velleman Mobile Phone Surveillance Software Installation Guide

June 12, 2024
Velleman

velleman Mobile Phone Surveillance Software

velleman-Mobile-Phone-Surveillance-Software-PRODUCT

Product Information

The product is a software application that allows remote surveillance via GPRS/3G mobile phones or PDAs. It provides the ability to access and monitor DVRs and network cameras from a mobile device. The software is compatible with various operating systems including Windows Mobile, J2ME, iPhone, Symbian, and BlackBerry.

Product Usage Instructions

  1. Before using the software, ensure that your PDA or mobile phone meets the following requirements:
    • For Windows Mobile Phone: The operating system should be Windows Mobile 5.0 Packet PC / 6.0 Professional. Windows Mobile 5.0 Smartphone / 6.0 Standard is not supported.
    • For J2ME MIDP2.0 phones: Ensure J2ME is supported.
    • For iPhone: Internet services via GPRS/3G networks should be subscribed to and available to use. The port number of the connected device (such as a DVR or network camera) should not be 80. The suggested port number is 88. Download the iPhone-compatible software from the application store by searching “eagle eyes”.
  2. Set up the network configuration for the DVR and router. Ensure that you can log into the DVR via a PC connected to another modem.
  3. Software Download:
  4. Visit the following website address from your PDA or mobile phone: http://211.75.84.102/fae/MobileAP/index.html or http://www.eagleeyescctv.com/
  5. Select the application you need to download based on the device and DVR model. Refer to the provided table for guidance.

Note: The Internet access settings via WiFi or GPRS/3G networks may vary depending on the PDA or mobile phone brand. Refer to the individual user manual or consult with your local network operator or service provider for specific instructions.
Additional Note: Internet access via WiFi or GPRS/3G networks may incur charges. Check with your local network operator or service provider for the rate details.

CHECKLIST BEFORE USING

Make sure your PDA or mobile phones conform to the following requirements :velleman-Mobile-Phone-Surveillance-Software-FIG-11

We do not guarantee the compatibility of the mobile surveillance software in every touch panel PDA brand with the operating system of Windows Mobile 5 Packet PC / 6.0 Professional.
NOTE: First of all you have to set up the network configuration for the DVR and router. Check if you can log into the DVR via a PC connected to another modem (see diagram)velleman-Mobile-Phone-Surveillance-Software-
FIG-1

INSTALLATION & SETUP

Software Download

  • STEP1: To download the software for mobile surveillance, please visit the following website address from your PDA or mobile phone: http://211.75.84.102/fae/MobileAP/index.html or http://www.eagleeyescctv.com/

  • NOTE: The Internet access setting via WiFi or GPRS / 3G networks varies depending on different PDA or mobile phone brands. For details, please refer to its individual user manual, or check with your local network operator or service provider.

  • NOTE: You might be charged for Internet access via WiFi or GPRS / 3G networks. For the Internet access rate details, please check with your local network operator or service provider.
    You will see the following five applications to download:

  • BackBerry Software

  • GPRS / 3G Software

  • EagleEyes (J2ME New version)

  • EagleEyes (For WinCE)

  • EagleEyes (For WinCE New Version)

  • STEP 2: Select the application you need and start downloading. To know which program you should download, please refer to the following table:

Device DVR model download software
Symbian mobile DVR4MQAEE, DVR8N and DVR8N2 G P R S / 3 G S

o f t w a r e
Symbian mobile| DVR4H, DVR4L3, DVR4L4, DVR4L5 and DVR16H1| EagleEyes(J2ME NewVersion)
Windows mobile| DVR4MQAEE, DVR8N and DVR8N2| EagleEyes(For WinCE)
Windows mobile| DVR4H, DVR4L3, DVR4L4, DVR4L5, DVR8L1, DVR16L1 and DVR16H1| EagleEyes(For WinCE New Version)
BlackBerry| DVR4L3, DVR4L4, DVR4L5, DVR4H, DVR8L1, DVR16L1 and DVR16H1| _BlackBerrySoftware
iPhone| DVR4L3, DVR4L4, DVR4L5, DVR4H, DVR8L1, DVR16L1 and DVR16H1| iTunes application store

  • STEP3: Follow the on-screen instructions after downloading.
  • For mobile phones, the application will save to the location you specified. For PDA, the application will save to “Programs”.

GPRS / 3G MOBILE PHONE

  • The setting interface of each mobile phone may vary depending on its individual brand. Therefore, the interface shown below only illustrates the main functions of the application and is for reference only. For the actual display, please refer to your own mobile phone.

With GPRS / 3G software installed

  • STEP1: Go to the location where you save the application, and you will see the item “Supervisor”. STEP2: Select “Supervisor” to key in the information necessary for DVR or network camera remote access.
  1. IP
    • Enter the IP address or hostname (ex.dyndns) of the device you want to connect.
  2. PORT
    • Enter the port number used by the device you want to connect. You can use the port number from 0 ~ 65536 except 80. It’s recommended to use 88.
  3. Username
    • Enter the user name used to access the DVRe you want to connect.
  4. PassWord
    • Enter the password used to access the device you want to connect.
  • STEP3: Make sure the information above is correct, and confirm the connection set to start accessing the device remotely. Make sure the information above is correct, and confirm the connection set to start accessing the device remotely.

