EAGLE G009MC 12V IP65 LED Tape light Kit Instructions

G009MC 12V IP65 LED Tape light Kit (with 5m PSU)
Instructions
G009MC (3000K)/G009ME (4000K)/G009MD (6000K)

G009MC 12V IP65 LED Tape light Kit

CONGRATULATIONS ON YOUR PURCHASE
Thank you for purchasing this Eagle Tape Light Kit. Please read these instructions carefully and leave them with the user of the product for future reference. If the product is sold on, then the instruction/manual should pass on as well.
BEFORE USE
You must inspect the product and all accessories including any cables and power supply for any signs of damage. If the product is damaged, DO NOT use it, and contact your supplier immediately.

PRODUCT SAFETY

• Children shall not play with the unit.
• Do not place the main lead beneath a carpet or a rug.
• Cleaning and user maintenance shall not be made by children without supervision.
• Please ensure the power supply is switched off when not in use.
• Do not leave this device switched on when unattended.
• Though the tape light section of this product is IP-rated any connections and its power supply are not and must be kept dry.
• Periodically check this product and its power supply for damage. If any is detected do not use it and contact your supplier.
• The power supply MUST be kept in a well-ventilated area away from sources of heat and moisture, such as a cooker and kettles.
• Never operate the light when fully wound as this may cause overheating.

INCLUDED IN THE BOX
1 x 5m Tape Light
1 x 12V 2A In-line power supply

OPERATION

• Installation must take place whilst the unit is unplugged
• The product MUST NOT be mounted using staples, nails, or metal fixings.
• The product can be cut at 5cm (3 LED) intervals to the required length, highlighted by a line straddled with a pair of scissors. This cut can be made with regular scissors (not supplied).
• The product can be installed in the desired location simply by removing the self-adhesive backing on the rear of the tape light and pressing the tape light against a smooth clean surface. The surface must be free of dust and grease.
• Apply firm pressure along the length of the tape light to ensure it has adhered in all locations.
• Once installed, plug the product in and switch the mains’ power on.

MAINTENANCE

There are no user-serviceable parts in this product. Periodically check the product for LED failure and damage. If any of the LEDs have failed or the product is damaged in any way switch off and disconnect from the mains supply. To clean the product, switch off and disconnect from the main supply. Using a slightly damp cloth gently wipe over. Do not use bleach, solvent-based cleaners, or strong detergents. These may damage the product and invalidate the warranty. If the mains lead is damaged, it must be replaced by the manufacturer or an authorized service center.

PAT TESTING

When used in an office environment, we recommend that this product should be safety-tested yearly by a qualified electrician (PAT Tested). We recommend that it is PAT tested regularly when used in a domestic environment.
GENERAL SAFETY REQUIREMENTS
Domestic wiring must be tested periodically by a qualified electrician at least once every 10 years or at every change of occupancy. For office and retail premises, and buildings such as village halls, the wiring must be inspected at least once every 5 years. It is recommended that all buildings be fitted with smoke alarms (it is mandatory for new buildings).

TECHNICAL SPECIFICATION

4000K (G009ME)
6000K (G009MD)

SERVICE WARRANTY

Electrovision Ltd. guarantees the product free from defects in materials and workmanship for a period of twelve months. Should this product be operated under conditions other than those recommended, or any attempts are made to service or modify the product, then the warranty will be rendered void. The product you buy may sometimes differ slightly from the illustrations.
This warranty is in addition to, and does not affect, your statutory rights. Our guarantee is administered by our retailers. If your product arrives damaged, you must contact the retailer from whom you bought it. The retailer’s contact details will be on the invoice that arrived with the product, or on the e-mail, you received when you placed the order. Do not contact Electrovision, only your retailer can arrange a replacement. If the product needs to be repaired or replaced, you must contact the retailer from whom you bought it. If you have just received your product and require technical help in using it, please call our Help Desk at (0845) 459 4816

Electrovision Ltd
Lots Lane
Sutton, St. Helens
Merseyside
WA9 3EX
www.electrovision.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>