Giant Recon E HL 150 STVZO Front Headlight User Manual
- June 12, 2024
- GIANT
Table of Contents
Giant Recon E HL 150 STVZO Front Headlight
WARNING
- Do not look directly into the light beam or shine it directly into the eyes of other people.
- Do not touch the light case or LED when the light is on as they can become very hot.
- Keep light out of reach of children.
- RECON E HL LED lights have a water resistance rating of IPX6 under regular daily use and are not designed to be submerged in water. Submerging RECON E HL LED lights under water will damage the light and void the warranty.
- Do not attempt to disassemble or repair the light; doing so will void the warranty.
- Be sure to direct the light beam downward to avoid blinding oncoming pedestrians or drivers. Before your ride, please make sure the light is firmly mounted to the bracket, that it functions correctly and is not blocked by baggage, etc.
- If the light, light case or accessories become dirty with mud or dust, clean them with a soft cloth moistened with mild soap. Never use alcohol, benzene or solvents, doing so will result in damage and void the warranty.
- Giant Bicycles Inc. does not accept any liability for injuries or other damages resulting from the improper use or improper installation of this product under any circumstance.
INTRO
- To ensure proper use and care of your new RECON E HL LED lights, PLEASE READ ENTIRE MANUAL BEFORE INSTALLATON AND OPERATION.
- Traffic laws mandating bicycle lights vary from country to country. Please make sure you are following the a propriate bicycle light laws and regulations in your country of use.
- RECON E HL LED lights can be controlled via the on board electronics ofyour E-bike system and are only to be mounted on E-bikes with DC voltage that have their own battery charge indication and control. The E-bike system must also be capable of automatically shutting the light off when the on board battery reaches critical voltage to avoid deep battery discharge.
- RECON E HL LED lights are powered by the motor of your E-bike and need to be manually installed. Depending on make and model/battery type, correct installation may require some disassembly of the bike and motor and additional wiring to connect the light to the motor. Please follow the appropriate Giant How-To video for correct installation on your model / battery type or contact the e-bike or motor manufacturer for installation instructions.
- NOTE
Incorrect disassembly, installation, or assembly may void the warranty of your e-bike and / or light. It is highly recommended that a trained E-bike technician install your lights.
ALIGNING THE RECON E HL BEAM
- Place the bike 2.5 m away from a wall and face your bike to the wall.
- Turn on the RECON E HL and put it in high-beam mode
- Mark the cut-off line of the beam on the wall, where the beam ends above and is brighter below
- Measure and mark 7 cm below the cut off line above
- Adjust the RECON E HL so that the height of the beam matches the new, lower cut offline
NOTE
Make sure to follow the steps above to achieve a glare-free beam that is
compliant with German road law.
RECON E HL LED lights can be controlled via the on board electronics of your
E-bike system and are only to be mounted on E-bikes with DC voltage that have
their own battery charge indication and control.
The E-bike system must also becapable of automatically shutting the light off when the on board battery reaches critical voltage to avoid deep battery discharge.
INSTALLATION
Before your ride, please make sure the light is firmly mounted to the bracket
at a height of 70 cm to 120 cm, that it functions correctly and is not blocked
by baggage, etc.
RECON E HL SIDE MOUNT (400000209)
- Fits 31.8 or 35 mm round handlebars
- Works with all Recon E Lights.
- The clamp of one side holder can be opened for easy installation
- Can be installed on either left or right side of stem
RECON E HL FORK MOUNT (400000208)
RECON E HL HB MOUNT (400000210)
OPERATION
The Remote Switch toggles between Auto Mode and Manual Mode(high beam /low beam).
- NOTE
Only RECON E HL 1000 and RECON E HL 150 StVZO work with remote controls for switching lighting modes.
CONNECTION
Link To Video Tutorials: www.giant- bicycles.com/global/recon-e-lights
OPTIONAL CABLES FOR NON-YAMAHA MOTORS:
NOTE
Giant / Yamaha motor cable included. Cables for non-Yamaha motors are not
included and must be purchased separately. Contact your authorized Giant
retailer for more information.
TECHNICAL DATA
MOTOR COMPATIBILITY
- Bosch (6V) / Bosch (12V)
- Shimano E5000, E7000, E6100, E6110, 9000
- Shimano E6000, E6001, E6010, E6050
- Shimano E8000, E8080, E6002, E6012
- Yamaha PWse / Yamaha PW
- Brose Drive S (2018)
WARRANTY
- In U.S.A. and U.K., RECON E HI LED Lights carry a two (2) year warranty to the original owner from the original purchase date (proof of purchase required).
- RECON E HL warranties cover all manufacturing defects in materials or workmanship.
- For all warranty issues worldwide, please contact an authorized Giant retailer and present proof or purchase.
- If an LED is not working correctly or not working at all, do not use your light anymore. The light will need to be replaced immediately.
- Normal wear and tear or damage arising from improper installation, attempting to access or modify electronics, accidents, misuse, abuse and/or neglect are not covered by the warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>