NOTIFIER VM-1, AM-1, MPM-3 Meter Instruction Manual
- June 12, 2024
- NOTIFIER
Table of Contents
NOTIFIER VM-1, AM-1, MPM-3 Meter
Product Information
The Meter Assembly VM-1 / AM-1 / MPM-3 is a set of meters designed for use with the CHG-120 charger. It includes an ammeter (AM-1), a voltmeter (VM-1), or both (MPM-3) that can be installed to monitor the charging process. The meters come with the necessary cables and connectors for easy installation.
Optional Meters
| Item | Part Number | Description |
|---|---|---|
| Ammeter | AM-1 | 0-10 A ammeter with a 3 ft (.914 m) cable for connection to the |
charger at JP3. Mounts into a BB-55 battery box only.
Voltmeter| VM-1| 0-50 V voltmeter with 3 ft (.914 m) positive and negative
leads
for connection to the charger output circuit. Mounts into a BB-55
battery box only.
Ammeter and Voltmeter Assembly| MPM-3| An AM-1 and VM-1 are attached to a
mounting bracket. Mounts onto an
MPS-24A or MPS-400 power supply.
Product Usage Instructions
Installing an AM-1
- Mount the AM-1 ammeter into a BB-55 battery box.
- Connect the 3 ft (.914 m) cable of the AM-1 to the charger at JP3.
- Connect the positive and negative leads of the AM-1 to the battery terminals.
Installing a VM-1
- Mount the VM-1 voltmeter into a BB-55 battery box.
- Connect the positive and negative leads of the VM-1 to the charger output circuit.
Installing an MPM-3
Note:
The MPM-3 must be installed with the supplied mounting hardware.
- Remove any original mounting screws from either power supply’s PC board at the MPM-3 installation site.
- Mount the MPM-3 onto an MPS-24A or MPS-400 power supply using the provided mounting bracket.
Introduction
An ammeter (AM-1), or voltmeter (VM-1), or both (MPM-3) can be installed for use with the CHG-120 charger. Refer to Table 1 for descriptions of optional connectors on the charger. If mounting an AM-1 or a VM-1, mount the meter to a BB-55 as shown in Figure 2. If mounting an MPM-3, mount to a power supply (Figure 3) installed in a CAB-3. Table 1 contains descriptions and part numbers for these optional meters.
PART LIST
ITEM
| PART NUMBER|
DESCRIPTION
---|---|---
Ammeter
|
AM-1
| 0-10 A ammeter with a 3 ft ( .914 m) cable for connection to the charger at JP3. Mounts into a BB-55 battery box only.
Voltmeter
|
VM-1
| 0-50 V voltmeter with 3 ft ( .914 m) positive and negative leads for
connection to the charger output circuit. Mounts into a BB-55 battery box
only.
Ammeter and Voltmeter Assembly|
MPM-3
| An AM-1 and VM-1 attached to a mounting bracket. Mounts onto an MPS-24A or MPS-400 power supply.
Installation
Installing an AM-1
Perform the following steps to install an AM-1:
- Cut jumper JP9 on the charger (refer to Figure 1).
- Connect the AM-1 harness to JP3 on the charger (refer to Figure 1). Be sure to observe proper polarity.
- Mount the AM-1 into a mounting slot on the front of the BB-55 (refer to Figure 2).
Installing a VM-1
A VM-1 can be connected across a charger output circuit. For example, to
install a VM-1 to measure voltage from charger output circuit 2, perform the
following steps:
- Connect the positive lead to TB2 Out 2 (+) (refer to Figure 1).
- Connect the negative lead to TB2 Out 2 (–) (refer to Figure 1).
- Mount the VM-1 into a mounting slot on the front of the BB-55 battery box.
Installing an MPM-3
Perform the following steps to install an MPM-3:
- Connect the AM-1 (refer to Figure 1).
- Connect the VM-1 (refer to Figure 1).
- Mount the MPM-3 onto an MPS-400 or MPS-24A power supply (refer to Figure 3).
Note:
The MPM-3 must be installed with the mounting hardware supplied with it. Any
original mounting screws in either power supply’s PC board must be removed
from the MPM-3 installation site prior to installation of the MPM-3.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>