Husqvarna 345BT Cordless Bubble Blower User Manual

: June 9, 2024
: Husqvarna

Table of Contents

Husqvarna 345BT Cordless Bubble Blower
Introduction
Product Overview
Symbols on the product
Product liability
Assembly
Operation
Transportation and storage
Troubleshooting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Husqvarna 345BT Cordless Bubble Blower

Introduction

Product Description

This product is a backpack blower with a fuel engine. We have a policy of continuous product development and therefore reserve the right to modify the design and appearance of products without prior notice.

Intended use

Use the product to blow leaves and other unwanted material from areas such as lawns, pathways and asphalt roads.

Product Overview

Throttle control lever
Frame
Harness
Engine cover
Fan cover
Air intake screen
Air filter
Starter rope handle
Fuel tank
Waist belt
Spark plug
Vibration damping system
Choke control
Control handle
Stop switch with throttle control
Throttle trigger
Pipe angle
Clamp
Flexible hose
Control pipe
Cable clamp
Intermediate pipe
Blower nozzle
Operator’s manual
Combination wrench
Air purge bulb
High speed nozzle
Idle adjustment screw
Fan
Foot plate

Symbols on the product

WARNING! This product can be dangerous and cause serious injury or death to the operator or others. Be careful and use the product correctly.
(Read the operator’s manual carefully and make sure that you understand the instructions before use.
Use approved hearing protection and approved eye protection. If the environment contains dust, use a breathing mask.
Use approved protective gloves during operation and maintenance. Use protective boots or shoes with non-slipsoles. Use clothing of strong fabric and offull length.
Make sure that long hair is put above your shoulders.
Do not wear jewelry or loose clothing during operation.
Mixture of gasoline and two-stroke oil.
Air purge bulb.
Keep all body parts away from hot surfaces.
Do not go near the impeller as it turns. Choke, open position.
Choke, closed position.
Idle adjustment screw.
This product complies with applicable EC Directives.
This product conforms to the applicable UK regulations.
Noise emissions to the environment according to European Directive 2000/14/EC and New South Wales legislation “Protection of the Environment Operations
(Noise Control) Regulation2017”. Noise emission data can be found on the machine label and in the Technical data chapter.
Look out for thrown objects. Thrown objects can cause serious injury. Use personal protective equipment.
( Keep a safety distance at a minimum of 15 m to persons or animals.
The rating plate or the laser printing shows the serial number. yyyy is the production year and ww is the production week.

Product liability

As referred to in the product liability laws, we are not liable for damages that our product causes if:

the product is incorrectly repaired.
the product is repaired with parts that are not from the manufacturer or not approved by the manufacturer.
the product has an accessory that is not from the manufacturer or not approved by the manufacturer.
the product is not repaired at an approved service center or by an approved authority

Safety definitions
The definitions below give the level of severity for each signal word

General safety instructions.

Do not do changes to the product without approval from the manufacturer and always use original accessories.
Modifications and/or accessories that are not approved can result in serious injury or the death of the operator or others.
Do not use a damaged product. Do the safety checks and maintenance given in this operator’s manual.
All other maintenance must be done by approved servicing personnel.
All servicing and repair operations must be done by approved servicing personnel.
If a part of the product is defective, speak to your servicing dealer.

Vibration safety
This product is for occasional operation only. Continuous or regular operation of the product can cause “white finger” or equivalent medical problems from vibrations. Examine the condition of your hands and fingers if you operate the product continuously or regularly. If your hands or fingers have discoloration, have pain, tingle, or are numb, stop work and speak to a physician immediately.

