LIVE AQUA Prime Pro Series High Color Rendering and Wireless Controllable RGB Plus UV LED Aquarium Light Instruction Manual

LIVE AQUA Prime Pro Series High Color Rendering and Wireless Controllable RGB Plus UV LED Aquarium Light

SAFETY INSTRUCTIONS

General

1. Do not use this product in any manner not specified by the manufacturer.
2. Do not install substitute parts or perform any unauthorized modification to the product.
3. Do not attempt to disassemble the product.
4. Return the product to a MaxLite Engineering Sales and Service Office for service and repair.
5. MaxLite Engineering will not be responsible for damage to the product, nor to repair the
   product, resulting from such causes as an improper installation, or use, or modification of the product, or connecting to an incompatible power supply, or the product is serviced by another company.

Power Supply

1. Only use original power supply of the product. Use of any other power supply may cause damage to the product, this product cannot be use on dimmer.
2. The power supply is provided with a grounding-type power cord set. The ground pin of the cord set plug must be firmly connected to the electrical ground (safety ground) terminal at the power outlet.
3. Do not damage the power cable insulation. Damaged insulation can result in a short circuit, electrical shock and/or fire.
4. Do not forcefully bend, twist or pull the power cable. This can cause damage to the power cable and may result in fire or electrical shock.
5. Immediately stop using this product if power cable is damaged.
6. The power supply is conventional cooled. Do not place any heat insulating materials over the power supply, heat will build up and result in fire or damage of the power supply.

Installation & Operation

1. This product is a pendant type light fixture for an aquarium. The product is intended lo be hung from ceiling or the light stand (optional) of this product.
2. Consult a contractor before hanging the product with hook from ceiling. Ensure both the hook and ceiling are strong enough for the weight of the product (At least 5 kg).
3. This product is for indoor use only.
4. Do not operate this product in the presence of flammable liquids or vapors.
5. The product is conventional cooled and is designed to operate at room temperature between a and 35’C.
6. The product is water proof IPX4 or higher designed.

FEATURE

Life Aqua “Prime” series is a high color rendering and Wi-Fi wireless controllable RGB LED Aquarium Lighting, specific designed for natural plants aquarium. Integrating our professional and unique technologies the RGB LED output are optimized, aquatic plants grow naturally and healthily. Plants original colors are faithfully and perfectly presented.
Plus the wireless control technology, aquatic plants can be retained in the natural environment by simulating the cycle of sunlight (such as sunrise and sunset). Users can create the unique schedule and timer setting to present the unique aquarium. Life Aqua “Prime” series leads nature planted aquarium into future.

SPECIFICATION

Prime Pro

– 2000 Lx
Number of LEDs| 30 (RGB) + 2 (UV)| 40 (RGB) + 2 (UV)| 60 (RGB) + 3 (UV)| 80 (RGB) + 4 (UV)

Prime Pro EX

illuminance
(4 level) -900mm| 1800 Lx| 2400 Lx| 3600 Lx| 4500 Lx
Number of LEDs| 72 (RGB) + 1 (Ripple)| 96 (RGB) + 1 (Ripple)| 144 (RGB) + 1 (Ripple)| 196 (RGB) + 1 (Ripple)

Others Specification

PRODUCT DETAIL

Ensure all parts are included before installation and operation. If any parts are missing or damaged, please contact Maxlite Engineering Sales and Service Office.

INSTALLATION

Type: Hanging

1. Assemble the hanging set by passing through the hole on the hanging holder, and then screw the hanging set to the lighting unit. (Fig. 1)
   

2. Make a loop to circulate the stand (optional) with each of the hanging set and the wire clamps. (Fig. 2)

3. Adjust the distance between two hanging sets to keep the lighting unit on the horizon. (Recommend to keep at least 300 mm distance from the edge of the tank.)
   

Type: Fixed Stand

1. Distinguish the left and right direction of the acrylic stand, and then screw it to the lighting unit. (Fig. 3)
2. Place the lighting unit on the tank. (Be aware the length of the tank should be same as the lighting unit.)
   

Type: Adjustable Stand

1. Distinguish the left and right adjustable stand, and then pass the holding stick through the outermost hole ont the lighting unit. (Fig. 4)
2. Align the lighting unit with the tank by adjusting the length of the adjustable stick, and then place it on the edge of the tank.
   

OPERATION

Power on

1. Connect the power supply to AC mains.
2. Switch on the lighting unit by pressing the power push button. (Power LED blinking until the light up process finish.)
   *Lighting unit will turn on with the last RGB Lighting level, including the sudden power failure and smart plug operation.
3. Press the power push button for 3 seconds to reset the memory. ( Release to complete when the Power LED blinking.)

RGB lighting level (Manual)

1. Press the RGB push button once to adjust the level.
   *4 built-in level can be adjusted.

Wireless Control (Pairing)

1. Download the APP – MaxLiving. (Fig. 6 )
   

2. Sign-in / Sign-up MaxLiving to control and monitor the smart housing devices.

3. Press the “+” Button on the top right hand corner to adding the devices. (Fig. 7)

4. Search “Life Aqua – Prime Pro / Prime Pro EX” in the “Aquarium” class.b

5. Select the device and follow the steps showing on the screen.
   a. Press the WiFi push button on the lighting unit for 5 seconds to activate the pairing mode. (WiFi LED fast blinking (- 2times/s) can be observed.) Press “Confirm indicator rapidly blick” to continue. (Fig. 9)
   b. Connect the smart phone to the WiFi network (802.11b/g/n – 2.4GHz).
   c. After that, the pairing will start automatically after pressing the “Confirm” button.
   d. The WiFi LED stops blinking to indicate that the pairing is complete.
   e. Device – “Prime Pro / EX” (e.g.) will show on the screen if the pairing success.

*Pairing detail can be find in “loT Handbook” on www.life-aqua.com

Wireless Control (Controlling)

After the pairing, user can control and monitor the lighting device on the APP

APP Function:
Power Button

1. To switch on/off the lighting unit.

Color Button

1. 1To adjust the color ratio.

Scene Button:

1. To provide different RGB ratios and brightness to simulate different sunlight conditions.
2. Also provide 4 sets of custom scene to fulfill users need.

Schedule

1. Set and upload the schedule to the cloud platform, to control the operation of the lighting unit automatically.
2. Users can upload any scene (including custom scenes) and set the time for different need. (For example, automatic on / off of daily lighting, sunrise / sunset simulation)

• Operation detail can find in “Life Aqua – loT Handbook” on www.life-aqua.com

MAINTENANCE

(Should be only handled by MaxLite authorized Service team)

• Avoid dust accumulation cover the lighting unit. Use a blower to clean to dust if necessary.

• Clean surface of lighting unit/diffuser with a damp cloth. Do not use detergent or solvent.

• Store the lighting unit in a dry place without high temperature heat source when the lighting unit
  is not in used.

• Power off the lighting unit, wait until it is completely cool down and disconnect the extension power cable before maintenance.

• Do not attempt to disassemble the product for maintenance.

References

• Life Aqua - Aquarium Light Revolution

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>