hansgrohe Blend Showerpipe, Shape Showerpipe Instruction Manual

**hansgrohe Blend Showerpipe, Shape Showerpipe Instruction Manual

**

Safety Notes

Gloves should be worn during installation to prevent crushing and cutting injuries.
The product may only be used for bathing, hygienic and body cleaning purposes.
The arm of the shower head is intended only to hold the shower head. Do not load it down with other objects!
Children as well as adults with physical, mental and/or sensoric impairments must not use this product without proper supervision. Persons under the influence of alcohol or drugs are prohibited from using this product.
Do not allow the streams of the shower touch sensitive body parts (such as your eyes). An adequate distance must be kept between the shower and you.
The product may not be used as a holding handle. A separate handle must be installed.
The hot and cold supplies must be of equal pressures.

Installation Instructions

• Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured.
• The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
• The plumbing codes applicable in the respective countries must be observed.
• The installation dimensions stated in these installation instructions are ideal for people of approximately 1800 mm in body height. The dimensions can be altered if required. In this case, pay attention to the fact that a change of installation height will also change the minimum height, and that the altered mounting dimensions must be taken into consideration.
• During installation of the product by qualified trained personnel, make sure that the entire fastening surface is even and smooth (no protruding seams or tile offset), that the finish of the wall is suitable to apply the product and has no weak points.
• The premounted dirt collection screen must be used to prevent dirt from entering through the pipes. Dirt entering can affect the function and/or lead to damage to the functional components of the fitting. Hansgrohe will not be held liable for any resulting damage.
• The product is not designed to be used with steam baths!
• If the continuous water heater causes any problems, or you have different water pressures you must install a water limiter to the cold supply, (ordered separately,article number 97510000).

Technical Data

Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 – 0,5 MPa
(26426670 / 26427670): 0,16 – 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Centre distance: 150±12 mm
Connections G 1/2: cold right – hot left

• Safety against backflow
• The product is exclusively designed for drinking water

Symbol description

Do not use silicone containing acetic acid!

Safety Function

The desired maximum temperature for example max. 42º C can be pre-set thanks to the safety function.

Adjustment

After the installation, the output temperature of the thermostat must be checked. A correction is necessary if the temperature measured at the output differs from the temperature set on the thermostat.

Thermal disinfection

Thermal disinfection pursuant to process sheet DVGW W 551 (≥ 70°C / > 3 min) must only be carried out by qualified personnel.

Maintenance

• The check valves must be checked regularly according to EN 806-5 in accordance with national or regional regulations (at least once a year).
• To guarantee the smooth running of the thermostat, it is necessary from time to time to turn the thermostat from total hot to total cold.

Dimensions

Vernis Blend Showerpipe 200 1jet
26276XXX / 26285000

Vernis Blend Showerpipe 200 1jet EcoSmart
26089XXX

Vernis Blend Showerpipe 200 1jet Green
26318000

Vernis Shape Showerpipe 230 1jet
26286XXX / 26287000

Vernis Shape Showerpipe 230 1jet EcoSmart
26097XXX

Vernis Shape Showerpipe 230 1jet Green
26319000

Flow diagram

1. Overhead shower
2. Hand showe

Vernis Blend Showerpipe 200 1jet
26276XXX / 26285000

Vernis Shape Showerpipe 230 1jet
26286XXX / 26287000

Vernis Blend Showerpipe 200 1jet EcoSmart
26089XXX

Vernis Shape Showerpipe 230 1jet EcoSmart
26097XXX

Vernis Blend Showerpipe 200 1jet Green
26318000

Vernis Shape Showerpipe 230 1jet Green
26319000

Vernis Blend Showerpipe 240 1jet
26426670

Vernis Blend Showerpipe 240 1jet EcoSmart
26428670

Vernis Shape Showerpipe 240 1jet
26427670

Vernis Shape Showerpipe 240 1jet EcoSmart
26429670

Vernis Blend Showerpipe 240 1jet
26426670

Vernis Shape Showerpipe 240 1jet
26427670

Vernis Blend Showerpipe 240 1jet EcoSmart
26428670

Vernis Shape Showerpipe 240 1jet EcoSmart
26429670

Spare parts

XXX = Colors
000 = Chrome Plated
670 = Matt Black

Vernis Blend Showerpipe 200 1jet
26276XXX / 26285000

Vernis Blend Showerpipe 200 1jet EcoSmart
26089XXX

Vernis Blend Showerpipe 200 1jet Green
26318000

Vernis Shape Showerpipe 230 1jet
26286XXX / 26287000

Vernis Shape Showerpipe 230 1jet EcoSmart
26097XXX

Vernis Shape Showerpipe 230 1jet Green
26319000

Vernis Blend Showerpipe 240 1jet
26426670

Vernis Blend Showerpipe 240 1jet EcoSmart
26428670

Vernis Shape Showerpipe 240 1jet
26427670

Vernis Shape Showerpipe 240 1jet EcoSmart
26429670

Special accessories

order as an extra

• tile-matching-disk #93813XXX
• extension 100 mm #94164XXX
• pipe 945 mm #93770XXX
• pipe 1145 mm #93907000

Cleaning

Cleaning recommendation / Warranty / Contact

http://www.hansgrohe.com/cleaning-recommendation

http://www.hansgrohe.com/cleaning-recommendation

http://www.hansgrohe.com/cleaning-recommendation

http://www.hansgrohe.com/cleaning-recommendation

Just clean: simply rub over the spray nozzles to remove lime scale.

Operation

open

hot

cold

close

Vernis Blend 26270XXX
Vernis Blend EcoSmart 26340XXX
Vernis Blend Green 26090000

To empty the overhead shower after use, hold it in a slightly inclined position.

Troubleshooting

pump has been installed
check to see if the pump is working).
– Regulator filter dirty| – Clean filter in front of the mixer and on the MTC- thermo cartridg
– Shower filter seal dirty| – Clean filter seal between shower and hose
Crossflow, hot water being forced into cold water pipe, or vice versa, when mixer is closed| Backflow preventers dirty or leaking

| – Clean backflow preventers, exchange if necessary
Spout temperature does not correspond with temperature set| – Thermostat has not been adjusted| – Adjust thermostat
– Hot water temperature too low| – Increase hot water temperature to 42 ºC to 60 ºC
Temperature regulation not possible| – thermo cartridge calcified| – Exchange thermo cartridge
Instantaneous heater didn’t work with thermostat| – Filters are dirty| – Clean the filter / exchange filter
– check valve hasn’t moved back| – Exchange check valves
– Flow limiter in handshower isn’t removed| – Remove flow limiter

Test certificate

References

• Taps for bathrooms, showers and kitchens | hansgrohe INT
• Web Server's Default Page
• Banyo ve mutfak için musluk ve armatürler
• Taps for bathrooms, showers and kitchens

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>