LIORQUE Weather Station User Manual

LIORQUE Weather Station

Main Unit

1. Weather Forecast (Next 12-24Hrs)

2. 12/24Hrs Time

3. Dual Alarm Clock

4. Date

5. 7-language Day of the Week

6. Pressure

7. Indoor Temperature & Humidity

8. Outdoor Temperature & Humidity

9. Channel

10. Indoor Temperature & Humidity Max/Min Record

11. Outdoor Temperature & Humidity Max/Min Record

12. Low Battery Indication of the Main Machine

13. Low Battery Indication of the Outdoor Sensor

14. Snooze/Backlight

15. Time & Date Setting

16. Increase Time OR Indoor/Outdoor Temperature & Humidity
    Max/Min Value Display

17. Decrease Time OR Indoor/Outdoor Temperature °C/°F Unit Switch

18. Pressure & Weather Setting

19. Outdoor Sensor Channel Selection

20. Alarm clock Setting

21. Hanging Hole

22. Battery Cover

23. Stand
    

Outdoor Sensor

1. signal Indicator
2. Hanging Hole
3. Battery Cover
4. Channel Selection
5. Test Button
   

Installation

Install the batteries into the main unit and outdoor sensor, the main unit screen will light up and the outdoor unit will flash red signal light, which means normal start up.

Channel Pairing

After installing batteries in the main unit and outdoor unit, switch channel 1-2-3 of the outdoor unit to whatever channel you want.
Main unit reception sequence is CH1-CH2-CH3, and the maximum reception time is 3 minutes. will keep flashing, if no signa l is found within 3 minutes, it will quit searching.
If the main unit does not receive any signals, you can re-receive it by pressing and holding CHANNEL button.
Attention:
Before pairing, please switch the main unit and the outdoor unit to the same channel. e.g. if the outdoor unit channel is CH1, then the main unit channel should also be switched to CH1.

Main Unit Setting

After power up, the screen will be fully displayed for 3 seconds with the BI sound and the backlight will keep on for 10 seconds.
The weather icon will flash and you can press+/- button to adjust the current weather conditions or wait 25 seconds/short press the PRESSURE button to exit, the weather forecast will be updated automatically within 12-24 hours.

Default Display

Time| Time format| Time zones| Language of week| Temperature units| Pressure units| Date format
---|---|---|---|---|---|---
AM 12:00| 12H| 00H| EN| ºC| hPa / mb| M/D

12/24H Switch

Short press SET button to switch between 12/ 24 hour display, 12 hour when AM/PM is displayed, 24 hour when there is no display.

Time & Date Setting

Press and hold the SET button to enter the hour setting, press+/- to adjust the hour digit (long press +/- for quick adjustment), Short press the SET button again to enter the minute setting, press+/- to adjust the minute digit (long press+/- for quick
adjustment), Short press the SET button again to enter the year setting, press+/- to adjust the year digit (long press+/- for quick adjustment).
Year range: 2000-2099
Short press the SET button to enter the date and month setting, the adjustment order is Month-Date, short press +/-to adjust the month/date digits (long press+/- for quick adjustment),
Short press the Set button again to enter the date and month format setting, you can adjust the month and date format to
Month/Date or Date/Month,
Short press the Set button again to enter the multi-language day of the week setting, you can set the day of the week in 7 languages: English – German – French – Italian – Spanish – Danish – Swedish.

The display is as following:

When the setting the language for the week finished, short press the SET button to exit and the day of the week will be updated automatically.

Max/Min Record

Short press the + button to display the maximum – minimum – current values of indoor/outdoor temperature and humidity for the last 24 hours.
In the MAX/MIN display, press and hold this button to clear the maximum and minimum indoor and outdoor temperature and humidity values.

°C/°F Switch
Press and hold the – button to switch the indoor and outdoor temperature °C/°F units.

Pressure Setting

Short press the PRESSURE button to switch the display of Absolute/Relative air pressure.
Abs= absolute air pressure; Rel= relative air pressure

1. In the Abs display, press and hold the PRESSURE button, then the pressure unit will flash, press+/- to adjust the unit display in mb hPa/inHg.
2. In the Rel display, press and hold the PRESSURE button, then the pressure unit will flash,, press+/- to adjust the unit display in mb hPa/inHg.
   After the setting the units finished, short press the PRESSURE button again to adjust the specific pressure value, then press and hold the PREESURE button to enter the weather forecast setting, press+/- to set the weather forecast.

Weather forecast icon

Sunny| Sunny to cloudy| cloudy| Light rain| Heavy rain| Snowy
| | | | |

Attention:
The “Snowy” weather forecast cannot be set manually. It is only displayed when the temperature is below 0°C and the humidity is high.