With EagleEyes (J2ME New version) installed

  • STEP1: Go to the location where you save the application, and you will see the item “EagleEyes”.
  • STEP2: Select “Connect & View” to go to the setting page, similar as follows. Key in the information necessary for DVR or network camera remote access.
  1. Host Name
    • Give a name for this connection set.
  2. User Name
    • Enter the user name used to access the DVR you want to connect.
  3. Password
    • Enter the password used to access the DVR you want to connect.
  4. IP
    • Enter the IP address or hostname (ex. dyndns) of the device you want to connect. 5. Port
    • Enter the port number used by the device you want to connect.
    • You can use the port number from 0 ~ 65536 except 80. It’s recommended to use 88.
    • STEP3 : Make sure the information above is correct, and confirm the connection set to save the setting, and at the same time, you will return to the previous layer.

STEP4 : Select “Connect & View” again, and select the connection set you just created to start connecting to the device you want.

PDA

  • The setting interface of each PDA may vary depending on its individual brand. Therefore, the interface shown below only illustrates the main functions of the application. For the actual display, please refer to your own PDA.

With EagleEyes (For WinCE) installed

  • STEP1: Go to “Programs” “EagleEyes” to go to the setting page.
  • STEP2: Click “Device” to add a connection set, and key in the information necessary for DVR or network camera remote access.
  1. Label
    • Give a name for this connection set.
  2. (User Name)
    • Enter the user name used to access the DVR you want to connect.
  3. (Password)
    • Enter the password used to access the DVR you want to connect.
  4. IP
    • Enter the IP address or hostname (ex. dyndns) of the device you want to connect. 5. Port
    • Enter the port number used by the device you want to connect.
  • STEP3: Make sure the information above is correct, and confirm the connection set to save the setting, and at the same time, you will return to the previous layer.
  • STEP4: Select the connection set you just created to start connecting to the device you want.

With EagleEyes (For WinCE New version) installed

  • STEP1: Go to “Programs” -> “EagleEyes” to go to the setting page.
  • STEP2: Click “NEW DEVICE” to add a connection set, and key in the information necessary for DVR or network camera remote access.
  1. Name
    • Give a name for this connection set.
  2. Transfer Method
    • Select TCP or UDP.
  3. IP Address
    • Enter the IP address or hostname (ex. dyndns) of the device you want to connect. 4. Port
    • Enter the port number used by the device you want to connect.
  4. User Name
    • Enter the user name used to access the DVR you want to connect.
  5. Password
    • Enter the password used to access the DVR you want to connect.
  6. Stream Format
    • Select MPEG4, JPEG or H.264 (if available).
  7. AV Option
    • Select VIDEO, or VIDEO / AUDIO.
  • STEP3: Make sure the information above is correct, and confirm the connection set to save the setting, and at the same time, you will return to the previous layer.
  • STEP4: Select the connection set you just created to start connecting to the device you want.

AVAILABLE FUNCTIONS

  • When the installation is completed, you can start the remote surveillance via your device now. The functions available are depending on the remote device you have and the software you installed. For details, please refer to the following sections.

GPRS / 3G MOBILE PHONE

With GPRS / 3G software installed

  • a) DVR Mode
  • Single channel switch
  • 4-cut / 9-cut / 16-cut display mode switch
  • b) PTZ Mode
  • Hot point
  • Auto pan
  • Zoom in / out
  • Focus in / out

With EagleEyes (J2ME New version) installed DVR Mode

  • Single channel switch
  • 4-cut / 9-cut / 16-cut display mode switch
  • Quality changevelleman-Mobile-Phone-Surveillance-Software-FIG-8

WINDOWS Mobile

With EagleEyes (For WinCE) installed

  • a) DVR Mode
    • Single channel switch
    • 4-cut / 9-cut / 16-cut display mode switch
    • Snapshot
  • b) PTZ Mode (from left to right)
    • Preset point 1~16 selection (switch to DVR and click “CH”)
    • Focus near / far
    • Zoom in / out
    • Max Zoom in / out
    • Auto pan
    • Pan/tilt / zoom control

With EagleEyes (For WinCE New version) installed

a) DVR Mode

  • Record/playback at the remote site
  • Playback
  • Channel switch
  • Remote independent operation
  • 4-cut / 9-cut / 16-cut display mode switch
  • Quality change

b) PTZ Mode

  • A record at the remote site
  • Pan/tilt/zoom control
  • Auto pan
  • Auto Tracking
  • Focus near / far
  • Preset point 1~16 selection
  • http://www.eagleeyescctv.com/

Documents / Resources

| velleman Mobile Phone Surveillance Software [pdf] Installation Guide
Mobile Phone Surveillance, Software, Mobile Phone Surveillance Software
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals