viessmann 5578 Sound Module Jukebox User Manual

: June 12, 2024
: VIESSMANN

Table of Contents

viessmann 5578 Sound Module Jukebox
Important information
Safety instructions
Introduction
Connection
Troubleshooting
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

viessmann 5578 Sound Module Jukebox

viessmann-5578-Sound-Module-Jukebox-PRODUCT-IMG

Important information

Please read this manual completely and attentively before using the product for the first time. Keep this manual. It is part of the product.

Safety instructions

Caution

Risk of injury!
Tools are required for installation.
Electrical hazard!
Never put the connecting wires into a power socket! Regularly examine the transformer for damage. In case of any
damage, do not use the transformer.
Make sure that the power supply is switched off when you mount the device and connect the cables!
Only use VDE/EN-tested special model train transformers for the power supply!
The power sources must be protected to avoid the risk of burning cables.

Using the product for its correct purpose

This product is intended:
For installation in model train layouts and dioramas.
For connection to an authorized model train transformer (e. g. item 5200) or a digital command station.
For operation in dry rooms only.
Using the product for any other purpose is not approved and is considered inappropriate. The manufacturer is not responsible for any damage resulting from the improper use of this product.

Checking the package contents

Check the contents of the package for completeness:
Sound module with blue cable
Mounting material (2 screws, 8 plugs)
Manual

Introduction

Experience the model railway with all your senses: The stationary sound module provides the specific sounds to the scenes in the animated world. The sound module is equipped with an integral loudspeaker and a connection for an external loudspeaker.

Mounting

viessmann-5578-Sound-Module-Jukebox-FIG-1

Do not cover loudspeaker slots!
Mount the module with the loudspeaker on top!

Fasten the module with the enclosed screws. To ensure an optimal sound reproduction of the module, please note the following hints:

The loudspeaker is an integral part of the module. The upper surface of the module must always be uncovered in order to provide a good sound dispersion.
If possible, gear the sound module towards the spectator, so please avoid upside-down mounting under the layout.
The sound module should be installed near the respective functional model on your layout. You can also install the module on the layout, e. g. in a building. This way you can even have a better sound and an optimal concordance between the visible and the audible sound source.

Connection

Fitting cables: Due to the low current consumption thin cables can be used which can easily be hidden. It is recommended to use a cross-section of 0.14 mm² (e. g. Viessmann items 6860 – 6869 or 68603 – 68693).
For automatic operation (diorama mode) of the sound module, please refer to fig. 2 (section B). For manual operation of the sound module, please refer to fig. 2 (section A).
It is also possible to operate the sound module without the eMotion model “Jukebox”, item 1511.

viessmann-5578-Sound-Module-Jukebox-FIG-2

DC operation

Connect “Synchroneingang” to a pole of the power supply.
Connect “Synchroneingang” to a pole of the power supply.

DC operation

Brown cable: connect to the + pole of the power supply.
Yellow cable: connect to the – pole of the power supply.

Connection with a push-button

To operate the sound module with a push-button, please refer to fig. 2 (marking A).

After pushing the button, the first song is played (optionally with synchronous movement).
After pushing the button, the second song is played (optionally with synchronous movement).
After pushing the button, the third song is played (optionally with synchronous movement).
After pushing the button, the first song is played again (optionally with synchronous movement).
Etc.
Note: If you press the button while a song is playing, the sound module stops playing.

Connection with an on-off switch

To operate the sound module with an on-off switch, please refer to fig. 2 (marking B).
The sequence is the same as when using a push-button, but the songs are played automatically every two to three minutes.

Connection of an external loudspeaker
The sound module is equipped with an output for an external loudspeaker with electrical values of 8-ohm impedance at least and min. 1-watt power (can be purchased in a specialized shop for electronics). In case you connect an external loudspeaker the integral loudspeaker will be switched off.

Please pull the sound module’s short blue cable out of the next socket to the right.
Insulate the blue cable to avoid any contact with other cables.
Mount the external loudspeaker to the intended place.
Lay the two wires of the external loudspeaker to the sound module.
Connect the two wires to the two sockets according to fig. 3.

Volume adjustment

The sound module is equipped with a volume control for the sound. The adjustment is valid both for the integral loudspeaker and for an external loudspeaker.
To adjust the volume, use a slotted screwdriver and proceed as follows (see fig. 4):
Increase volume: Turn the poti to the right.
Reduce volume: Turn the poti to the left.

Use a small screwdriver!

viessmann-5578-Sound-Module-Jukebox-FIG-4

Troubleshooting

All Viessmann products are produced with high-quality standards and are checked before delivery. Should a fault occur notwithstanding, you can do a first check.
Please check first the power supply and the wiring.
No sound from the module. No sound from the external loudspeaker.
The sound module has to be connected acc. to fig. 2. If the synchronous input is not connected as shown in the figures, playing of the sound will not be possible!
Turn the pot to the right.
Please make sure that the small blue plug at the housing of the sound module is removed from the socket and is insulated.
Connect the external loudspeaker as shown in fig. 3.
If you are unable to find and fix the cause for the problem please contact our service department (service@viessmannmodell.com). Please send the item to the Viessmann service department for check and repair only after consultation.