Safety instructions for operation

This product can be dangerous and cause serious injury or death to the operator or others.
Be careful and use the product correctly.
Do an inspection of the product before use. Refer to Maintenance on page 12.
Do not operate the product when you are tired, ill or under the influence of alcohol or other drugs that can decrease your vision, judgment or coordination.
Install all covers and guards before use. To prevent electrical shock, make sure that the spark plug cap and ignition cable are not damaged.
Do not touch the spark plug or ignition cable when the engine is on.
Keep a safety distance at a minimum of 15 m to persons or animals.
If persons, children or animals come nearer than 15 m, stop the product.
Point the product away from persons, animals, open windows and other objects.
Do not let children operate the product. Make sure that all operators read and understand the contents of this operator’s manual.
Keep hands or other objects away from the blower housing during operation.
Rotating parts can cause serious injury.
Do not use the product if the air intake screen is not installed. Always make sure that the air intake screen is installed and not damaged before use.
If an emergency occurs, release the waist belt and chest belt of the harness and let the product fall.
Obey national regulations and directives.
Keep all body parts away from hot surfaces.
Too much vibration can cause damage to the circulation or the nervous system.
Speak to your physician if you have symptoms, for example numbness, loss of feeling, tingling, pricking, pain, loss of strength or changes in skin color in your fingers, hands or wrists.
Look out for thrown objects. Thrown objects can cause serious injury.
Do not use the product in bad weather, for example fog, rain, strong winds and too cold environments.
To do work in bad weather can cause tiredness and dangerous conditions.
Make sure that you can move and keep a stable position.
Do a check of the work area for possible obstacles, for example rocks.
Be careful if you operate the product on a slope.
Do not put the product on the ground with the engine on.
Do not operate the product from high positions, for example on a ladder.
Make sure that you can always be heard if an accident occurs.
Make sure that the exhaust fume outlet is not blocked.
To prevent damage to the product, keep obstacles at a minimum distance of 50 cm from the exhaust fume outlet.
Do not start the product indoors, in bad airflow or near flammable material.
The engine exhaust fumes contain carbon monoxide, which can cause carbon monoxide poisoning.
The engine exhaust fumes are hot and can contain sparks which can start a fire.

Personal protective equipment

Use approved personal protective equipment when you use the product.
Personal protective equipment cannot fully prevent injury but it can decrease the degree of injury.
Speak to your dealer for more information.
Use approved hearing protection. Long-term exposure to noise can result in permanent hearing damage.
Use approved eye protection. If you use a visor, you must also use approved protective goggles.
Approved protective goggles must agree with the ANSI Z87.1 standard in the USA or EN 166 in EU countries.
Use protective gloves during operation and maintenance.
Use protective boots or shoes with non-slip soles.
Use clothing of strong fabric and of full length.
Do not use jewelry or open shoes. To decrease the risk on injury, your clothing must be close-fitting but not limit your movements.
Put your hair above your shoulders to prevent that your hair enters rotating parts or catches on branches.
Use breathing protection when there is a risk of dust.
Keep first aid equipment near

Safety devices on the product

Do not use a product with defective safety devices.
Do a check of the safety devices regularly. Refer to Maintenance on page 12.
If the safety devices are defective, speak to your Husqvarna servicing dealer
Regularly do a visual check of the muffler. The muffler keeps noise levels to a minimum and sends exhaust fumes away from the operator. Refer to To examine and clean the cooling system

To do a check of the vibration damping system

Make sure that there are no cracks or deformation on the vibration damping units.
Make sure that the vibration damping units are correctly attached to the engine unit and handle unit.
Refer to Product overview on page 6 for information about where the vibration damping system is on your product.

To do a check of the start/stop switch

Use the start/stop switch to stop the engine.
Make sure that the engine stops fully.
To see where the start/stop switch is on your product, refer to Product overview on page 6

Harness safety
Always use the harness when you operate the product. If you do not use the harness, you cannot operate the product safely. This can result in injury to you or other persons. Make sure that the waist belt and chest strap are attached and correctly adjusted. There is a risk that an open belt can go into the fan of the product

Fuel safety

Do not mix or add the fuel indoors or near a heat source.
Do not start the product if there is fuel or oil on the product or on your body.
Do not start the product if the engine has a fuel leak.
Examine the engine for fuel leaks regularly.
Always be careful with fuel. Fuel is flammable and the fuel fumes are explosive and can cause serious injury or death.
Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
Do not smoke near the fuel or the engine.
Do not put the product or a fuel container near warm objects, an open flame, a spark or a pilot light.
Always use approved containers for storage and transportation of fuel.

Safety instructions for maintenance

Stop the engine, remove the spark plug and let the engine become cool before maintenance and assembly.
A blocked spark arrestor screen causes the engine to become too hot which causes damage to the engine.
If the spark arrestor screen is frequently blocked, it can be a sign that performance of the catalytic converter is decreased. Speak to your servicing dealer to examine the muffler

Assembly

Introduction

Attach the flexible hose (A) to the pipe angle and the control pipe (B) with the clamps (C) and (D).
Attach the handle holder (E) to the control pipe. Align the handle holder with the flange on the control pipe.
Adjust the position of the control handle to a safe and correct work position. Tighten the knob.
Attach the cable to the flexible hose with the cable clamp.
Attach the intermediate pipe to the control pipe.
Attach the blower nozzle to the intermediate pipe.

