hansgrohe Shower Fitting Rebris S Installation Guide
- June 12, 2024
- hansgrohe
Table of Contents
Shower Fitting Rebris S
Installation Guide
Safety Notes
Gloves should be worn during installation to prevent crushing and cutting
injuries.
The product may only be used for bathing, hygienic and body cleaning purposes.
The hot and cold supplies must be of equal pressures.
Installation Instructions
- Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honored.
- The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
- The plumbing codes applicable in the respective countries must be observed.
Technical Data
Operating pressure: | max. 1 MPa |
---|---|
Recommended operating pressure: | 0,1 -0,5 MPa |
Test pressure: | 1,6 MPa (1 MPa = 10 bar = 147 PSI) |
Hot water temperature: | max. 60°C |
Thermal disinfection: | 70°C / 4 min |
The product is exclusively designed for drinking water!
Symbol description
| Do not use silicone containing acetic acid!
---|---
| Adjustment (see page 36)
To adjust the hot water limiter. Using a hot water limiter in combination with
a continuous flow water heater is not recommended.
| Maintenance (see page 38)
| Dimensions (see page 40)
| Flow diagram (see page 41) free flow
| Spare parts (see page 42)
| Special accessories (see page 42)
order as an extra
• extension 25 mm #13595000
• Extension Set 22 mm (when wall is not deep enough)#15597XXX, #13597XXX,
13596000, #13593XXX
| Cleaning (see page 37)
| Operation (see page41)
| Test certificate (see page 48)
Fault| Cause| Remedy
---|---|---
Insufficient water| – EcoSmart® dirty or leaking| – Clean or exchange
EcoSmart® (see page 38)
Mixer stiff| – Cartridge defective, calcified| – Exchange cartridge
Mixer dripping| – Cartridge defective| – Exchange cartridge
Hot water temperature too low, no cold water. Instantaneous water heater
starts up when cold water is selected.| – Hot water limiter incorrectly set| –
Set hot water limiter
– Crossflow| – Exchange cartridge
Assembly (see page 34)
http://www.hansgrohe.com/cleaning-recommendation
Cleaning recommendation / Warranty / Contact
|
---|---
|
|
|
|
| P-IX| DVGW| SINTEF| NF| | ETA| **
---|---|---|---|---|---|---|---
14165000| | | | | X| X|
15665XXX| PA-IX 9710/IB| CQ0125| | | X| X|
31365XXX| PA-IX 9710/IB| CQ0125| | | X| X|
31456000| PA-IX 9710/IB| CQ0125| | | X| X|
31665000| PA-IX 9710/IB| CQ0125| | | X| X|
31685000| PA-IX 9710/IB| CQ0125| | | X| X|
31965000| PA-IX 9710/IB| CQ0125| | X| X| X|
32565XXX| PA-IX 9710/IB| CQ0125| | | X| X|
32675XXX| PA-IX 9710/IB| CQ0125| | | X| X|
71065000| | CQ0125| | | X| | **
71267000| PA-IX 9710/IB| CQ0125| | | X| X
71365000| | CQ0125| | | X|
71603000| | CQ0125| | | |
71605000| PA-IX 9710/IB| CQ0125| | X| X| X
71667XXX| PA-IX 9710/IB| | | | |
71668XXX| PA-IX 9710/IB| | | | | |
71765XXX| PA-IX 9710/IB| CQ0125| | | X| X
72605000| PA-IX 9710/IB| CQ0125| | | X| X
72667XXX| PA-IX 38261/IA| DN0343| | | |
72668XXX| PA-IX 38261/IA| DN0343| | | |
74565000| PA-IX 9710/IB| CQ0125| | | X| X
75615XXX| PA-IX 9710/IB| DM0707| | | |
76615XXX| PA-IX 9710/IB| | | | |
Auestraße 5 – 9
D-77761 Schiltach
Telefon +49 (0) 78 36/51-1282
Telefax +49 (0) 7836/511440
E-Mail: info@hansgrohe.com
Internet: www.hansgrohe.com
08/2022
9.08418.22