Yale AC-MDC Mini Door, Window Contact Instructions

Yale AC-MDC Mini Door, Window Contact

Product Information

The Mini Door/Window Contact (AC-MDC) is a device designed to detect the opening and closing of doors or windows. It is used in conjunction with a Sync Hub for reporting and monitoring. The device is powered by a 3V CR2450 Lithium battery and features a tamper switch for unauthorized cover opening detection.

Identifying the Parts

• Rib Marks
• Battery Insulator
• Learn / Test Button – Press to transmit a learn code or enter Test Mode
• Red LED Indicator
• Tamper Switch – Triggers signal and LED when tampered
• Battery
• Mounting Holes (Knockouts)
• Tamper Compression Mark
• Magnet
• Magnet Spacer

Accessories Included

• 1 x Magnet
• 1 x Double-Sided Adhesive Magnet Spacer
• 2 x Screws
• 4 x Wall Plugs
• 1 x Double-Sided Adhesive Velcro Tape (for Mini Door/Window Contact)
• 1 x Double-Sided Adhesive Tape Pad (for Magnet)
• 2 x Magnet Mounting Screws

Product Usage Instructions

Tamper Switch

• The tamper switch protects against the unauthorized cover opening.
• When triggered, the Mini Door/Window Contact emits a signal to the Sync Hub for reporting, and the LED indicator lights up.

Battery

The Mini Door/Window Contact uses one 3V CR2450 Lithium battery as its power source. It can detect low battery and sends a low battery signal to the Sync Hub along with regular transmission. The LED indicator lights up when the device is activated under low battery status.

Changing Battery

1. Use a flat-headed screwdriver to fit into the cover opening hole on one side.
2. Push the screwdriver upwards to open the cover.
3. Repeat steps 1 and 2 on the other side of the cover.
4. Once the cover is opened, remove the old battery.
5. Press the Learn / Test button 5-6 times to fully discharge before inserting the new battery.
6. Insert the new battery with the positive side (+) facing upwards and from the top right angle as indicated in the picture.
7. To replace the cover, ensure the Tamper Compression Mark is aimed at the Tamper Switch. Fit the bottom hooks of the back cover into the bottom latches of the front cover and push it downwards until you hear a click sound.

Test Mode

The Mini Door/Window Contact can be put into Test mode for 3 minutes by pressing the Test Button once. This mode is used for testing purposes.

Product Getting Started

1. Remove the battery insulator of the Mini Door/Window Contact.
2. Put the Sync Hub into learning mode (refer to Sync Hub manual).
3. Press the Learn/Test Button on the Mini Door/Window Contact to send a signal to the Sync Hub.
4. If the Sync Hub successfully receives the signal, it should respond (e.g., emitting beeps). Refer to your Sync Hub manual to complete the learning process.
5. After the Mini Door/Window Contact is learnt-in, put the Control Panel into Walk Test mode. Hold the Mini Door/Window Contact at the desired location and press the Test button to confirm if this location is within signal range of the Control Panel.
6. When satisfied with the Mini Door/Window Contact’s location, proceed to installation.

The Mini Door/Window Contact monitors the opening/closing of specified doors and windows. The Mini Door/Window Contact is fixed to the monitored device frame with a magnet fixed to the device. When the door or window opens, the magnet moves away from the Mini Door/Window Contact, activating an internal magnetic switch causing the Mini Door/Window Contact to transmit alarm signal to the Sync hub. The device also has the capabilities of communicating signal problems along with low battery occurrences.

The Mini Door/Window Contact design consists of a front cover and a back cover. The front cover contains all electronics and the back cover provides a means for fixing the device. An enclosed PCB tamper switch provides tamper protection against unauthorised device opening.

Identifying the Parts

1. Rib Marks
2. Battery Insulator
3. Learn / Test Button
   • Press the Test button to transmit a learn code.
   • Press the Test button once to enter Test Mode for 3 minutes.
4. Red LED Indicator
5. Tamper Switch
6. Battery
7. Mounting Holes (Knockouts)
8. Tamper Compression Mark
9. Magnet
10. Magnet Spacer

Accessories Included

• 1 x Magnet
• 1 x Double-Sided Adhesive Magnet Spacer
• 2 x Screws
• 4 x Wall Plugs
• 1 x Double-Sided Adhesive Velcro Tape (for Mini Door/ Window Contact)
• 1 x Double-Sided Adhesive Tape Pad (for Magnet)
• 2 x Magnet Mounting Screws

Features

LED Indicator

In Normal Operation Mode, the LED indicator remains off except in the following situations:

• When Mini Door/Window Contact’s Tamper switch is triggered.
• When the Mini Door/Window Contact is activated with either Tamper or Low battery condition.
• When the Mini Door/Window Contact is activated and transmitting the signal under the Test mode.

Supervision

• The Mini Door/Window Contact will automatically transmit Supervisory signals periodically to the Sync Hub at random intervals of 90 to 110 minutes in Normal Operation Mode.
• If the Sync Hub has not received the signal from the Door Contact for a preset period of time, the Sync Hub will indicate that particular Mini Door/Window Contact is experiencing an out-of- signal problem.

Tamper Switch

The tamper switch is designed to protect against unauthorised cover opening. When the tamper is triggered, Mini Door/Window Contact will emit a signal to the Sync Hub for reporting, the LED will also light up.

Battery

The AC-MDC uses one 3V CR2450 Lithium battery as its power source. The Mini Door/Window Contact is also capable of detecting low battery. When the battery is low, a low battery signal will be sent to the Sync Hub along with regular transmission. The LED will light up when the Mini Door/Window Contact is activated under low battery status.

