hansgrohe 31559000 Waterforms M 70 CoolStart Washbasin Mixers Instruction Manual

: June 12, 2024
: hansgrohe

Table of Contents

hansgrohe 31559000 Waterforms M 70 CoolStart Washbasin Mixers
Product Information
Product Usage Instructions
Models
Safety Notes
Technical Data
Symbol Description
Installation Instructions
Adjustment
Dimensions
Flow diagram
Spare parts
Operation
Warranty
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

hansgrohe 31559000 Waterforms M 70 CoolStart Washbasin Mixers

.hansgrohe-31559000-Waterforms-M-70-CoolStart-Washbasin-Mixers-
product

Product Information

The product is a Waterforms faucet model available in three sizes: M 70 CoolStart 31559000, L 100 CoolStart 31574000, and XL 190 CoolStart 31578000. It is designed for bathing, hygienic, and body cleaning purposes. The faucet has a maximum operating pressure of 1 MPa, a recommended operating pressure of 0.1 – 0.5 MPa, and a test pressure of 1.6 MPa. It is important to note that the hot and cold water supplies must have equal pressures. The product is suitable for thermal disinfection and is exclusively designed for drinking water use.

The faucet comes with various features and accessories including a flow limiter, optional accessories (not included in the package), and spare parts. It is important to wear gloves during installation to prevent crushing and cutting injuries.

Product Usage Instructions

Before starting the installation, make sure to wear protective gloves to prevent any injuries.
Ensure that the hot and cold water supplies have equal pressures to avoid any issues.
Install the faucet according to the provided assembly instructions of the user manual.
Once installed, perform the necessary adjustments using the instructions, if needed. Note that adjusting the hot water limiter in combination with a continuous-flow water heater is not recommended.
To ensure proper operation, clean the faucet periodically as instructed of the user manual.
For any service or maintenance needs, refer to the user manual’s instructions.

Please note that these usage instructions are provided as a summary. For detailed information and specific steps, refer to the user manual provided with the product.

Models

.hansgrohe-31559000-Waterforms-M-70-CoolStart-Washbasin-Mixers-
fig-1

Safety Notes

Gloves should be worn during installation to prevent crushing and cutting injuries.
The product may only be used for bathing, hygienic and body cleaning purposes.
The hot and cold supplies must be of equal pressures.

Installation Instructions

Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured.
The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
The plumbing codes applicable in the respective countries must be observed.
The drain valve must only be used as intended. It is not allowed to attach other objects to the drain valve, for example a semi-pedestal.
If the instantaneous water heater causes problems or if you wish to increase the water flow, the EcoSmart® (flow limiter) located behind the aerator can be removed.

Technical Data

This mixer series-produced with EcoSmart® (flow limiter)

Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 – 0,5 MPa
Test pressure: 1,6 MPa
- (1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Thermal disinfection: 70°C / 4 min
The product is exclusively designed for drinking water!

Symbol Description

Do not use silicone containing acetic acid!
Adjustment
- To adjust the hot water limiter. Using a hot water limiter in combination with a continuous flow water heater is not recommended.
Dimensions
Flow diagram
Spare parts

Special accessories (order as an extra)

seal #98996000
Cleaning
Operation

Hansgrohe recommends not to use as drinking water the first half liter of water drawn in the morning or after a prolonged period of non-use.
After periods of prolonged non-use, but at least every third day, the fittings must be opened with the handle in hot and cold position to prevent stagnation in the connecting lines. Let the water run until the water temperature is constant.