Operation

Premixed fuel
Use Husqvarna premixed alkylate fuel for best performance and extension of the engine life. This fuel contains less harmful chemicals compared to regular fuel, which decreases harmful exhaust fumes. The quantity of remains after combustion is lower with this fuel, which keeps the components of the engine more clean.

To mix fuel

Gasoline

Use good quality unleaded gasoline with a maximum of 10% ethanol contents.

Two-stroke oil

For best results and performance use Husqvarna two-stroke oil.
If Husqvarna two-stroke oil is not available, use a two-stroke oil of good quality for air-cooled engines.
Speak to your servicing dealer to select the correct oil.

To mix gasoline and two-stroke oil

Fill half the quantity of gasoline in a clean container for fuel.
Add the full quantity of oil.
Shake the fuel mixture.
Add the remaining quantity of gasoline to the container.
Carefully shake the fuel mixture

To start a cold engine

If the engine is cold, put the choke control (A) to the closed choke position. Refer to Symbols on the product on page 6.
Push the air purge bulb (B) again and again for a minimum of 10 times and fuel starts to fill the air purge bulb. It is not necessary to fill the air purge bulb fully.
Put the throttle control in the fast idle position. Align the guide marks on the throttle control lever and the control handle.
Put the product on a flat surface on the ground.
Hold the product with the left hand and put your foot on the foot plate.
Pull the starter rope handle slowly with the right hand until resistance occurs.

To start a warm engine

If the ambient temperature is below 32°C / 90°F, use the same starting procedure as To start a cold engine on page 11 but do not put the choke control in the closed choke position.
If the ambient temperature is above 32°C / 90°F, use the same starting procedure as To start a cold engine on page 11.

To use the throttle trigger

To increase the blower speed during operation, push the throttle trigger until you get the correct speed.
To decrease the blower speed during operation, release the throttle trigger until you get the correct speed.

To start the engine when the fuel is too hot

Put the product in a cool area away from open sunlight.
Let the product cool down for 20 minutes at minimum.
Press the air purge bulb again and again for 10-15 seconds.
Obey the procedure to start a cold engine. Refer to
To start a cold engine on page 11.

To operate the product

Operate the product at usual work hours. Obey local regulations.
Decrease the pieces of equipment and select the correct speed for your task. Use the throttle at lowest position possible to prevent more noise and dust than necessary.
Keep the blower nozzle near the ground.

To stop the product

Do not stop the product at full speed.
Push the stop switch.

To adjust the harness

Put on the harness of the product.
Put the waist belt around your waist and connect the belt buckle for the waist strap.
Tighten the waist belt strap.
Connect the belt buckle for the chest strap.
Adjust the position of the chest strap.
Tighten the chest strap.
Tighten the shoulder straps until the product is tight against your body.
Tighten the load lifter straps.

Maintenance schedule

To adjust the idle speed

Make sure that the air filter is clean and that the air filter cover is attached.
Adjust the idle speed with the idle speed screw. To see where the idle speed screw is on your product, refer to Product overview on page 6.

To do a check of the spark plug

Stop the engine and let the product become cool.
Clean the spark plug if it is dirty.
Make sure that the electrode gap is correct. Refer to
Technical data on page 16.
Replace the spark plug monthly or more frequently if it is necessary

To do maintenance on the muffler

Clean the spark arrestor screen on the muffler. Use a wire brush. (
Let a servicing dealer replace or do service on the muffler and the spark arrestor screen after 50 hours of operation.

Transportation and storage

Empty the fuel tank before transportation or longterm storage. Push the air purge bulb to make sure that all fuel is removed. Discard the fuel at an applicable disposal location.
Make sure that the product is clean and that a full servicing is done before long-term storage.
Remove the spark plug and put approximately 15 ml of two-stroke oil into the cylinder. Turn the product 3 times and install the spark plug again.
Attach the product safely to the vehicle during transportation.
Keep the product in a dry, cool and clean space with good airflow. Keep the product away from children

Technical data

EC Declaration of Conformity

We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN, declare under our sole responsibility that the represented product complies fully with the following EU directives and regulations

UK declaration of conformity

We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN, declare under our sole responsibility that the product