Changing Battery

You need to open the cover to insert/remove the battery:

• Step 1:  Use a flat-headed screwdriver to fit into the cover opening hole on one side as (Pic1).
• Step 2: Push the flat-headed screwdriver upwards as (Pic2).
• Step 3:  Turn to the other side and repeat Step 1 and Step 2.
• Step 4:  Once the cover is opened, you can proceed to change the battery.
  • After the battery has been removed, press the Learn / Test button 5-6 times to fully discharge before inserting the new battery.
  • NOTE: Make sure the battery mark with the positive side (+) is faced upwards when inserting the battery.
  • Make sure to insert or place the battery from the top right angle as indicated in the picture. (Pic 3)
• Step 5:  To replace the cover:
  • Make sure the Tamper Compression Mark is aimed at the Tamper Switch (Pic 4).
  • Also make sure the bottom hooks of the back cover is latched on the bottom of the front cover (back) as (Pic 5).
  • Fit the bottom hooks into the bottom latches of the front cover (back) then push it downwards as in (Pic 6) then push forward the entire back cover to close it until you hear a clip sound.

Test Mode

The Mini Door/Window Contact can be put into Test mode for 3 minutes by pressing the Test Button once.

• Under Test Mode, the LED will light up whenever the Mini Door/ Window Contact is activated.
• Each additional Test Button press will reset Test Mode time to 3 minutes.

Getting Started

• Step 1: Remove the battery insulator of the Mini Door/Window Contact.
• Step 2: Put the Sync hub into learning mode, refer to Sync hub manual for detail.
• Step 3: Press the Learn/Test Button on Mini Door/Window Contact to send signal to the Sync hub.
• Step 4: If the Sync hub successfully receives the signal, the Sync hub should respond (e.g. emitting beeps).
  • Refer to your Sync hub manual to complete the learning process.
• Step 5: After the Mini Door/Window Contact is learnt-in, put the Control Panel into “Walk Test” mode, hold the Mini Door/Window Contact at the desired location, and press the Test button to confirm if this location is within signal range of the Control Panel.
• Step 6: When you are satisfied with the Mini Door/Window Contact at the chosen location, proceed to installation.

Installation

Mounting Methods

• Mount the Mini Door/Window Contact on the fixed frame of door/ window using Velcro tape Mounting or Screw Mounting.
• Mount the magnet on the mobile object (door/window) using Screw Mounting or Adhesive Mounting.
• Align the magnet according the rib mark on Mini Door/Window Contact. Where required, use the Magnet Spacer to better align the magnet to the rib marks.

NOTE: The magnet should be no more than 15mm from the detector when the door is closed.

Mounting Methods for the Mini Door/Window Contact Screw Mounting

• The back cover has two Mounting Holes (knockouts), where the plastic is thinner for mounting purpose.

To Mount the Mini Door/Window Contact:

1. Remove the cover.
2. Break through the knockout on the back cover.
3. Using the holes as a template, drill both holes.
4. Insert wall plugs if fixing into plaster or brick.
5. Screw the back cover into the wall plug using a Philips screwdriver.
6. Attach the front cover to the back cover.

Velcro Tape Mounting:

The Mini Door/Window Contact can be wall mounted using Velcro tape provided.

1. Clean the wall mounting location and back of the Mini Door/Window Contact with degreaser. Do not mount on wall with cracking paint or rough surface.
2. The Velcro tape can be separated to Hook and Loop side. (Pic 7)
3. Remove the protective cover of the Hook side and attach to the back of the Mini Door/Window Contact. Press firmly for 30 seconds to ensure good contact. (Pic 8.)
4. Remove the protective cover of the Loop side and apply to desired mounting location as in (Pic 9.) Press firmly for 30 seconds to ensure good contact.
5. Apply the Mini Door/Window Contact on the Loop side Velcro taped on the wall (Pic 10 & 11.)

Mounting Methods for the Magnet

Screw Mounting

The back cover of the magnet has two Mounting Holes for mounting purpose.

To Mount the Magnet

1. Open the back cover by using a flat-headed screwdriver to fit into the caved in area and push upwards.
2. Using the holes as a template, drill both holes.
3. Screw the back cover into the door/window using a Philips screwdriver. Where required, use the Magnet Spacer to better align the magnet to the rib marks.
4. Attach the front cover to the back cover. You will hear a Click sound when the front cover is stabilised onto the back cover.

Adhesive Mounting

The Magnet can also be mounted using the double-sided adhesive tape pad or the double-sided adhesive Magnet Spacer.

1. Clean the mounting location and back of the Magnet with a suitable degreaser.
2. Remove the protective covering from one side of the double-sided adhesive pad or the double-sided adhesive Magnet Spacer. Apply to the back of the Magnet and press firmly for 30 seconds to ensure good contact.
3. Remove the other cover and firmly press the Magnet onto the desired location for 30 seconds.

NOTE: Please do not re-apply the double-sided adhesive tape pad or the double-sided adhesive Magnet Spacer. They cannot be re-used.

More Information

• www.yalehome.co.uk
• Security & Risk Communications Limited, Parkway Business Centre, Ballymount, Dublin, Ireland, 24

ASSA ABLOY Opening Solutions UK & Ireland

• School Street, Willenhall West Midlands, WV13 3PW UK Version 1A

References

• YaleHome | Protect Your Home The Smarter Way With Yale

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>