RILEY SCOOTERS RS3 Electric Scooter User Manual
- June 12, 2024
- RILEY SCOOTERS
Table of Contents
RS3 Electric Scooter
RS3 User Manual
1 2
RS3
Scan me
to unfold
3 4
Declaration of conformity
Type of device:
This declaration of conformity is issued under the sole responsibility
of the manufacturer.
Object of the declaraton:
Electric scooter
RS3
RILEY SCOOTER RS3
Model NO:
Description:
The object of the declaration described above is in conformity with
the relevant Union harmonisation legislation:
2011/65/EU amended by 2015/863(EU)
2014/30/EU
2014/35/EU
2006/42/EC
2014/53/EU
RoHS directive
EMC Directive
Low Voltage Directive
Machinery Directive
RED DIRECTIVE
Riley Scooters Limited: Kings Lodge, London Road, Sevenoaks,
TN15 6AR, United Kingdom
References to the relevant harmonize standards used or
references to other technical specification in relation to which
conformity is declared:
Name of manufacturer:
Importer/Distributor contact detail:
AUTHORISED SIGNATURE:
Hayden Riley
Founder & CEO
Date: 2022-10-28
www.rileyscooters.com
RILEY SCOOTERS LIMITED
Address: Kings Lodge, London Road, Sevenoaks, TN16 5AR,
United Kingdom
BS EN 17128:2020
EN 17128:2020
EN 60335-1:2012
EN 60335-2-29:2004
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN 61558-1:2005
EN 61558-2-16:2009
EN 55014-1:2021
EN 55014-2:2015
EN 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A1:2019
5 6
15-16
17-19
17
18
Charging instructions 19
20
21
22
9. 24
8. 23
Riley Scooter APP
10-14
10
11
12
13
14
Folding instructions
Unfolding instructions
7-8
7
7-9 The manufacturer recommends
riders be 14+ years old.
WARNING!
7 8
Max Loading: 120 kg.
9 10
Base plate latch Base plate clip
Brake lever
Handlebar release clasp
Accelerator / Throttle
Battery clip
Detachable battery
Charging port
Anti-slip mat
Fender clip
Fender
Tail light
Number plate
LED display
Folding latch
Stem folding Clip
Stem
Folding spanner
Motor
Kickstand
Discbrake
Handle
Headlight
11 12
brake lever to brake. Lightly
2.3 Unfolding instructions
1. Pull-out folding
latch to release
stem from base
plate.
clip
2. Pull stem up
till it’s vertical.
3. Pull stem into
place and secure
the folding
spanner.
5. Pull both
handle bars
upwards until
they click into
place.
4. Pull latch to
release the upper
stem. Fold stem
upwards till
vertical with the
lower stem.
6. Un-hook base
plate clip. Pull and
hold the base
plate latch.
7. While holding
latch, push the
folded deck
outwards till
aligned with
upper deck.
latch
8. Once in place,
secure the base
plate clip. Ensure
it’s fastened
tightly.
9. Push the deck
down to secure it
in place against
the rear fender.
View our
instructional
video here
Brake lever
13 14
1. Push down on
rear fender, pull up
the deck, and fold
towards the stem.
2. Press in button on
base plate clip, and
pull towards rear
fender to release.
1. Push Battery
clip in and hold.
2. Push the
battery up, away
from the bottom
of the stem.
1. Insert the battery
horizontally into the
pole, while pushing
the battery clip in.
2. When in, let go
of the battery clip,
and push battery
down until firmly
secure.
3. Pull and hold base
plate latch and push
the rear of the
scooter towards the
front wheel.
4. Fold the scooter
firmly till it’s secure.
Resecure the base
plate clip to original
position.
8. Slide folding latch
back, and align to the
hook on the base plate.
Release clip when
aligned to secure stem.
5. Pull handle bar
release claps as
arrows indicate, and
completely fold handle
bars toward stem.
6. Slide button
upwards and
unclip stem clasp,
fold stem towards
lower stem.
7. Slide button
upwards and
unclip folding
spanner. Fold stem
down to base plate.
2.4 Folding instructions
button
button
button
clip
latch
View our
folding
video here
15 16
lever to slow down or stop.
17 18
The instructions show you how to charge and maintain the battery and
provide some safety notices and the technical specifications. Please
use the battery properly according to these instructions to prolong
battery life and performance.
4.1 Battery parameters
Name Parameter
Type 5.8AH Battery
Charging time Approx. 2 hours
Voltage 36V
Working temperature 0°C – 35°C
Charging Temperature 0°C – 35°C
Max Charging Voltage 42V
Storage Time (at -10°C – 40°C) 3 months (full charge)
Initial Volume 5.8AH
Max Charging Current 2A
19 20
Product
Unfolded size 1181x540x1133mm
Folded size 649x272x474mm
Height from baseplate to ground 115mm
Net weight 16kg
Tyre size 8.5 inch pneumatic air tyre
with inner tube
Tyre pressure 35 P.S.I (2.41 Bar)
Waterproof level IPx4
Basic Information
Battery Capacity 36V/5.8 AH
Motor power 350W
Mileage per charge 15.5 miles (25km)
Max speed 15.5 mph (25km/h)
Max loading 120kg
Climbing angle 15°
Driving modes 3 (beginner, eco, sport)
Input voltage 100-240Vac
Frequency 50-60Hz
Output voltage 42V
Output current 1.5A
Store temperature -10°C-35°C
4.3 Charging instructions 1131mm
485mm
Charging
port
Battery
interface
Charging method 1:
Charging time is aprrox. 2 hours to fully charge.
Charging method 2:
21 22
Potential problem Solution
Unable to start up Check to see if the battery is charged.
Does not charge 1. Check whether the plugboard has
electricity.
2. Check the charger to see whether the
AC plug is connected (whether the
light is on).
3. Check the plug of the charger and
the charging port of the e-scooter
have been inserted correctly.
WARNING!
WARNING!
23 24
1x Copy of Manufacturer’s Limited Warranty
9. Riley Scooter APP
Stay on the move with our app which connects directly to your scooter
through Bluetooth. Get directions, view key riding info, and track your
rides effortlessly.
Features:
• Cockpit showing key riding info
• Lock and trace your scooter
• Track your rides
• Shop our range of accessories
Note: When connecting
to your scooter ensure
your Bluetooth is enabled
on your mobile device and
the scooter is turned on.
Scan to download the App. Alternativelly, go to
the Google Play Store (Android) or the Apple
App Store (iOS) and search Riley Scooters to
download and install the App.
Be advised there is a minimum
Android/iOS/Bluetooth version required. See
user materials for additional details.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio
or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference
that may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible
for
compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction