Momentum Recon E HL 50 STVZO Front Headlight User Manual

Momentum Recon E HL 50 STVZO Front Headlight

WARNING

• Do not look directly into the light beam or shine it directly into the eyes ofother people.
• Do not touch the light case or LED when the light is on as they can become very hot.
• Keep light out of reach of children.
• RECON E HL LED lights have a water resistance rating of IPX6 under regulardaily use and are not designed to be submerged in water. Submerging RECON E HL LED lights under water will damage the light and void the warranty.
• Do not attempt to disassemble or repair the light; doing so will void the warranty.
• Be sure to direct the light beam downward to avoid blinding oncoming pedestrians or drivers.
• Do not use high mode on public roads.
• Before your ride, please make sure the light is firmly mounted to the bracket, that it functions correctly and is not blocked by baggage, etc.
• In case unexpected light shutoff or battery issues, carrying a spare light is recommended.
• If the light, light case or accessories become dirty with mud or dust, clean them with a soft cloth moistened with mild soap. Never use alcohol, benzene or solvents, doing so will result in damage and void the warranty.
• Giant Bicycles Inc. does not accept any liability for injuries or other damages resulting from the improper use or improper installation of this product under any circumstance.

INTRO

• To ensure proper use and care of your new RECON E HL LED lights, PLEASE READ ENTIRE MANUAL BEFORE INSTALLATON AND OPERATION.
• Traffic laws mandating bicycle lights vary from country to country. Please make sure you are following the appropriate bicycle light laws and regulations in your country of use.
• RECON E L LED lights can be controlled via the on board electronics of your E-bike system and are only to be mounted on E-bikes with DC voltage that have their own battery charge indication and control. The E-bike system must also be capable of automatically shutting the light off when the on board battery reaches critical voltage to avoid deep battery discharge.
• RECON E HL LED lights are powered by the motor of your E-bike and need to be manually installed. Depending on make and model/battery type, correct installation may require some disassembly of the bike and motor and additional wiring to connect the light to the motor. Please follow the appropriate Giant How-To video for correct installation on your model / battery type or contact the e-bike or motor manufacturer for installation instructions.
• NOTE
  Incorrect disassembly, installation or assembly may void the warranty of your e-bike and or light. It is highly recommended that a trained E-bike technician install your lights.

ALIGNING THE RECON E HL BEAM

1. Place the bike 2.5 m away from a wall and face your bike to the wall.
2. Turn on the RECON E HL and put it in high-beam mode
3. Make sure it is parallel to the ground
4. Mark the cut-off line of the beam on the wall, where the beam ends above and is brighter below
5. Measure and mark 7 cm below the cut off line above
6. Adjust the RECON E HL so that the height of the beam matches the new, lower cut off line

NOTE
Make sure to follow the steps above to achieve a glare-free beam that is compliant with German road law.

INSTALLATION

Before your ride, please make sure the light is firmly mounted to the bracket at a height of 70 cm to 120 cm, that it functions correctly and is not blocked by baggage, etc.

CONNECTION

Link To Video Tutorials: www.giant- bicycles.com/global/recon-e-lights

TECHNICAL DATA

MOTOR COMPATIBILITY

• Bosch (6V) / Bosch (12V)
• Shimano E5000, E7000, E6100, E6110, E9000
• Shimano E6000, E6001, E6010, E6050
• Shimano E8000, E8080, E6002, E6012
• Yamaha PWse / Yamaha PW
• Brose Drive S (2018)

WARRANTY

• In U.S.A, and U.K., RECON E HL LED Lights carry a two (2) year warranty to the original owner from the original purchase date (proof of purchase required).
• RECON E HL warranties cover all manufacturing defects in materials or workmanship.
• For all warranty issues worldwide, please contact an authorized Giant retailer and present proof or purchase.
• If an LED not working correctly or not working at all, do not use your light anymore. The light will need to be replaced immediately.
• Normal wear and tear or damage arising from improper installation, attempting to access or modify electronics, accidents, misuse, abuse and/or neglect are not covered by the warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>