CODIUM LTE Outdoor Network CPE User Guide
- June 12, 2024
- CODIUM
Table of Contents
CODIUM LTE Outdoor Network CPE User Guide
Introduction
LTE outdoor CPE is a highly advanced LTE outdoor multi-service product
solution specifically designed to meet integrated data needs for residential,
business and enterprise users. The product nonsupport advanced Gigabit
networking functionality. It enables wide service coverage and provides high
data throughput and networking features to customers who rissoles easy
broadband access.
Panel of device
Packing List
Make sir you have everything you need to properly configure the device.
| | |
---|---|---|---
CDU| PoE| Power supply| Ethernet cable
| | |
m,“;’-“| Cable glands| Slotted end cap|
How does it work
- Conn act the Paar Adapter 1o Foe injector
- PoE Injector provides the power to ODU via LAN cable.
- PC connects LAN Cable to PoE. then PC can surf the Interment when DUO accesses the LET network.
This quick installation guicie shows you how 1o configure your ODU in ordler to access the Intrmet.
Configure hardware
CAUTION
Please make sure that you are familar with all accident prevention and safety procedures necessary for working at height and with electric- 1y before starting to instail the device. DO NOT install the ODU during a fighting smart.
Insert a SIM Card to the Slot
CAUTION
Make sure the ODE is tumned off before you Insert ‘your SIM card. It is recommended to NOT connect the Roe cable when you do this step, Otherwise, the SIM card may be damaged.
To connect the CAT Se (or above) Ethernet cable:
See the installation Instructions ta mount the ODU correeétly.
Step 1 CATSe {or above) cable 1o thread through the cabie glands: Step 2 Connect the end of the CATSs (or abave) Ethernat cable 1o the PoE port of the ODU. ‘Step 3 Wiring the cable glands fnto ODU and seal sightly.
NOTE: Muke sure you have inserte! the SIM card Into the ODU.
Header Connection
Mounting Bracket
NOTE: The DUO needs professional installation.
Choose a location
The GDU can be mounted on an antanna pole o mast or on a wal using the supplied mounting bracket.
To obtaln the best ragio signal level and connestion auality, the CPE antenna should be aimed towards the best eNB or BS directlyTo search for the best eNB direction, the Lser can rotate the CPE slowly and tiit CPE siightly to find the tiest signal direction. The CPE radio signal sirength fevel can be observed from the RF LEDS mounted on the lower panel as shown below. Different colores LEDS represent diferant signal streagir,
Connect the PoE
Pace a CATSe {or above) Ethemnet cable (not Included) from the location of your Intandad Router t0 the desired PC location
If you Intend o use cable clamps or other methods to secure the cable, do nat tighten them until you finish installing the Router and aou,
Step 1 Connect the CATSe (or above) Ethernet cable to FoE.
Da not connect to a computer or switch directly 1o the PoE port due to high PoE power.
Step 2 Connect the power adapter 1o the PoE injectar. The POWER LED
tums on a sofid green-ysfiow ooce conneated,
Step 3 Connect the inciuded Ethemet cable from the computer 10 one of
the Router’s EMemet pors.
LED Behavior
When satting up the Outdoor Uinit, the LED wil have the following Behavior
Configure the CPE
Login to the website
Use a browser to access the management web page to configute and manage the CAPE. The following procedure descries how 1o Use a computer running Windows 7 or above version and Interment Explorer to connect to they CAPE web page.
Step 1 Connect to the CPE correctly. Step2 Strt Intemat Explorer, type
HpJ/B2.168.0.1 In the addross bar. and press Entec
Step 3 Entar the usar name and password, and click Log in. You can connect to the management web page after the password s verified.
Configuration of LTE
‘Step 1 Connect 1o the CPE comectly. Step 2Go to the management website, Step 3 Chaose Settigs — Network — LTE Saftings. ‘Step 4 Sat the connection mode and scan mode.
The cofaun setting s automatio connestion and full tand sanhing, if you want to connect o the LTE retwork according o your needs, you can set the conneation mode as manual, and simply ‘scan @ specific band,
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure Imits set forth for an uncontralled environment. To comply with FCC RF Exposure compllance requirements, this grant Is applicabla to only Mable Configurations. The antennas used for the transmitter must be installed 1o provide a separution distarice of at least 20cm from al parsons and must fiot be co-located or operating n conjunction with any oiiver antenna or transmitier.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>