from box. Install wire nuts to terminate all the exposed wires that were previously connected to the old device. Ensure complete electrical insulation by securing the wire nuts making sure no bare wire is exposed.
2. Install and secure the device
   a. Fold the wires into the electrical box, taking care not to pinch a wire.
   b. Remove label on back of the device to expose ground wire and connect it to the box ground.
   c. Use included mounting screws to secure the device to the electrical box.

INSTALLATION (NEXT TO AN ELECTRICAL BOX)

1. Break off the tabs on device
   Break off the tabs at the top and bottom of the device using pliers as shown in image (Figure B).
   Mark the location of the device on the wall surface to the left or right of existing device(s) installed in the electrical box by visually aligning it with existing device(s).

2. Install and secure the device
   a. Fold the wires into the electrical box, taking care not to pinch a wire.
   b. Use double sided stickers to install on tiled or any other smooth surface next to the electrical box.
   c. Use provided mounting screws if the surface next the electrical box is dry wall or uneven surface where the sticker may not work.
   d. Install the multi-gang subframe using sub-frame screws provided with the radiant wall plate.
   e. Snap-on the radiant wall plate.
   If installing with a non-radiant wall plate, skip steps “e” and “f” above and use screws provided with the other wall plate to secure this device.

SETUP

Remove battery insulation tab as shown in the image (see Figure B).Set Up Your System (connect to your network)

3. Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.

4. Connect your smart device to your home network by following the step by step instructions in the app.

5. Use the app to control your smart device.
   Set Up Your System (if network access is not yet available) https://www.legrand.us/p/wnrcb40wh

6. Press the Gateway EZ button for 5 seconds and let go. The LED will turn solid green.

7. Briefly press one of the buttons on the Scene Controller to activate it.
   The LED on the screen controller will flash green, then turn off.
   6. To complete the installation, briefly press the Gateway EZ button. All LEDs on the products will switch off.

8. Once Network is available: Download and Open the Legrand Home + Control app. Customize your scenes in the Settings/Scenes section.
   For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: https://www.legrand.us/p/wnrcb40wh

GETTING TO KNOW YOUR BATTERY POWERED DEVICE

LED Indicator Light Explanations

Reset To Factory Default (Figure D):
To manually reset the device to factory defaults, press and hold the EZ Button for 10 seconds until you see the LED blink red, then release. The LED will turn off when the reset is complete.

Replace Battery (Figure D):
Replace battery upon receiving low battery alert in Home + Control app.
Average battery life is 8 years. To replace, remove switch cover and slide battery out. Replace with CR2032 3V battery.
Legrand reserves the right to change specifications without notice.

REGULATORY INFORMATION

FCC NOTICE: This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
  This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 90 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.
  NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and theuser’s authority to operate the equipment. Contains FCC ID: 2AU5D-WRCB4
  IC NOTICE: This device complies with Industry Canada licenseexempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference  that may cause undesired operation of the device.
  RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the
  minimum separation distance of 90 mm to the human body. Note: Any changes or modifi cations to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.
  IC: 25764-WRCB4 HVIN: WNRCB4

LIMITED ONE YEAR WARRANTY

Legrand will remedy any defect in workmanship or material in Legrand products which may develop under proper and normal use within one years from date of purchase by a consumer:
(1) by repair or replacement, or, at Legrand’s option, (2) by return of an amount equal to consumer’s purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Legrand does not include or cover cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or limitation of incidental or consequential damages, so the above disclaimer and limitation or exclusion may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED  WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE one YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)
To ensure safety, all repairs to Legrand products must be made by Legrand, or under its specific direction. Procedure to obtain performance of any warranty obligation is as follows: (1) Contact Legrand, Syracuse, New York 13221, for instructions concerning return or repair; (2) return the product to Legrand, postage paid, with your name and address and a written description of the installation or use of the Legrand product, and the observed defects or failure to operate, or other claimed basis for dissatisfaction. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

For covering patents, see www.legrand.us/patents
No: 341363 5/22
© Copyright 2022 Legrand All Rights Reserved.
Questions? We’re here to help.
Phone: 1-877-833-3303 8:00 a.m. to 8:00 p.m. EST (M-F)
Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart- lighting.aspx
(Click on the chat icon to open a dialogue box)
Correo electrónico: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart-lighting.aspx
Vous avez des questions? Nous sommes là pour vous aider.
Courriel : smartlighting@legrand.us
Clavardage : https://www.legrand.us/radiant/smart-lighting.aspx

800.223.4185
1.877.BY.LEGRAND
www.legrand.us
www.legrand.ca

References

• Patents | Legrand
• radiant Wireless Smart Scene Controller with Netatmo
• Smart Lighting from the radiant Collection ⎸Legrand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>