EGOLUCE 1506 Mork Sistema Design ABS Studio Instruction Manual
- June 12, 2024
- EGOLUCE
Table of Contents
EGOLUCE 1506 Mork Sistema Design ABS Studio
Product Information
- Product Name: Mork
- Product Model: art. 1506
- Manufacturer: EGOLUCE s.r.l.
- Origin: Italy
- Product Type: Luminaire
- Power: max 1400 mA – 3.4W DC
- Color Temperature: 3000 K
- Class: Class III
- Efficiency Class: F (Energy efficiency class F according to EU2019/15)
Product Usage Instructions
Geometric Configuration:
To create geometric configurations using Mork, follow these steps:
- Connect the Mork units using the connectors (art. 0507).
- Attach the Mork units to the ceiling using the ceiling rose (Rosone).
- For configurations with 3 Mork units, use 3 art. 1506 units (Mork) and include the connector.
In-Line Configuration:
To create in-line configurations using Mork, follow these steps:
- Connect the Mork units using the connectors (art. 0507).
- Attach the Mork units to the ceiling using the ceiling rose (Rosone).
- For configurations with 2 Mork units, use 2 art. 1506 units (Mork) and include the connector.
- Include 1 art. 0506 unit (Rosone) in the configuration.
Linear Configuration:
To create linear configurations using 2, 4, or 6 Mork units, follow these steps:
- Connect the Mork units using the connectors (art. 0507).
- Attach the Mork units to the ceiling using the ceiling rose (Rosone).
- Include the accessory (art. 0507) for linear configurations.
Connector Mounting:
For connector mounting, follow these steps:
- Fix the connector using screws.
- Connect the wires as follows:
- Red wire to the “+” terminal.
- Black wire to the “-” terminal.
System Regulation:
To regulate the system, follow these steps:
- Connect the wires as follows:
- Red wire to the “+” terminal.
- Black wire to the “-” terminal.
- Adjust the system according to your preference.
Installation with Central Ceiling Rose:
To install Mork with a central ceiling rose, follow these steps:
- Attach the Mork units to the ceiling using the central ceiling rose (Rosone).
Important Notes:
- Do not tighten the screws too strongly during connector mounting.
- This product contains a light source of energy efficiency class F according to EU2019/15. If the light source needs replacement, it should be done immediately.
- This product is suitable for installation on normally inflammable surfaces.
- Dispose of this product correctly to protect the environment. Contact your local authority, household waste disposal service provider, or the shop where you purchased the product for recycling information.
INSTALLATION INSTURECTION
Legenda:
Examples of geometric configuration
Examples of in line configuration
This equipment is guaranteed only if used as indicated in these instructions: preserve this instruction. Before any operation on this equipment, disconnect the power supply Installation must be made by qualified persons. For a correct assembling see the here enclosed diagram. In order to grant a constant current, all leds must be connected in series, an eventual parallel connection commonly used for halogen lamps destroys the leds in a short time. The power supply cable of the device cannot be replaced, if the cable has been damaged the entire device shall be replaced immediately. This product contains a light source of energy efficiency class F. EU2019/15 RAEE Symbol (Waste Electrical and Electronic Equipment). The use of the RAEE symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help protect the environment. For more detailed information about the recycling of this product, please contact your local authority, your household waste disposal service provider or the shop where you purchased the product.
CONTACT
- EGOLUCE s.r.l. – via I.
- Newton, 12 – 20016 Pero, Milano – Italy
- Tel. +39 02339586.1
- Fax +39 023535112
- www.egoluce.com.
- info@egoluce.com.