greenworks CRZ426 Pro Zero Turn Mower User Guide
- June 12, 2024
- Greenworks
Table of Contents
greenworks CRZ426 Pro Zero Turn Mower
Product Information
Product Name: EN ZERO-TURN MOWER
Model Number : 7400807AU CRZ426
Manufacturer : Greenworks Australia
Website :
www.greenworksaustralia.com
Email:
support@greenworksaustralia.com
Product Usage Instructions
Step 1: Tools Needed
The following tools are needed for assembly (not included):
- Wrench
- Scissor
- Tire Pressure Gauge
Step 2: Unpacking
When unpacking the mower, follow these instructions:
- Verify that any parts on the Loose Parts List are correctly assembled, properly tightened, and torqued correctly (where applicable).
- If any parts are damaged or missing, do not proceed with assembly until they are replaced with new original manufacturer’s parts or their equivalent.
- Position the mower on the frame bottom for assembly.
- Once assembly is complete, raise the cutting deck to its highest position.
- Position a ramp next to the frame bottom.
- Carefully drive the mower off the frame, using the brake pedal as needed to control the speed. Take caution to avoid loss of control and potential injury or property damage.
- If no ramp is available, drive the mower off the frame in reverse while looking down and behind. Avoid driving the mower off the frame in the forward direction without a ramp, as it may cause damage to the cutting deck.
Note: For any further assistance or inquiries, please contact support@greenworksaustralia.com.
RULES FOR SAFE ASSEMBLY
WARNING
Strictly adhere to all torque wrench tightening specifications. Failure to do
so could cause serious personal injury.
All information, illustrations, photographs, and specifications contained in this manual are based on the latest product information available at the time of publication. Due to improvements or other changes, there may be some discrepancies in this manual. We reserve the right to make product changes at any time, without notice and without incurring any obligation to make the same or similar changes to any products previously built or sold.
- Any person attempting to assemble this product must have proper training and experience. Read this manual carefully and follow all assembly procedures as described.
- All assembly must be completed with the unit on a level surface.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
WARNING
To avoid serious personal injury, do not attempt to use this product until you
have read this Own-er’s Manual thoroughly and understand it completely. If you
do not understand the warnings and instructions in this Owner’s Manual, do not
use this product.
For the contact,
support@greenworksaustralia.com
TOOLS NEEDED
The following tools (not included or drawn to scale) are needed for assembly:
UNPACKING
- Remove the bolts securing the corner and side braces to the frame bottom, then lift the braces to remove.
- Cut the nylon straps securing the front and rear wheel axles to the frame.
- Remove boxes containing loose parts, assembly hardware, and documentation. Remove and set aside all accessible packaging and wrap from unit and parts. Do not discard the packing material until you have carefully inspected and satisfactorily operated the product.
WARNING
If any parts on the Loose Parts List are already assembled to your product
when you unpack it, verify the part is assembled correctly, is properly
tightened, and is torqued correctly (where applicable) before proceeding to
the next assembly step. Use of a product that may have been improperly
assembled could result in serious personal injury.
- Inspect the product carefully to make sure no breakage or damage occurred during shipping.
NOTE: Mower should be assembled while positioned on the frame bottom. Once assembly is complete, raise the cutting deck to its highest position, then position a ramp next to the frame bottom and slowly and carefully drive mower off frame.
WARNING
Use care when driving the mower off of the frame and press the brake pedal
as needed to control the speed. The mower will freely roll if it is moved on
an inclined surface without pressing the brake pedal or setting the parking
brake. Failure to follow these instructions can result in loss of control and
result in death, serious personal injury, or property damage.
- If no ramp is available, slowly and carefully drive the mower off the frame in reverse while looking down and behind. Driving the mower off the frame in the forward direction without a ramp can cause damage to the mower’s cutting deck.
LOOSE PARTS LIST
WARNING
If any parts are damaged or missing do not assemble this product until the
parts are replaced with new original manufacturer’s parts or their equivalent.
Assembly of this product with damaged, missing, or incorrect parts could
result in serious personal injury.
ASSEMBLY
WARNING
- Strictly adhere to all torque wrench tightening specifications. Failure to do so could cause serious personal injury.
- Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.
- To prevent accidental starting that could cause serious personal injury, always remove the start key from the tool when you are assembling parts.
INSTALL THE BATTERY PACK
- Lift the seat panel.
- Lift the battery compartment cover.
- Install the battery pack into the battery compartment.
WARNING
Be careful for correct battery orientation. Do not force battery down if you feel high resistance.
NOTE
- Make sure that you install at least one battery in the battery compartment.
- Align the ribs of the battery with the battery port. Make sure that the battery latch clicks into the battery compartment smoothly.
INSTALL THE SEAT
- Place the seat assembly over the mounting brackets and align holes as shown.
- Connect the seat plug to the machine.
- Install the washers and nuts and tighten securely.
- Attach the sleeve to the nut.
- Make sure it is securely seated.
INSTALL THE MULCH COVER
The mower is configured for side discharge when shipped. If mulching is desired:
- Place the mulch cover on the tab on the mower housing.
- Align the holes in the mulch cover and the holes in the mower housing.
- Install and tighten the bolts, screws, fixation clamps and bearing ring as shown.
INSTALL THE STEER CONTROL LEVERS
- Lift one steering lever to align the holes in the steering lever with the holes in the corresponding mounting pole. Select the preferred steering lever operating height, and then use the wrench (13*16mm) to secure the steering lever as indicated below.
- Assemble the other steering lever and in the same way.
NOTE
- The left and right steering levers should be adjusted so that they align with each other when in the neutral position. NEVER install the steering levers in an asymmetrical operating height.
- Do not install the upper handle reversely.
FINAL PREPARATION
CHECK TIRE PRESSURE
Check the air pressure in all tires before use.
Improper air pressure will affect handling, steering response, traction, tire
life, level cutting, and operator comfort. Be sure tires are inflated to the
pressure shown below.
NOTE
Tire pressure should only be measured or adjusted when tires are cold.
WARNING
Check the tire pressure carefully while inflating.
Too much air in the tire could cause the tire to burst, causing serious
personal injury.
CHECK THE BATTERY CAPACITY
To verify mower batteries are fully charged, check the battery level
indicator. See battery manuals for details.
WARNING
To avoid accidental starting or movement of the mower that could result in
serious personal injury, always remove the start key and set the parking brake
when leaving the mower unattended.
NOTE
Always charge batteries after each use.
TEST THE SAFETY INTERLOCK SYSTEM
This mower features a Safety Interlock System to protect the operator by
shutting off the blades if the operator leaves the seat with the blades
running. Test the system to be sure it is working correctly.
TO TEST:
- Make sure direction control switch is in PARK position and PTO switch is down.
- Make sure the operator is on the seat.
Install start key and turn to ON ( ) position.
- Raise the PTO switch to activate blades.
- Briefly lift off the seat, but do not get off the mower.
The blades should shut off within 5 seconds. If they don’t, verify you connected the seat plug to the machine. If the plug is connected but the system still doesn’t function, contact customer service. Do not operate the mower until the safety interlock system has been repaired.
www.greenworksaustralia.com
support@greenworksaustralia.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>