EVELO Atlas and Omega Secondary Battery Kit Installation Guide
- June 12, 2024
- EVELO
Table of Contents
EVELO Atlas and Omega Secondary Battery Kit
Product Information
The Omega and Atlas models from EVELO are bicycles that come with a rear rack and a secondary battery. This user manual provides instructions on how to install the rear rack and battery on these models. It is important to follow these instructions carefully to avoid any damage to the battery or bicycle.
- Step 1: Removing the Light
- To begin the installation, open the seatpost quick release and unscrew it to remove the light. Unplug the connector, then reassemble and tighten the seatpost quick release.
- Step 2: Removing the Mounting Bolts
- Using an allen wrench, remove the four rack mounting bolts from the frame and discard them. New, longer bolts will be included with the rack.
- Step 3: Holding the Rack in Place
- Remove the battery from the rack and hold the rack in place on the bike. It is crucial to remove the battery from the rack prior to installation to avoid any damage to the battery or bicycle.
- Step 4: Installing Lower Mounting Bolts
- Using an allen wrench, install the lower mounting bolts. Use the longer bolts provided with the rack package as the ones that came with the bike are too short to securely hold the rack.
- Step 5: Installing Upper Mounting Bolts
- Using an allen wrench, install the upper mounting bolts. Use the longer bolts provided with the rack package as the ones that came with the bike are too short to securely hold the rack.
- Step 6: Connecting the Taillight
- Connect the new taillight to the connector that was unplugged earlier. Line up the arrows on each half of the connector and push them together. Make sure the rear battery is removed and the bicycle is powered off before connecting the plugs.
- Step 7: Plugging in the Battery
- Open the cover and plug the battery into the frame port. Ensure that the plug orientation is correct as it will only go in one way. Again, make sure the rear battery is removed and the bicycle is powered off before connecting the plugs.
- Step 8: Final Check
- Your connections should now be complete. Take a look to ensure everything is properly connected and secure.
Product Usage Instructions
To charge the bike with both batteries installed, connect only the charger
that came with the bike to either battery, and both batteries will be charged
simultaneously. Do not plug a charger into both the main battery and the
secondary battery at the same time when both are installed on the bike.
If you have any questions or need further assistance, please contact EVELO at
877-991-7272 or email
contact@evelo.com. You can also visit their
website at EVELO.COM for more information.
This guide shows how to install the rear rack and secondary battery on your new EVELO bicycle. This applies to Atlas and Omega models
INSTALLATION
-
Step 1: Open the seatpost quick release, then unscrew it to remove the light. Unplug the connector, then reassemble and tighten the seatpost quick release.
-
Step 2: Using an allen wrench, remove the four rack mounting bolts from the frame and discard. New, longer bolts will be included with the rack.
-
Step 3: Remove the battery from the rack and hold the rack in place on the bike.
REMOVING THE BATTERY FROM THE RACK PRIOR TO INSTALLATION IS CRUCIAL TO AVOID DAMAGE TO BATTERY AND/OR BICYCLE. -
Step 4: Using an allen wrench, install the lower mounting bolts. Use the longer bolts from the rack package; the bolts that came on the bike are too short to hold the rack securely.
-
Step 5: Using an allen wrench, install the upper mounting bolts. Use the longer bolts from the rack package; the bolts that came on the bike are too short to hold the rack securely
-
Step 6: Connect the new taillight to the connector you unplugged earlier. Line up the arrows on each half of the connector and push them together.
MAKE SURE REAR BATTERY IS REMOVED AND BICYCLE IS POWERED OFF BEFORE CONNECTING PLUGS -
Step 7: Open the cover and plug the battery into the frame port. It will only go in one way, so be aware of the plug orientation.
MAKE SURE REAR BATTERY IS REMOVED AND BICYCLE IS POWERED OFF BEFORE CONNECTING PLUGS -
Step 8: Your connections should now look like this. Go ride your bike!
Charging
To charge the bike with both batteries installed, connect only the charger that came with the bike to either battery and both will be charged. DO NOT PLUG A CHARGER INTO THE MAIN BATTERY AND THE SECONDARY BATTERY AT THE SAME TIME WHEN BOTH ARE INSTALLED ON THE BIKE.
Questions? Get In Touch:
EVELO.COM
First Edition
877-991-7272
contact@evelo.com
EVELO Omega and Atlas Battery Rack Installation
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>