hansgrohe 26276XXX Vernis Blend Showerpipe Instruction Manual

June 12, 2024
hansgrohe

Instructions for use
Assembly instructions

26276XXX Vernis Blend Showerpipe

hansgrohe 26276XXX Vernis Blend Showerpipe - Figrue 1

Vernis Blend
Showerpipe 200 1jet
26276XXX / 26285000
Vernis Blend Showerpipe 200
1jet EcoSmart
26089XXX
Vernis Blend Showerpipe 200
1jet Green
26318000

Vernis Blend
Showerpipe 240 1jet
26426670
Vernis Blend Showerpipe 240
1jet EcoSmart
26428670hansgrohe 26276XXX Vernis Blend Showerpipe - Figrue
3

Vernis Shape
Showerpipe 230 1jet
2628 6XXX / 26287000
Vernis Shape Showerpipe 230
1jet EcoSmart
26097XXX
Vernis Shape Showerpipe 230
1jet Green
26319000 Vernis Shape
Showerpipe 240 1jet
26427670
Vernis Shape Showerpipe 240
1jet EcoSmart
26429670

Safety Notes

Gloves should be worn during installation to prevent crushing and cutting injuries.
The product may only be used for bathing, hygienic and body cleaning purposes.
The arm of the shower head is intended only to hold the shower head. Do not load it down with other objects’
Children as well as adults with physical, mental and/or sensoric impairments must not use this product without proper supervision. Persons under the influence of alcohol or drugs are prohibited from using this product.
Do not allow the streams of the shower touch sensitive body parts (such as your eyes). An adequate distance must be kept between the shower and you.
The product may not be used as a holding handle. A separate handle must be installed.
The hot and cold supplies must be of equal pressures.

Installation Instructions

  • Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be
  • The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
  • The plumbing codes applicable in the respective countries must be observed.
  • The installation dimensions stated in these installation instructions are ideal for people of approximately 1800 mm in body height. The dimensions can be altered if required. In this case, pay attention to the fact that a change of installation height will also change the minimum height, and that the altered mounting dimensions must be taken into consideration.
  • During installation of the product by qualified trained personnel, make sure that the entire fastening surface is even and smooth (no protruding seams or tile offset), that the finish of the wall is suitable to apply the product and has no weak
  • The premounted dirt collection screen must be used to prevent dirt from entering through the pipes. Dirt entering can affect the function and/or lead to damage to the functional components of the Hansgrohe will not be held liable for any resulting damage.
  • The product is not designed to be used with steam baths’
  • If the continuous water heater causes any problems, or you have different water pressures you must install a water limiter to the cold supply, (ordered separate­ly,article number 97510000).

Technical Data

Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 – 0,5 MPa
Test pressure: 1,6 MPa

(1 MPa = 10 bar = 147 PSI)
Hot water temperature:| max. 60°C
Centre distance:| 150±12 mm
Connections G 1/2:
• Safety against backflow
• The product is exclusively designed for drinking water!| cold right – hot left

Symbol description

Do not use silicone containing acetic acid!
Safety Function
The desired maximum temperature for example max. 42º C can be pre-set thanks to the safety function.
Adjustment
After the installation, the output temperature of the thermostat must be checked. A correction is necessary if the temperature measured at the output differs from the temperature set on the thermostat.
Thermal disinfection
Thermal disinfection pursuant to process sheet DVGW W 551 (≥ 70°C / > 3 min) must only be carried out by qualified personnel.
Maintenance

  • The check valves must be checked regularly according to EN 806-5 in accordance with national or regional regulations (at least once a year).
  • To guarantee the smooth running of the thermostat, it is necessary from time to time to turn the thermostat from total hot to total cold.

Dimensions
Flow diagram 

  • Overhead shower
  • Hand shower

Spare parts
XXX = Colors
000 = Chrome Plated
670 = Matt Black

Special accessories
order as an extra

| •tile-matching-disk #93813XXX
---|---
•extension 100 mm #94164XXX
•pipe 945 mm #93770XXX
•pipe 1145 mm #93907000
Cleaning
Operation

To empty the overhead shower after use, hold it in a slightly inclined position.
Test certificate

Fault Cause Remedy
Insufficient water – Supply pressure inadequate – Check water pressure (If a

pump has been installed check to see if the pump is working).
– Regulator filter dirty| – Clean filter in front of the mixer and on the MTC- thermo cartridge
– Shower filter seal dirty| – Clean filter seal between shower and hose
Crossflow, hot water being forced into cold water pipe, or vice versa, when mixer is closed| – Backflow preventers dirty or leaking| – Clean backflow preventers, exchange if necessary
Spout temperature does not correspond with temperature set| – Thermostat has not been adjusted| – Adjust thermostat
– Hot water temperature too low| – Increase hot water temperature to 42 °C to 60 °C
Temperature regulation not possible| – thermo cartridge calcified| – Exchange thermo cartridge
Instantaneous heater didn’t work with thermostat| – Filters are dirty| – Clean the filter / exchange filter
– check valve hasn’t moved back| – Exchange check valves
– Flow limiter in handshower isn’t removed| – Remove flow limiter

Assembly

hansgrohe 26276XXX Vernis Blend Showerpipe - Figrue 5hansgrohe 26276XXX Vernis Blend Showerpipe - Figrue
6

hansgrohe 26276XXX Vernis Blend Showerpipe - Figrue 7

Vernis Blend
Showerpipe
200 1jet
EcoSmart
26089XXX| Vernis Shape
Showerpipe
230 1jet
EcoSmart
26097XXX| Vernis Blend
Showerpipe
200 1jet
26276XXX| Vernis Shape
Showerpipe
230 1jet
26286XXX| Vernis Blend
Showerpipe
200 1jet
Green
26318000| Vernis Shape
Showerpipe
230 1jet
Green
26319000
---|---|---|---|---|---
hansgrohe 26276XXX Vernis Blend Showerpipe - Figrue 8
Vernis Blend
Showerpipe
240 1jet
26426670
Vernis Shape
Showerpipe
240 1jet
26427670| Vernis Blend
Showerpipe
240 1jet
EcoSmart
26428670
Vernis Shape
Showerpipe
240 1jet
EcoSmart
26429670
---|---

Hansgrohe · Auestraße 5 – 9 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282 · Telefax +49 (0) 7836/511440
E-Mail: info@hansgrohe.com · Internet: www.hansgrohe.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

hansgrohe User Manuals

Related Manuals