Pablo 050923 Totem Pendant Instruction Manual

Pablo 050923 Totem Pendant

Product Information

The Totem Pendant is a high-quality LED lamp designed by Pablodesigns. It features a unique design with hand-blown opal glass shades. The lamp has both uplight and downlight modules, providing a versatile lighting solution for any space. The lamp has a high output LED array with a power rating of 20 watts. It emits 1800 lumens of light in the downlight mode and 600 lumens in the uplight mode. The color temperature can be adjusted between 2700K and 2200K DTW (Dim to Warm). The lamp is suitable for professional installation and comes with a canopy bracket driver attached, canopy cover, dust cap, and all necessary components for assembly.

Product Usage Instructions

1. Mount the ceiling bracket using the provided hardware.
2. Attach the uplight module to the upper shade using the threaded coupler.
3. Fasten the lower shade to the upper shade using the coupler. Place the rubber gasket between the coupler and glass surface. Remove the film liner from the rubber gasket.
4. Screw the downlight module onto the shade assembly.
5. Feed the cords through the dust cap and canopy cover.
6. Remove one cable gripper from the housing for use with the power cable. Feed the power cable through the cable gripper and housing. Reattach the cable gripper to the housing.
7. Feed the remaining two suspension wires through the cable grippers and pull all three cables until the lamp reaches the desired hang height. Use a leveling tool as necessary and continue to adjust the cables until the full lamp assembly appears level.

Please note that the lamp should be installed by a professional electrician. Care instructions include wiping the shades with a soft cloth. Additionally, it is recommended to open the shade packaging within 10 days of delivery to report any damage caused during shipping.

TOTEM UP/DOWN

CONTENTS

• A. CANOPY BRACKET °DRIVER ATTACHED˝
• B. CANOPY COVER
• C. DUST CAP
• D. UPLIGHT MODULE SUBASSEMBLY
• E. UPPER SHADE
• F. SHADE COUPLER
• G. LOWER SHADE
• H. RUBBER GASKET
• I. SHADE COUPLER
• J. DOWNLIGHT MODULE
  NOTE: WE HIGHLY RECOMMEND THIS LAMP BE INSTALLED BY A PROFESSIONAL ELECTRICIAN!!!

SPECIFICATIONS

• HIGH OUTPUT LED ARRAY
• HAND˜BLOWN OPAL GLASS SHADES 20 WATT
• 2700˜2200DTW
• 1800 LUMENS °1200DOWN˛600UP˝

CARE INSTRUCTIONS

WIPE SHADES WITH SOFT CLOTH
NOTE: SHADE PACKAGING MUST BE OPENED WITHIN 10 DAYS OF DELIVERY TO REPORT DAMAGE CAUSED DURING SHIPPING.

ASSEMBLY

1. MOUNT CEILING BRACKET.
2. FASTEN UPLIGHT MODULE TO UPPER SHADE USING THREADED COUPLER.

3. FASTEN LOWER SHADE TO UPPER SHADE USING COUPLER. PLACE RUBBER WASHER BETWEEN COUPLER AND GLASS SURFACE. NOTE! REMOVE FILM LINER FROM RUBBER WASHER.

4. THREAD DOWNLIGHT MODULE ONTO SHADE ASSEMBLY.
5.  FEED CORDS DUST CAP AND CANOPY COVER.

6. A. REMOVE 1 CABLE GRIPPER FROM HOUSING ˜FOR USE WITH POWER CABLE°.
   B. FEED POWER CABLE THROUGH CABLE GRIPPER AND HOUSING.
   C. RE ATTACH CABLE GRIPPER TO HOUSING.

7. FEED REMAINING 2 SUSPENSION WIRES THROUGH CABLE GRIPPERS AND PULL ALL 3 CABLES UNTIL LAMP REACHES DESIRED HANG HEIGHT. USE LEVELING TOOL AS NECESSARY AND CONTINUE TO ADJUST CABLES UNTIL FULL LAMP ASSEMBLY APPEARS LEVEL.

8. ONCE LAMP HEIGH IS SET, TRIM EXCESS CABLE.
   ˜NOTE! AUXILIARY STRAIN RELIEFS CAN BE ADDED TO CABLES AT THIS POINT FOR ADDED SUPPORT°.

   • A. UNSHEATHE COAXIAL POWER CABLE AND SEPARATE INNER AND OUTER CONDUCTORS. NOTE: INNER CONDUCTOR CARRYS POSITIVE CHARGE.
   • B. WIRE DRIVER TO BUILDING ˛US: BLACK TO BLACK ˛°˝˙WHITE TO WHITE ˛+˝˝ ˛EU: BLACK TO BLUE ˛°˝˙WHITE TO BROWN ˛+˝˝. WIRE DRIVER TO LAMP ˛ i. – RED TO INNER˛+˝˙ ii – BLUE TO OUTER ˛°˝˝. ˛SECURE BUILDING GROUND WIRE TO GREEN SCREW˝

9. SECURE CANOPY COVER TO MOUNT BRACKET BY MAGNETIC CONNECTION.
10. GENTLY PRESS DOWN ONTO DUST CAP TO MOVE DOWN INTO PLACE. WE RECOMMEND UPPER SURFACE BE SET FLUSH TO OR JUST BELOW SHADE EDGE.

TOTEM DOWNLIGHT

CONTENTS

• A. CANOPY BRACKET °INCLUDES DRIVER˝
• B. CANOPY COVER
• C. LAMP COVER
• D. DOWNLIGHT MODULE SUBASSEMBLY
• E. SHADE
• F. SHADE COUPLER
• G. LIGHT MODULE
  NOTE: WE HIGHLY RECOMMEND THIS LAMP BE INSTALLED BY A PROFESSIONAL ELECTRICIAN!!!