Outdoor Sensor Reception Setting

Short press the CHANNEL button to adjust the outdoor sensor channel, the display order is CH7-CH2-CH3- (cyclical display). When in the cyclic display, the screen will show It will automatically display the outdoor temperature and humidity with received data, switching the display every 10 seconds, channels with no data will not be displayed. Eg: when you have 2 outdoor sensors, CH1 and CH3 have data reception, CH2 has no data reception, the cyclic display will only show the data of CH1 and CH3 in turn.
If no data is received, or if you want to search again, you can press and hold the CHANNEL button , will flash and stop flashing when data is received.

Alarm Clock Setting

In the normal display, short press the ALARM button, it will display alarm 1 – alarm 2 – current time.
When the alarm 1 time is displayed, short press the SET button to turn the alarm ON/OFF, when appears, alarm 1 is ON. When the alarm 1 time is displayed, press and hold the ALARM button to set the hour-minute-volume of the alarm. Adjust the number with+/- button (long press for quick adjustment), then short press the ALARM button again to confirm and go to the next setting.L01 = High volume, L02 = Low volume. Short press the ALARM button to exit when the volume setting is finished .
Alarm 2 setting is as the same as alarm 1.

Snooze Function

When the alarm goes off, the backlight lights up for 10 seconds, or flashes, press any button to stop the alarm.
If you want to turn on the snooze function, when the alarm goes off, short press Zzz· , to enter snooze, the Zzz· on the screen will flash and the maximum of snooze is 3 times, each interval is 7 minutes.
During snooze, press any button to exit this function.

Indoor/Outdoor Temperature, Humidity, Pressure and Trend Function

Indoor temperature range: -9.9 °c ~ 50 °c, lower than -9.9 °c will display LL.L; higher than 50 °c will display HH.H.
Outdoor temperature range: -40 °C ~ 60 °C, lower than -40 °C will display LL.L; higher than 60 °C will display HH.H.
+/-1 degree error between o to 40 degrees
+/-2 degrees error between Oto -40 degrees and 40 to 60 degrees.
Indoor and outdoor humidity range: 10% ~ 99%, lower than 10% will display LL; higher than 99% will display HH.
When the temperature is rising continuously by more than 1 °C & 1.8°F, the temperature trend icon shows” .
When the temperature is falling continuously by more than 1°C & 1.8°F, the temperature trend icon shows”-
When the cumulative value of temperature rise or fall does not exceed 1°c & 1.8°F within 1 hour, the temperature trend icon shows
When the humidity is rising continuously by more than 5% RH, the humidity trend icon shows ” “.
When the humidity is falling continuously by more than 5% RH, the humidity trend icon shows”- “.
When the cumulative value of the humidity rise or fall does not exceed 5% RH within 1 hour, the humidity trend icon shows” “.
When the current pressure is 1 hPa higher than the pressure of the past 1 hour, the press trend icon shows” “.
When the current pressure is 1 hPa lower than the pressure of the past 1 hour, the press trend icon shows ” –
When the current pressure does not change by more than 1 hPa from the last 1 hour, the press trend icon shows” “.
Temperature and humidity detection cycle: 30 seconds
pressure detection cycle: 20 minutes

Low Power Warning

When the main unit battery voltage is too low (3.3V), a battery icon will indicated at the indoor temperature.
When the outdoor sensor battery voltage is too low (2.6V), a battery icon will indicated at the outdoor temperature.
When the screen lights up with the low battery icon, it is recommended to replace the battery as soon as possible.

Attention

1. Please do not expose the outdoor sensor to direct rain or sunlight.

2. Please keep the sensor well ventilated and leave a certain distance between the sensor and the wall to avoid blocking the ventilation of the outdoor sensor.
   

3. Please place the outdoor sensor at a height of approximately 2.5 m / 8.20 ft vertical.

4. Please place the outdoor sensor on a flat surface or hang it steadily in a ventilated area.

5. If there is interference from other 433gHz devices in the house or excessive wall obstruction, the outdoor sensor may be disconnected frequently, please check the correct installation position before reconnecting.
   If you meet any problems when using the machine, please contact us via support@liorque.net

FCC Statement

Operation is subject to the following three conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with t he limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• consult the dealer or an experienced radio/TV technician for help.

Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

EU Importer: Lucky Transport Euro Kft
Address: 7085 Budapest, Jozsef Central Street 69. Ground
Floor, 1, Hungary
Email: Lsphche@outlook.com
UK Importer: HISOA co., LTD.
Address: 19a Chorley Old Road, Bolton,Greater Manchester,
England, BL 1 3AD
Web: www.hisoa.co.uk
FCC ID: 2AW4D•YGH6208

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>