YUNEEC E45S 45MP Full Frame Survey Camera User Guide
- June 12, 2024
- YUNEEC
Table of Contents
YUNEEC E45S 45MP Full Frame Survey Camera User Guide
Introduction and Overview
-
LED Status Indicator
-
Camera Lens
-
Micro SD Card Port
-
Gimbal
Specifications
General
Product Name: 3-Axis Gimbal
Camera Model Name: E45S
Weight: 440g
Dimensions: 138x 133x113mm
Environmental
Operating Temperature Range: -10°C to 50°C
Camera
Sensor: CMOS FF 36x24mm
Effective Pixels: 45MP
Lens: 35mm f/5.6 DFOV: 63°
Video Formats: MP4
Video Resolutions: 3840×2160 30fps
Photo Formats: JPEG
Photo Resolutions: 8192×5460
Operation Mode: Capture, Record
Exposure Mode: Semi–auto Exposure
Shutter Speed: 1/600–1/1200s
ISO: 100 – 1600
White Balance: Auto
Gimbal
Number of Axis: 3
Control Angle Accuracy: ± 0.02°
Maximum Control Range: Tilt: -90° to 0°, Pan:165°
Maximum Control Speed: Tilt: 30°/s, Pan: 120°/s
Gimbal Installation
Assembling
Step 1
Find the Unlocked Mark etched on the Gimbal Yaw Motor and align the Mark Line
with the front of the damping plate.
Step 2
Insert the Gimbal Yaw Motor into the damping plate and rotate it
counterclockwise until the Mark Line of the Locked Mark aligns with the front
of the damping plate to secure the gimbal.
Step 3
Remove the lens protector and open the Micro SD Card Slot Cover to insert the
SD card.
Disassembling
Step 1
Hold the gimbal release button and rotate the Gimbal Yaw Motor clockwise until
the Mark Line of the Unlocked Mark aligns with the front of the damping plate.
Step 2
Pull the gimbal out from the damping plate.
Notice:
The X-connector series gimbal does not need a separate binding. If a re-
binding is required, please refer to the corresponding section in the Drone
Quick Start Guide.
Danger:
Do not hot-plug the device while powered on, as it might cause electrical
damage.
NOTICE
- Ensure that the gimbals firmware has been updated to the latest version.
- For the latest product information, please check our official website: www.yuneec.com
WARNING
- Do not try to repair the E45S.
- Do not operate the E45S in the rain or in environments with high humidity. Wait until the initialization process is complete before touching or removing the camera.
- The following language terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
a) If procedures are not correctly followed, there is a risk of device, property damage and personal injury.
b) Read the entire instruction manual to become familiar with the product‘s features before operating.
Do not use incompatible components or alter this product in any way outside o the instructions provided by Yuneec.
Failure to use this product in the intended manner as described in the instruction manual can result in damage to the product or property and/or cause serious injury.
Disclaimer
Yuneec shall not be held liable for any damage, injury or for the use of the product in violation of legal regulations, especially in the following circumstances:
-
Damage and/or injury as well as breach of legal rules resulting from a failure to comply with the operating instructions or the instructions at www.yuneec.com, product information, user manual and other legally binding information.
-
Damage and/or injury, as well as violation of legal regulations, brought about by the influence of alcohol, drugs, medication or other narcotics, which may impact the user‘s concentration.
The same applies to illnesses affecting the user‘s concentration (dizziness, tiredness, nausea etc.) or other factors compromising mental and physical capabilities. -
Intentionally caused damage, injury or violation of legal regulations.
Any request for compensation caused by an accident resulting from the use of the product. -
Damage and/or injury as well as violation of legal regulations caused by use of the product in a no-fly zone, e.g. next to an airfield, above a motorway or a natural conservation area.
-
Malfunction of the product caused by retrofitting or replacement with components which did not come from Yuneec.
-
Damage and/or injury caused by the use of replica parts (non-original parts).
-
Damage and/or injury as well as violation of legal regulations caused by incorrect operation or misjudgment.
-
Damage and/or injury caused by damaged spare parts or not using original Yuneec spare parts.
-
Damage and/or injury as well as violation of legal regulations caused by ignoring the low voltage battery warning.
-
Damage and/or injury as well as violation of legal regulations caused by operating the model in a magnetic field (e.g. high voltage lines, electricity/ transformer stations, radio towers, mobile phone masts etc.), a strong wireless signal environment, no-fly zones, poor visibility and in the event of vision impairments or other impacts on the pilot which are left unchecked etc.)
-
Damage and/or injury brought about through a violation of the legal regulations for operating the model, in unsuitable weather conditions, e.g. rain, wind, snow, hail, storms, hurricanes etc.
-
Damage and/or injury as well as violation of legal regulations caused by force majeure, e.g. collision, fire, explosion, flooding, tsunami, landslide, avalanche, earthquake or other forces of nature.
-
Damage and/or injury as well as violation of legal regulations caused by the illegal or immoral use of the model, e.g. capturing videos or recording data which infringes upon/harms the privacy of other people.
-
Damage and/or injury as well as violation of legal regulations caused by incorrect use of the batteries, protection systems, chargers or aircraft.
-
Consequential damage caused by the incorrect operation of any kind of system components and accessory parts, especially memory cards, whereby an image or video material from the camera can become defect.
-
Any non-compliance with legal obligations, personal injury, material damage and environmental damage caused by use and a failure to comply with the local laws and regulations.
-
Damage and/or injury as well as violation of legal regulations caused by hazardous use without sufficient practical experience.
-
Damage and/or injury as well as violation of legal regulations caused by flying in legally defined no-fly zones.
-
Further losses which do not fall within the scope of use are defined by Yuneec as improper.
-
This product is designed for both professional use and personal, private use.
The national and international laws and regulations in force at the time of taking off must be adhered to.
FCC Statement
This equipment has been tested and found to comply with the limits of Part 15 of the FCC rules. These limits are designed to protect reasonably against harmful interference in a residential environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in any situation.
Harmful interference to radio or television reception can be determined by turning the equipment off and on. This situation, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
EU Compliance Statement
Yuneec declares that this device complies with the essential requirements and
other relevant provisions of the RED Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the
following internet address www.yuneec.com.
Please visit the address above and enter the corresponding product page.
This content is subject to change. Download the latest version from
www.yuneec.com
If you have any questions or inquiries about this document,
please contact us by starting a conversation on
www.yuneec.com
ATL Drone – Global Headquarters
Rütistrasse 18, 8952 Schlieren, Switzerland