Guangzhou Magic Clip Technology Q88 Smart Car Mobile Phone Holder Instruction Manual

Guangzhou Magic Clip Technology Q88 Smart Car Mobile Phone Holder

Introduction

1. The clamp arm
2. High-grade glass panel
3. Infrared sensing region
4. LOGO light switch 5
5. Detachable foot rest
6. Front touch sensing switch

Function

This product adopts mute motor, the bottom noise is silent, easy to clamp the mobile phone, support wireless charging, mobile phone without wireless charging function Charging can also be connected to the magnetic suction head, automatic infrared induction, mobile phone close, the clamp arm can open, Intelligent locking, built-in large capacity battery, in case of power failure, still can use the electric opening and closing function.

Method of use

1. Charging function: wireless charging, charging on the phone; Magnetic suction charging, equipped with magnetic suction module, connected to the magnetic suction head can charge
2. Built-in battery: power off available, in the case of no wiring, can use electric open and close about 1000 times
3. Three kinds of induction: front infrared induction, touch induction; Back touch sensing
4. Detachable foot holder: if you do not want to use the bracket to charge, remove the magnetic foot holder and the data cable can be directly inserted into the phone to charge
5. Controllable light: Touch the light switch to control the light screen

Demolition method

1. The normal state is (Figure 1). If it needs to be disassembled to the state (Figure 2) Just grab the foot rest and pull it out for reassembly Align with the groove hole and push

Parameter

1. Model: Q88
2. Color: black/silver
3. Weight: About 128g net weight
4. Material: PC+ABS vacuum plating
5. input voltage/current: 5V12A,9V/1.67A
6. Magnetic head output power: 5-10W
7. Wireless charging output power: 15W, 10W, 7.5W, 5W automatic identification
8. Charging power: 113K-205khz
9. Charging distance: 0-8mm
10. Supported specifications: Comply with THE QI wireless protocol charging (including but not limited to the following mobile phones)
11. Support QC wireless fast charging devices, such as iPhone X/iphone8+, IPhone10 series, iPhone11 series, iPhone12 series, iPhone13 series, Huawei P30 series, Mate20Pro, Mate30 series, Mate40 series Samsung S6, S7, S8 series of wireless charging module mobile phones
12. Devices that do not support wireless charging must be connected to a magnetic suction head.
    Or remove the magnetic foot holder, mobile phone access data line charging

Directions for use

1. Installation position
   Air conditioning outlet or any smooth surface position

2. Connecting the power supply Connect the USB end of the data cable to the rechargeable port on the car (not to be built It is suggested to use the original USB interface of the car, and it is suggested to connect the car charging head.)

3. Infrared induction
   When the front of the object close to the equipment 5cm-20cm, infrared sensing Objects and supports automatically open their arms

4. Charging function
   After putting the phone into the device, the device will automati ally clamp the phone, and the bracket will be right Mobile phones with wireless charging function charge automati- cally.
   If the phone does not have wireless charging function, connect the magnetic head and aim again The magnet head can be charged by placing the support on the contact point

5. Touch sensing
   When removing the phone, touch the top bump on the back or tap the sensor button The stand automatically opens your arms and removes the phone

6. Built-in battery
   When fully charged, electric switch on and off can be used even without power supply About 1000 times

Pay attention to

1. Do not oversqueeze or hit the device.
2. Do not use the device in a high temperature, humidity, or corrosive environment Avoid damaging the circuit of the device.
3. You are advised to use a car charger to con- nect the power supply in the car.
   Directly connected to the car USB port, may appear slow charging Can’t charge and so on

FCC Rules

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a reside ntial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>