SEALEY HVD30.V3 Industrial High Velocity Drum Fan Instruction Manual
- June 12, 2024
- SEALEY
Table of Contents
SEALEY HVD30.V3 Industrial High Velocity Drum Fan
Product Information
Product Name: 30 Industrial High Velocity Drum Fan 230V
Model Number: HVD30.V3
Manufacturer: Sealey
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
SAFETY
ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe
before using. Inspect power supply leads, plugs and all electrical connections
for wear and damage. Sealey recommend that an RCD (Residual Current Device) is
used with all electrical products. You may obtain an RCD by contacting your
local Sealey stockist.If the product is used in the course of business duties,
it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested. Electrical safety information, it is important that
the following information is read and understood. Ensure that the insulation
on all cables and on the appliance is safe before connecting it to the power
supply. Regularly inspect power supply cables and plugs for wear or damage and
check all connections to ensure that they are secure.
Important: Ensure that the voltage rating on the appliance suits the
power supply to be used and that the plug is fitted with the correct fuse –
see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
DO NOT pull the plug from the socket by the cable.
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any
faulty item is repaired or is replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 3 pin plug. If the cable or plug is
damaged during use, switch off the elec tricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician. Replace a
damaged plug with a BS1363/A 3 pin plug. If in doubt contact a qualified
electrician.
- Connect the GREEN/YELLOW earth wire to the earth terminal ‘ E’.
- Connect the BROWN live wire to the live terminal ‘L’.
- Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight. Sealey recommend that repairs are carried out by a qualified el ectrician.
GENERAL SAFETY
-
Disconnect the fan from the mains power when not in use and before servicing or performing any
maintenance. -
Use the fan in dry areas only. DO NOT use in wet or areas with high condensation such as showers, pools etc.
‰ WARNING! If a fan falls into water or other liquid, immediately switch off and disconnect from the mains power supply. DO NOT touch
the fan until the mains power supply has been disconnected. -
Always disconnect the fan from the power supply when moving it from one location to another and ensure fan is stood on a level
surface. -
The fan air flow is powerful. Before use ensure that there is nothing nearby that will be damaged or displaced by the stream of air.
-
Keep the fan clean and maintained in good condition. For motor service contact an authorised service agent.
-
Use recommended parts only. Unapproved parts may be dangerous, and will invalidate your warranty.
-
DO NOT operate the fan where there are explosive or flammable gases, fumes or other hazardous substances.
-
DO NOT stand the fan on the power cable.
-
DO NOT insert any objects through the fan guard.
-
DO NOT cover the fan when in use.
-
DO NOT immerse the fan in water or any other liquid.
-
DO NOT allow children to operate the fan.
-
DO NOT stand the fan where it may be knocked over or off a surface, or where the lead may cause a person to trip.
-
DO NOT modify speed control or attempt to fit any additional external speed control device to the fan.
-
When not in use place the fan in its original box, or cover , to protect from dust and store in a safe, dry , childproof location.
NOTE: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
INTRODUCTION
High velocity industrial 2-speed drum fan suitable for movement of huge volumes of air. Robust unit with heavy-duty gauge steel casing, guard and frame. Handle, wheels and tilt function cradle stand allow control of airflow where it is needed. Carefully balanced and fully guarded blades provide safe operation. Fitted with 3-pin plug. Suitable for use in industrial, commercial, agricultural, automotive workshop and showroom applications.
SPECIFICATION
Model No:…………………………………………………….HVD30.V3
Current:……………………………………………………………….0.52 A
Fan diameter:…………………………………………..Ø760 mm (30”)
Speed range:………………………………………………800-900 rpm
Speeds:………………………………………………………………………2
Supply:…………………………………………………………………230 V
Maximum fan flow rate (F):………….283.4 m3/min (10008cfm)
Fan power input (P):…………………………………………..118.6 W
Service value (SV):……………………………………2.4 (m3/min)/W
Standby power consumption (PSB):………………………………0W
Seasonal electricity consumption (Q):……………… 38.0 kWh/a
Fan sound power level (LWA):……………………………….78 dB(A)
Maximum air velocity (c):……………………………………..2.2 m/s
OPERATION
WARNING! Ensure that you read, understand and apply safety instructions in Section 1 before using fan.
- Check that the speed control is set to “0” (of f) and then plug into the mains power supply and switch the power on.
- The fans feature 2 speeds which are selectable using the switch located at the back of the fan, above the motor.
- Adjust the direction of the air flow by moving from side to side and tilting the fan up or down as required.
- When you have finished using the fan ensure you turn the speed control switch to “0” (of f) and disconnect the fan from the mains power.
MAINTENANCE
WARNING! Ensure that the fan is disconnected from the mains power supply before attempting any of the following:
- Use a soft, damp cloth to clean the fan.
- DO NOT immerse the fan in water and never allow water to drip onto the motor housing. DO NOT use solvents, petroleum, paint thinner or other chemicals to clean the fan.
- To clean the fan blade, undo the cross headed screws around the circumference, remove the grille and clean the blade with a slightly damp cloth. Replace the grille as required and refit the cross headed screws.
- Should the motor, switch or the power lead require service or maintenance contact your local service agent.
- When not in use place the fan in its original box or otherwise cover to protect from dust, and store in a safe, dry, childproof location.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with
the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice. Please note that other versions of this product are available.
If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>