HUMMINBIRD 532966-1 MEGA Live Targetlock Foot Pedal Installation Guide

MEGA LIVE TARGETLOCK FOOT PEDAL
Installation Guide

Overview

Following are instructions for the installation of this accessory. Before you start installation, we encourage you to read these instructions carefully in order to get the full benefit from your Humminbird® accessory.
Supplies: In addition to the hardware included with your accessory, you will need the following supplies: a pencil or similar marking tool and a drill with a #2 Phillips driving bit.
Technical Support: Contact Humminbird Technical Support through our Help Center at https://humminbird-help.johnsonoutdoors.com/hc/en-us.

Installation Preparation

Before mounting your MEGA Live Imaging TargetLock foot pedal, please give consideration to the following:

• Examine your boat to ensure that you will not drill into any obstructions and that the hardware will be accessible for assembly.
• Make sure the area under the mounting location is flat, clear to drill holes and that the installation hardware will not damage existing components below the mounting surface. It may be necessary to shim or modify the mounting surface under the  ounting location to create a flat area for the foot pedal to be mounted.
• Mount the foot pedal in an area that has a clear line of communication with your Humminbird control head.
• Mount the foot pedal in an area where it will not become a tripping hazard.

Install the Foot Pedal

1. Once you have selected a mounting location for your foot pedal, remove the foot pedal from the base by squeezing the tabs on both sides of the foot pedal and pulling the pedal and base apart.

2. Position the base at the selected location and mark the mounting holes with a pencil or similar marking tool.
   NOTE: The base has three mounting holes that are used to secure it to the boat. The bottom side of the base has three pads around the mounting holes. These pads should be placed facing down when the base is installed.

3. Place one of the three (3) provided #8 screws in each of the mounting holes of the base. Make sure the mounting holes still line up with the marked locations and then use a drill with a #2 Phillips driving bit to secure the base to the deck of the boat. Do not overtighten.
   Separating the Foot Pedal and Base Securing the Base to the Deck

4. Once the base is installed, reattach the foot pedal to the base. Make sure the tabs on the pedal click into place and that the pedal is fully seated on the deck of the boat.

Pair the Foot Pedal to the Control Head

Use the following instructions to pair the wireless foot pedal to the Humminbird control head. For more information about setting up your foot pedal or your MEGA Live TargetLock, see the MEGA Live Imaging Operations Guide.

APEX/SOLIX Series

1. Press the HOME key.
2. Select Settings > CHIRP Sonar > MEGA Live > Pair TargetLock Foot Pedal.
3. On your foot pedal, press and hold the Left button and the Right button at the same time until the LEDs at the top of the pedal begin to scroll. Then release the buttons.
4. The control head and the foot pedal will go into Pairing Mode. If 30 seconds pass while in Pairing Mode and they do not successfully pair, an error message will display signaling that the pairing has timed out. Repeat the procedure.

NOTE: After pairing completes, if the lights on the foot pedal blink in a scrolling pattern, this indicates that the control head is updating the foot pedal. When the software update is complete, the pairing process will need to be repeated.
NOTE: You can check the MEGA Live Device List to confirm that the footpedal is paired. Select Home > Settings > CHIRP Sonar > Device List.

HELIX Series

1. Main Menu: On your control head, press the MENU key twice.
2. Select the Accessories tab > MEGA Live > MEGA Live Installation.
3. Select Pair TL Foot Pedal, and press the RIGHT Cursor key.
4. On your foot pedal, press and hold the Left button and the Right button at the same time until the LEDs at the top of the pedal begin to scroll. Then release the buttons.
5. The control head and the foot pedal will go into Pairing Mode.
   If 30 seconds pass while in Pairing Mode and they do not successfully pair, an error message will display signaling that the pairing has timed out. Repeat the procedure.
   NOTE: After pairing completes, if the lights on the foot pedal blink in a scrolling pattern, this indicates that the control head is updating the foot pedal. When the software update is complete, the pairing process will need to be repeated.
   NOTE: You can check the MEGA Live Device List to confirm that the foot pedal is paired. Press the MENU key twice to open the Main Menu. Select the Accessories tab > MEGA Live > Device List.

WARNING
THIS PRODUCT CONTAINS A BUTTON BATTERY.
If swallowed, a lithium button battery can cause severe or fatal injuries within 2 hours. Keep batteries out of reach of children. If you think batteries may have been swallowed or placed inside any part of the body, seek immediate medical attention.
NOTE: Download Humminbird installation guides and operations manuals from our Web site at humminbird.com
NOTE: Product specifications and features are subject to change without notice.

Contact Humminbird
Contact Humminbird Technical Support through our Help Center at <https ://humminbird-help.johnsonoutdoors.com/hc/en-us> or in writing to the address below:

Humminbird Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
© 2023 Johnson Outdoors Marine Electronics, Inc. All rights reserved.

Documents / Resources

| HUMMINBIRD 532966-1 MEGA Live Targetlock Foot Pedal [pdf] Installation Guide
532966-1 MEGA Live Targetlock Foot Pedal, 532966-1, MEGA Live Targetlock Foot Pedal, Targetlock Foot Pedal, Foot Pedal
---|---

References

• humminbird.com
• johnsonoutdoors.com/hc/en-us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>