SPECIFICATIONS

• HIGH OUTPUT LED ARRAY
• HAND˜BLOWN OPAL GLASS SHADES 20 WATT
• 2700˜2200DTW
• 1400 LUMENS

CARE INSTRUCTIONS

WIPE SHADES WITH SOFT CLOTH
NOTE: SHADE PACKAGING MUST BE OPENED WITHIN 10 DAYS OF DELIVERY TO REPORT DAMAGE CAUSED DURING SHIPPING.

ASSEMBLY

1.  MOUNT CEILING BRACKET ASSEMBLY TO JBOX OR CEILING USING APPROPRIATE FASTENERS. USING INCLUDED VHB TAPE, MOUNT DRIVER TO THE CANOPY BRACKET.
   REMOVE CABLES FROM PACKAGING AND EXTEND THE ENTIRE ASSEMBLY. SHADE ASSEMBLY SHOULD BE COMPLETED ON TABLE TOP OR STURDY SURFACE BELOW.

2. FASTEN LIGHT MODULE TO SHADE WITH COUPLER. NOTE! COUPLER COMES WITH RUBBER WASHER ATTACHED. ORIENT COUPLER SO THAT THE RUBBER WASHER CONTACTS THE GLASS DIRECTLY.

3. THREAD LIGHT MODULE ONTO SHADE ASSEMBLY.
4. PULL ALL 3 CABLES UNTIL LAMP REACHES DESIRED HANG HEIGHT. USE LEVELING TOOL AS NECESSARY AND CONTINUE TO ADJUST CABLES UNTIL FULL LAMP ASSEMBLY APPEARS LEVEL.

5.  ONCE LAMP HEIGH IS SET, MOVE AUXILIARY STRAIN RELIEFS FURTHER DOWN CABLE ADJACENT TO CABLE GRIPPER ˜TYPE A FOR NON POWER CABLES˝TYPE B FOR POWERED CABLE°. TRIM EXCESS CABLE.
6.  A. UNSHEATHE COAXIAL POWER CABLE AND SEPARATE INNER AND OUTER CONDUCTORS. NOTE: INNER CONDUCTOR CARRYS POSITIVE CHARGE.
   B. WIRE DRIVER TO BUILDING ˛US: BLACK TO BLACK ˛°˝˙WHITE TO WHITE ˛+˝˝ ˛EU: BLACK TO BLUE ˛°˝˙WHITE TO BROWN ˛+˝˝. WIRE DRIVER TO LAMP ˛ i. – RED TO INNER˛+˝˙ ii – BLUE TO OUTER ˛°˝˝.

7. SECURE CANOPY COVER TO MOUNT BRACKET BY MAGNETIC CONNECTION.

FLUSH MOUNT

CONTENTS

• A. CANOPY BRACKET °DRIVER ATTACHED˝
• B. CANOPY COVER
• C. RUBBER WASHER
• D. SHADE
• E. RUBBER WASHER
• F. SHADE COUPLER
• G. LIGHT MODULE
  NOTE: WE HIGHLY RECOMMEND THIS LAMP BE INSTALLED BY A PROFESSIONAL ELECTRICIAN!!!

SPECIFICATIONS

• HIGH OUTPUT LED ARRAY
• HAND˜BLOWN OPAL GLASS SHADES 20 WATT
• 2700˜2200DTW
• 1400 LUMENS

CARE INSTRUCTIONS

WIPE SHADES WITH SOFT CLOTH
NOTE: SHADE PACKAGING MUST BE OPENED WITHIN 10 DAYS OF DELIVERY TO REPORT DAMAGE CAUSED DURING SHIPPING.

ASSEMBLY

1. MOUNT CEILING BRACKET USING INCLUDED HARDWARE. SECURE DRIVER TO BRACKET WITH PROVIDED VHB TAPE.

2. A.WIRE DRIVER TO DC JACK ˛RED TO RED˛+˝˙BLACK TO BLUE˛°˝˝
   B.WIRE DRIVER TO BUILDING ˛US: WHITE TO WHITE˛+˝˙BLACK TO BLACK˛°˝˝ ˛EU: WHITE TO BROWN˛+˝˙BLACK TO BLUE˛°˝˝ ˛SECURE BUILDING GROUND WIRE TO GREEN SCREW˝

3. SECURE CANOPY COVER TO CEILING BRACKET VIA MAGNETIC CONNECTION.

4.  A. REMOVE 1 CABLE GRIPPER FROM HOUSING.
   B. FEED POWER CABLE THROUGH CABLE GRIPPER AND HOUSING.
   C. RE ATTACH CABLE GRIPPER TO HOUSING.

5.  FEED REMAINING 2 SUSPENSION WIRES THROUGH CABLE GRIPPERS AND PULL ALL 3 CABLES UNTIL LAMP REACHES DESIRED HANG HEIGHT. USE LEVELING TOOL AS NECESSARY AND CONTINUE TO ADJUST CABLES UNTIL FULL LAMP ASSEMBLY APPEARS LEVEL.

FOR MORE INFO

ABOUT COMPANY

• INFO@PABLODESIGNS.COM
• INFO@PABLODESIGNS.EU
• 888 MARIN ST
• SAN FRANCISCO, CA
• 94124
• PABLODESIGNS.COM
• PABLODESIGNS.EU

References

• Pablo
• Pablo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>