Vekesen D02 Music Remote Controller Scrolling Ring User Manual

Vekesen D02 Music Remote Controller Scrolling Ring

Packing List

Power on / off

Power on
Press and hold on the power button for 1 second the red and blue lights flash alternately

Power off
Press and hold on the power button for 5 seconds The red light keeps on for 2 seconds and then goes off when the ring powers on

Connect the cell phone

First Connection
The ring automatically enters the pairing state when it is powered on. At the same time please turn on the Bluetooth switch of your phone, then search for D02 in the Bluetooth list and click to connect If you can’t find the BT name Please turn off the BT switch and turn it on again to research Automatic Connection The ring automatically connects the last connected device after Power on

iPhone / iPad Settings
iPhone and iPad need to turn on the Assistive Touch button before it can be used normally Please see the below picture

Notes

1. Make sure the IOS software of your device is above 14.8
2. If you still can’t control the TikTok video after the touch button is turned on Please restart your device

Function (Video Mode)

• Single click: Pause

• Double click: Like

• Triple click: Continuous like on / off

• Press and hold for 1 second to release:

• Single click: Next video

• Double click: Swipe light

• Press and hold: Volume +

Take Picture / Record Video

In photo or video recording mode on your phone, Press any up or down button for seconds to take a photo or record video and end recording video Sigle clicks the left big button to focus
Notes

1. just support the original camera and various beauty cameras to take photos and record videos
2. When working Tiktok, long press is the function of volume increase and decrease

Switch mode
Switch between video mode and music mode

Notes

1. The initial mode is TikTok mode
2. When the ring is turned off, the last mode is saved
3. Page 7 shows how to operate in video mode
4. Page 10 shows how to operate in music mode

Function (Music Mode)

• Single click : Play / Pause / Answer / hang up call
• Double click : Call the last call
• Press and hold for 1 second: Refuse the call
• Press and hold for 1 second to release: Wake up / Undo Siri

• Single click : Next song
• Double click : Lock or Open screen
• Press and hold :Volume +

Charging Diagram

Automatic Shutdown

1. The ring automatically shuts down if it is not paired or if it is not paired again after 5 minutes of disconnection
2. The ring was connected to the phone for 30 minutes without any operation then the ring automatic shutdown

Question Guide

1. It doesn’t work on iPhone and iPad?
   iPhone and iPad need to turn on Assistive touch button before it can be used normally.

2. How to reset factory Settings?
   Press the power button five times quickly .

3. It cannot be used with beauty cameras?
   It only work the original camera and some beauty cameras to taking photos and recording videos.

4. iPhone and iPad cann’t swip up and down normally or can only pause the video after turning on the touch button and reset

Option 1
Check that the cursor point is in the middle of the screen after the ring is connected. if not in the middle, the solution is to slightly drag the “tracking Sensitivity Slider” in the following figure to the left or right. Press the power button of the ring to confirm every adjustment until the cursor point reaches the middle position or nearby and make sure that the “Perform Tousch Gestures” in the right figure is turned on and you can swipe the video up and down.

Option 2
As the following operations in sequence

1. Power off the ring and restart your cell phone
2. Turn on Assistive touch and appears a dot on the screen
3. Turn on the Bluetooth and connect the ring

Specification

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement
The device can be used in portable exposure condition without restriction

CONTACT

• Email to support
• 1301547734@qq.com
• (we will reply within 24 hours)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>