HyperX 4P5E2AA DuoCast USB Microphone User Guide
- June 4, 2024
- HYPERX
Table of Contents
DuoCast USB Microphone
User Guide
Overview
A – Tap-to-mute sensor
B – LED ring
C – Gain control knob
D – Multifunction button
E – Headphone output
F – USB-C port
G – USB-C to USB-A cable
H – Mount adapter
*Supports both 3/8” and 5/8” thread sizes
Using with PC, Mac, PS5, or PS4
Connecting Headphones
Connect headphones to the headphone jack on the microphone for microphone
monitoring and playback audio.
Selecting a Microphone Polar Pattern
Push the multifunction button to switch between the microphone’s two polar patterns, indicated by the LED ring.
| LED RING | POLAR PATTERN | SOUND DIRECTION |
|---|---|---|
| Full to front |
Front to full| |
Adjusting Microphone Gain
Muting the Microphone
Tap the tap-to-mute sensor to mute/unmute the microphone. The LED ring will
toggle to indicate the change in mute status.
Turning Microphone Monitoring On/Off
To turn microphone monitoring on/o¦, press and hold the multifunction button
and tap the tap-to-mute sensor= Installing the Mount Adapter
- Remove both the thumb screw and nut from the microphone stand.
- Remove the microphone stand from the microphone.
- Align the mount adapter with the microphone mount holes and secure the adapter with the thumb screw and nut.
HyperX INGENUITY Software
To customize lighting, download the HyperX INGENUITY software at :
hyperxgaming.com/ngenuity
Questions or Setup Issues?
Contact the HyperX support team or see the user manual at
hyperxgaming.com/support/microphones
Maintenance
Cleaning the microphone
- Unplug all cables from the microphone before cleaning.
- Put a very small amount of mild all-purpose cleaner on a soft cloth.
- Wipe down the external surface of the microphone. Avoid getting any moisture in the microphone holes.
- Let the surface of the microphone dry completely before use.
• Do not use harsh cleaners such as products containing bleach.
• Do not use compressed air and spray into the microphone.
Product Specification
Microphone
| Power consumption: | 5V 220mA (white light) |
|---|---|
| Sample/bit rate: | 96kHz/24bit |
| Element: | Electret condenser microphone |
| Condenser type: | Two 14mm condensers |
| Polar patterns: | Cardioid, Omnidirectional |
| Frequency response: | 20Hz—20kHz |
| Sensitivity: | -11dBV (1V/Pa at 1kHz) |
| Cable length: | 2000±50mm |
| Weight: | 502.9±5% |
| Lighting: | RGB (16,777,216 colors) |
| Light e¦ects: | 2 zone |
| Connection type: | USB-C to USB-A |
Headphone Output
| Impedance: | 32 |
|---|---|
| Frequency response: | 20Hz – 20kHz |
| Maximum power output: | ≥7mW |
| THD: | ≤0.05% (at 1kHz/0dBFS) |
| SNR: | ≥100dB (at 1kHz/0dBFS, A-wt) |
Nomor Registrasi di
Kementerian Perdagangan: IMKG.1806.11.2021
Importer: PT Hewlett-Packard Indonesia
Alamat: Gedung Perkantoran Prudential Center Kota Kasablanka, Lt 9, Unit
A-H,Jl. Casablanca Kav. 88, Kel. Menteng Dalam, Kec. Tebet, Kota Adm Jakarta
Selatan 12870
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class digital device,
according to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o¦ and on, thare e
users are encouraged to try correct the interference by one or more of the
following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Any special accessories needed for compliance must be specified the instruction manual.
Warning:
A shielded-type power cord is required in order to meet FCC emission limits
and also to prevent interference to the nearby radio and television reception.
It is essential that only the supplied power cord be used. Use only shielded
cables to connect I/O devices to this equipment.
CAUTION:
Any changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
India RoHS Statement
This product, as well as its related consumables and spares, complies with the
reduction in hazardous substances provisions of the “India E-waste Rule 2016.”
It does not contain lead, mercury, hexavalent chromium, polybrominated
biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1
weight % and 0.01 weight % for cadmium, except where allowed pursuant to the
exemptions set in Schedule 2 of the Rule. Turkey WEEE Statement
****HyperX and the HyperX logo are registered trademarks or trademarks of HP
Inc. in the U.S. and/or other countries.
All registered trademarks and trademarks are property of their respective
owners.
HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA. HP, HQ-TRE, 71025
Boeblingen, Germany. HP Inc UK Ltd, Regulatory
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>