BTI WIRELESS CPX80I 5G Industrial Outdoor CPE User Guide
- June 12, 2024
- BTI WIRELESS
Table of Contents
BTI WIRELESS CPX80I 5G Industrial Outdoor CPE
Welcome to the SRP Series
SRP series ruggedized outdoor router provides 5G NR service in a ruggedized form factor. With an operating temperature range of -40℃ ~ 70℃ endurance, they offer industrial-grade environmental qualifications while providing higher speed data services for video and other bandwidth-intensive applications. SRP series industrial router has very strong anti-vibration ability and it is qualified for extreme industrial environments and ideally suited for rail, transportation, mining, oil and gas, manufacturing, and other outdoor applications.
With the diverse self-developed 5G NR embedded modules integrated, SRP series industrial router can support multi-band for Private 5G NR, even support uncommon frequencies. SRP series industrial router can provide accurate real- time location information.
This document will serve as a quick start guide for SRP series ruggedized outdoor router. In this document, the SRP series ruggedized outdoor router will be replaced by the router.
Device Architecture
- Power port
- LAN1/WAN port
- RS232 and DIDO port
- LAN2 port
- RS485 port
- LED interface
- SIM interface
- Ground screws
- 5G NR antenna interface
- GNSS antenna interface
- No RF signals transmit
Note
- The reset button is beside SIM interface, if press 1s, router will restart; If press on for 10s, the router will reset to factory defaults.
- There are two white ground screws also at behind of device.
RS232/485 Cable Definition
RS232/485 cable definition
| Number| Colors| RS485| RS232+DIDO
1| Orange&white| NC| DO2
2| Orange| NC| DI2
3| Green&white| RS_GND| DO1
4| Blue| RS_GND| DI1
5| Blue&white| RS_GND| RS_GND
6| Green| RS_GND| RS_GND
7| Brown&white| RS485_B| RS232_TX
8| Brown| RS485_A| RS232_RX
LAN/WAN Cable Definition
LAN/WAN cable definition
| Number| Colors| LAN/WAN
1| Orange&white| MDI0+/RJ45-1
2| Orange| MDI0-/RJ45-2
3| Green&white| MDI1+/RJ45-3
4| Blue| MDI2+/RJ45-4
5| Blue&white| MDI2-/RJ45-5
6| Green| MDI1-/RJ45-6
7| Brown&white| MDI3+/RJ45-7
8| Brown| MDI3-/RJ45-8
Power Cable Definition
Power cable definition
| Number| Colors| PWR
1| Red| PWR_Positive
2| Black| PWR_GND
3| NC| NC
4| NC| NC
Hardware Configuration
Install SIM Cards
- Use a cross screwdriver to remove the SIM card cover.
- Slide the SIM cards into the SIM slots until they click into place. By default, the SIM card in slot 1 (the upper slot) is the Primary SIM card. When the SRP router is powered on or rebooted, it automatically connects to the network associated with the Primary SIM card.
- Re-attach the cover.
Connect and Turn on the Router
Please connect the protecting ground cable as first step, connect 9-36 VDC
power cable as the last step.
Connect to the Network
When the router is powered on, a green PWR LED may occur.
This indicates that the power input is good.
Once the router’ s radio module is configured for the SIM card, it begins the activation/provisioning process and attempts to connect to the mobile network. This process typically takes several minutes. A successful connection is indicated by a solid green NET LED. And the strength of the RF signal can be indicated by the Signal LEDs in different quantity.
| Indicator | Status | Description |
|---|
PWR
| Green| Power on
Off| No power supply
NET
| Green| Registered to network
Off| Not register to network
Blinking| Searching network
RSSI
| Green| Signal strong
Yellow| Signal good
Red| Signal weak
Off| No signal
Red Blinking| No SIM or SIM error
Software Configuration
Login to the Web Management Page
- Launch the web browser, enter http://192.168.1.1 in the address bar, and press Enter.
- Enter the username and password, and click Login.
- After the password is verified, you can login to the web management page.
The default username and password are both admin. If you want to view or
configure the router, you should use the super account to login to the web
management page. The default
super username is super admin, and the password is admin.
Radio Settings
- Choose Network > Radio Settings.
- On Radio Settings page, you can set the configuration of 5G NR network.
- In the 5G Status list, you can view the 5G NR status, such as Frequency, RSSI, RSRP, RSRQ,CINR, SINR, Cell ID and etc.
FAQs
The POWER indicator does not turn on.
- Make sure that the power cable is connected properly and the router is powered on.
- Make sure that the power supply is compatible with the router.
Fails to Login the web management page.
- Make sure that the router is powered on.
- Verify that the router is correctly connected to the computer through a network cable.
- If the problem persists, please contact the authorized local service suppliers.
The router fails to search for the wireless network.
- Check if the power supply is connected properly.
- Check if the router is placed in an open area that is far away from obstructions, such as concrete or wooden walls.
- If the problem persists, please contact the authorized local service suppliers.
The parameters are restored to default values.
- If the router is powered off unexpectedly while being configured, the parameters may be restored to the default settings.
- After configure the parameters, download the configuration file and restore the desired settings quickly.
The router does not support SIM card hot plug, please confirm that the
device is powered off when the SIM card is inserted or removed.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.