OSEE TX401-B 15.4 Inch 10bit 800nits HDR Field Studio Production Monitor User Manual

OSEE TX401-B 15.4 Inch 10bit 800nits HDR Field Studio Production Monitor

Product Information

The TX401-B/TX402-B Quad Split is a video processing device manufactured by OSEE TECHNOLOGY LTD. It is designed to support multiple signal inputs and outputs, providing users with various display modes and control options.
The TX401-B model features 4CH HDMI Video Input and 4CH GPI Input, with 1CH SDI Video Output and 1CH HDMI Video Output. On the other hand, the TX402-B model offers 4CH SD/HD/3G-SDI Video Input and 4CH GPI Input, with 1CH SDI Video Output and 1CH HDMI Video Output.

Key Features:

• Supports 4 channels of signal inputs with LED indicators and one power input indicator
• Supports four kinds of output formats: 1080P50, 1080P59.94, 1080I50, 1080I59.94
• Supports four kinds of screen display modes: four uniform size screens, one big left with three right small, one big right with three left small, one big top with three bottom small
• Supports TSL3.1/4.0, TSL5.0 protocol
• 4ch GPI interfaces, one RS-422 interface, one ETHERNET interface
• Embedded Web Server, supports web interview

Product Usage Instructions

Control Buttons and Interfaces

The device has control buttons, interfaces, and indicators located on both sides.

Inputs and Outputs:

• HDMI Input: Located on the right side, labeled as HDMI IN1, HDMI IN2, HDMI IN3, HDMI IN4
• HDMI Output: Located on the right side, labeled as HDMI OUT
• SDI Input: Located on the right side, labeled as SDI IN1, SDI IN2, SDI IN3, SDI IN4
• SDI Output: Located on the right side, labeled as SDI OUT
• Power Input: Located on the right side
• Configuration Ethernet: Located on the left side
• GPI/Serial Communication: Located on the left side

Operating Buttons:

• MUTE: Mute button, click to enable or disable audio play
• SINGLE: Single mode button, click to display only one picture for one signal source on the whole screen in SINGLE mode
• QUAD: Quad mode button, click to display quad split windows with different configurations
• RESET: Used to restore the factory settings. Insert a needle tool into the reset hole to trigger the reset operation

Network Control

To connect the device to your control computer via Ethernet, follow these steps:

1. Ensure that the local computer and TX401/TX402 are in the same network segment.
2. Connect TX401-B or TX402-B with your control computer using an Ethernet cable.
3. Double click the Osee.Tx401.Client application to display the management interface.
4. Select the device type as BOX or EU during the software installation process, based on your actual device.

Note : The default IP address for TX401/TX402 is 192.168.1.70.

Product Overview

• TX401-B/TX402-B is a professional quad split instrument. It supports high quality quad split displays for multiple environment with high quality display and swift switch for various display modes.
• TX401-B/TX402-B has compact and beautiful structure design, offering local control buttons and embedded web configuration functionality, and supports Ethernet loop out functionality, which is convenient for multiple TX401-B/TX402-B integration controlled by only one control computer.
• TX401-B/TX402-B is suitable in office work environment and cabinet mounting environment, it is widely used in the following fields: command and dispatch center, video conference center, broadcast master control, studio, broadcasting vehicle and so on.
  Model| Inputs| Outputs
  ---|---|---
  TX401-B| 4CH HDMI Video Input 4CH GPI Input| 1CH SDI Video Output 1CH HDMI Video Output
  TX402-B| 4CH SD/HD/3G-SDI Video Input 4CH GPI Input| 1CH SDI Video Output 1CH HDMI Video Output

Features

• Supports 4 channels of signal inputs with LED indicators and one power input indicator
• Supports four kinds of output formats: 1080P50, 1080P59.94, 1080I50, 1080I59.94
• Supports four kinds of screen display modes: four uniform size screens, one big left with three right small, one big right with three left small, one big top with three bottom small
• Supports TSL3.1/4.0, TSL5.0 protocol
• 4ch GPI interfaces, one RS-422 interface, one ETHERNET interface
• Embedded Web Server, supports web interview

TX401-B/TX402-B Features

Control Buttons and Interfaces

There are a series of control buttons, interfaces and indicators at the left side of the device, besides, a series of interfaces at the right side of the device.

Name

|

Position

| Quantity|

Description

---|---|---|---
TX401-B| TX402-B
Interfaces
HDMI Input| Right Side| 4| —| Input formats: HDMI, DVI-D, Labeled as HDMI IN1, HDMI IN2, HDMI IN3, HDMI IN4
HDMI Output| Right Side| 1| 1| Output formats: 1080P50/P59.94, 1080I50/I59.94, Labeled as HDMI OUT
SDI Input| Right Side| —| 4| Input formats: HD/SD/3G-SDI，Labeled as SDI IN1, SDI IN2, SDI IN3, SDI IN4
SDI Output| Right Side| 1| 1| Output formats: 1080P50/P59.94, 1080I50/I59.94, Labeled as SDI OUT
Power Input| Right Side| 1| 1| DC6~16V External Power(12V/1A)
Configuration Ethernet| Left Side| 1| 1| RJ45
GPI/Serial Communication| Left Side| 1| 1| RJ45, RS422 Standard, only received; TTL level
Operating Buttons
Reset| Left Side| 1| 1| Restore the factory settings
Controls| Left Side| 3| 3| Mute, Single, Quad
Indicators
Power| Left Side| 1| 1| Labeled as PWR
Input Signal| Left Side| 4| 4| Labeled as IN1, IN2, IN3, IN4

Operating Buttons

• MUTE : Mute button, click this button to enable or disable the audio play.
• SINGLE ：Single mode button, click this button to switch to display only one picture for one signal source on whole screen in SINGLE mode.
• QUAD ：Quad mode button, click this button to switch to display quad split windows, including four uniform size screens display, one big with three small screens display. The latter including one big left with three right small, one big right with three left small, one big top with three bottom small.
• RESET : used to restore the factory settings. Insert a needle tool into the reset hole to trigger the reset operation.

Network Control

Device Connect
Connect TX401-B or TX402-B with your control computer through Ethernet. Double click the Osee.Tx401.Client application to display the management interface, as shown below.

TIPS

The IP address of the local computer and TX401/TX402 must be in the same network segment. The default IP for TX401/TX402 is 192.168.1.70. You should select the device type to be “BOX” or “EU” according to your actual device during the software installation process.

• Add a TX401-B for example: click Add button in the tool bar to pop up the device connect dialog box, and input 192.168.1.70 in the IP address, click OK to connect with this device, and you will see the device in the Device List after successful connection.
• Click to select the device in the Device List, and you can configure it for general, input, display and layout settings. Besides, you can add multiple devices into the device list, import and export to share the same settings between devices.

General Setting
Click General Setting button to set the following parameters, including device IP address and its corresponding parameters, TSL address, output format, volume and mute switch.

General Setting
Firmware Version| —| —| Display FPGA/ARM version
Output Format| 1080I50| 1080I50/1080I60/

1080P50/1080P60

| Set the signal output format

Network Setting

| IP Address| 192.168.1.70| Set       the       network address of the device| Set the network address of the device
Gateway| 192.168.1.1| Set baud rate| Set the gateway of the device
Mask| 255.255.255.0| Set data bits| Set the mask of the device

RS485

| Baud Rate| 38400| Set stop bits| Set baud rate
Data bits| 8| Set parity bit| Set data bits
Stop bits| 1| Set the device name| Set stop bits
Parity bit| Even| Display    the    version number of FPGA/MCU| Set parity bit

TSL

| TSL Version| v3.1/v4.0/v5.0| v3.1| Set the version of TSL
TSL 5.0 Port| 0~65535| 8900| Set the port for the device below TSLv5.0

Volume

| Mute| OFF| ON/OFF| Enable/disable mute
Audio Level| 24| 0～31| Set volume
Reset to Default| Restore factory defaults| Click this button to restore the factory defaults.

Input Setting
Click Input Setting button to set characters for each input signals IN1～IN4: designate audio channels for each of the four audio meters, TSL3.1/4.0 address, TSL5.0 address, UMD type, UMD character, left Tally source, right Tally source.

is SIGNAL*.

Audio Meter1~4

|

Emb 1-2

| Emb 1-2

Emb 3-4

Emb 5-6

Emb 7-8

Emb 9-10

Emb 11-12

Emb 13-14

Emb 15-16

|

Set an audio channel group of two audio channels to the designated audio meter.

ID:TSL3.1/4.0| 129| —| Set the address ID for this TSL 3.1/4.0 protocol (128~255)
ID:TSL5.0| 0| —| Set the address ID for this TSL 5.0 protocol (0~65535)

UMD Type

|

Static

|

Static/Dynamic

| Set the type for UMD source as static or dynamic. If it is static, the UMD content will be the value set in UMD text; If it is dynamic, the UMD content will be the value received from the TSL
UMD Text| VIDEO_INPUT*| —| Set static UMD characters
Tally Source: L| TSL| TSL/GPI| Set the left TALLY source as GPI or TSL
Tally Source: R| TSL| TSL/GPI| Set the right TALLY source as GPI or TSL

Display Setting
Click Display Setting button to set the following display parameters: UMD and Audio Meter display position, set whether to display format, marker, border, UMD or tally lamp on the monitor window and so on.

UMD & AM Pos

| Outside Video| Outside Video Inside Video| Set the positions of UMD and audio meter relatively to the monitor frame.

Video Aspect

|

Keep     the original

| Keep the original: keep the signal source originally.

Follow window: the aspect ratio of the signal source will be consistent with the value

of monitor window.

|

Set the display area ratio of the signal source in the monitor window.

Display: Format| OFF| ON/OFF| Enable/Disable format display
Marker| OFF| ON/OFF| Enable/Disable Marker
Board| OFF| ON/OFF| Enable/Disable video frame
UMD| OFF| ON/OFF| Enable/Disable UMD
Tally Lamp Show| OFF| ON/OFF| Enable/Disable Tally light

Tally on Board

|

None

| None

Correlate Left-Tally Correlate Right-Tally

| Correlate Left-Tally or Right-Tally to border display

Tally on UMD Back

|

None

| None

Correlate Left-Tally Correlate Right-Tally

| Correlate Left-Tally or Right-Tally to UMD background display
Audio Meter: L| 4| 0/2/4| Set the audio channels displayed as left audio meter.
Audio Meter: R| 4| 0/2/4| Set the audio channels displayed as right audio meter.
UMD Character| White| White/Red/Green/Yellow| Set the color of UMD characters
Menu items| Default| Value Range| Description
---|---|---|---
Tally Color: L| Red| Red/Green/Yellow| Set the color of left Tally light
Tally Color: R| Green| Red/Green/Yellow| Set the color of right Tally light

Layout Setting
Click Layout Setting button to set the display mode to be More or Single .

More

|

1-2

| 1-2/ 3-4/1-2-3/

Four uniform size screens display; One big left with three right small; One big right with three left small; One big top with three bottom small(including another four types)

|

Switch to More display mode, you can set to display two, three or four screens.

Supported Signal Format

The supported signal format for this device is as shown in Table 2.3-1:

Input| HDMI| SDI| DVI-D| Input| HDMI| SDI| DVI-D
---|---|---|---|---|---|---|---
480/59.94i,60i| √| √|  | 1080/59.94p,60p| √| √|
576/50i| √| √|  | 640×480(60Hz)|  |  | √
720/23.98p,24p| √| √|  | 800×600(60Hz)|  |  | √
720/25p| √| √|  | 1024×768(60Hz)|  |  | √
720/29.97p,30p| √| √|  | 1280×1024(60Hz)|  |  | √
720/50p| √| √|  | 1366×768(60Hz)|  |  | √
720/59.94p,60p| √| √|  | 1440×900(60Hz)|  |  | √
1080/23.98PsF,24Ps| √| √|  | 1400×1050(60Hz)|  |  | √
1080/50i| √| √|  | 1600×1200(60Hz)|  |  | √
1080/59.94i,60i| √| √|  | 1680×1050(60Hz)|  |  | √
1080/23.98p,24p| √| √|  | 1920×1080(60Hz)|  |  | √
1080/25p| √| √|  | 1920×1200(60Hz)|  |  | √
Input| HDMI| SDI| DVI-D| Input| HDMI| SDI| DVI-D
---|---|---|---|---|---|---|---
1080/29.97p,30p| √| √|  | 2048×1152(60Hz)|  |  | √
1080/50p| √| √|  |  |  |  |

Specifications

Video Standard

| HDMI1.4| SMPTE-259M;270Mbps

VESA

| SMPTE-292M;1.485Gps
SMPTE-425M;2.97Gps
Video Output Interface| 1HDMI, 1SDI| 1HDMI, 1SDI
Video Output Format| 1080P50/P59.94、1080I50/I59.94
Dimension(WxHxD)| 128.411327.9mm| 128.411327.9mm
Power Consumption| 5.7W| 5.7W
Power Supply| DC6~16VExternal Power(12V/1A）
Control Interface| 2* RJ45 Ethernet(10/100M adaptive RJ45)
Work Temperature(°C)| 0~50| Storage Temperature(°C)| -20~60
Work Humidity(%RH)| 10~90| Storage Humidity(%RH)| 10~90

Specifications are subject to change without notice.

Address:| No.22 Building, No.68 zone, Beiqing Road, Haidian District,

Beijing, China

---|---
Post Code:| 100094
Tel:| (+86) 010-62434168
Fax:| (+86) 010-62434169
Web:| http://www.osee-dig.com/
E-mail:| sales@osee-dig.com

References

• Disney - Leadership, History, Corporate Social Responsibility
• Osee Official Website: Camera Monitor, Field Monitor and Studio Monitor

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>