TROTEC BW10 Measuring Device Instruction Manual

TROTEC BW10 Measuring Device

Product Information

• Product Name: BW10 pH Measuring Device
• Model: TRT-BA-BW10-TC220613TTRT06-004-EN
• Intended Use: The BW10 pH measuring device is designed for determining the pH value and temperature of liquids in aquaria, ponds, swimming pools, and food.
• Manufacturer: Trotec
• Website: https://hub.trotec.com/?id=39360

Product Usage Instructions

1. Read the operating manual carefully before using the device.
2. Store the manual in the immediate vicinity of the device or its site of use.
3. Ensure that the device is used only for its intended purpose.
4. Use only approved accessories and spare parts provided by Trotec.
5. Do not use the device in potentially explosive atmospheres or for measurements at live parts.
6. Avoid using the device under laboratory conditions.
7. Do not modify, alter, or make structural changes to the device without authorization.
8. Avoid using corrosive liquids such as bases and acids with the device.
9. Protective measures:
   • Do not immerse the device and accessories in water to prevent short circuits.
   • Work on electrical components should only be carried out by authorized specialists.
   • Handle strong acids or bases with care and wear suitable protective equipment, including eye protection, protective clothing, protective gloves, and safety boots.

Symbols

• Warning of electrical voltage
  This symbol indicates dangers to the life and health of persons due to electrical voltage.

• Warning
  This signal word indicates a hazard with an average risk level that, if not avoided, can result in serious injury or death.

• Caution
  This signal word indicates a hazard with a low-risk level which, if not avoided, can result in minor or moderate injury.

• Note
  This signal word indicates important information (e.g. material damage) but does not indicate hazards.

• Info
  Information marked with this symbol helps you to carry out your tasks quickly and safely.

• Follow the manual
  Information marked with this symbol indicates that the operating manual must be observed.

• Wear protective equipment
  Information marked with these symbols indicates that you should wear your personal protective equipment.

You can download the current version of the operating manual and the EU declaration of conformity via the following link:

https://hub.trotec.com/?id=39360

Safety

Read this manual carefully before starting or using the device. Always store the manual in the immediate vicinity of the device or its site of use.

Warning
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.

• Do not use the device in potentially explosive rooms or areas and do not install it there.
• Do not use the device in an aggressive atmosphere.
• This device is not a toy. Keep away from children and animals. Do not leave the device unattended during operation.
• Never immerse the entire device in a liquid. Only the measuring probe is intended to be immersed.
• Protect the device from permanent direct sunlight.
• Do not remove any safety signs, stickers or labels from the device. Keep all safety signs, stickers, and labels in legible condition.
• Do not open the device.
• Never charge batteries that cannot be recharged.
• Different types of batteries and new and used batteries must not be used together.
• Insert the batteries into the battery compartment according to the correct polarity.
• Remove discharged batteries from the device. Batteries contain materials hazardous to the environment. Dispose of the batteries according to the national regulations.
• Remove the batteries from the device if you will not be using the device for a longer period of time.
• Never short-circuit the supply terminal in the battery compartment!
• Do not swallow batteries! If a battery is swallowed, it can cause severe internal burns within 2 hours! These burns can lead to death!
• If you think batteries might have been swallowed or otherwise entered the body, seek medical attention immediately!
• Keep new and used batteries and an open battery compartment away from children.
• Only use the device, if sufficient safety precautions were taken at the surveyed location (e.g. when performing measurements along public roads, on building sites etc.). Otherwise do not use the device.
• Observe the storage and operating conditions (see Technical data).
• Check accessories and connection parts for possible damage prior to every use of the device. Do not use any defective devices or device parts.

Intended use

• Only use the device to determine the pH value and temperature of liquids in aquaria, ponds, swimming pools or in food.
• To use the device for its intended use, only use accessories and spare parts which have been approved by Trotec.

Foreseeable misuse

• Do not use the device in potentially explosive atmospheres or for measurements at live parts.
• The device is not designed to be used under laboratory conditions.
• Trotec accepts no liability for damages resulting from improper use. In such a case, any warranty claims will be voided. Any unauthorised modifications, alterations or structural changes to the device are forbidden.

Personnel qualifications
People who use this device must:

• be aware of the dangers that occur when handling corrosive liquids such as bases and acids.
• have read and understood the operating manual, especially the Safety chapter.

Residual risks

Warning of electrical voltage

• There is a risk of a short circuit due to liquids penetrating the housing!
• Do not immerse the device and the accessories in water. Make sure that no water or other liquids can enter the housing.

Warning of electrical voltage
Work on the electrical components must only be carried out by an authorized specialist company!

• Warning
  Be careful when handling strong acids or bases!
  If you are unsure whether or not a liquid has a corrosive effect, wear suitable protective equipment consisting of eye protection, protective clothing, protective gloves and safety boots in any case.

• Warning
  Risk of suffocation!
  Do not leave the packaging lying around. Children may use it as a dangerous toy.

• Warning
  The device is not a toy and does not belong in the hands of children.

• Warning
  Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way!Observe the personnel qualifications!

• Caution

  • Sodium carbonate (Na2CO3, contained in buffer solution 10.01) may cause eye irritation. Upon contact with eyes, thoroughly rinse with water and seek medical advice.
  • Keep sodium carbonate out of the reach of children. Do not breathe dust containing sodium carbonate.

• Caution
  Keep a sufficient distance from heat sources.

• Note
  To prevent damages to the device, do not expose it to extreme temperatures, extreme humidity or moisture.

• Note
  Do not use abrasive cleaners or solvents to clean the device.

Information about the device

Device description
The pH measuring device BW10 is suited for measuring pH values and temperatures of liquids. With the automatic temperature compensation and the automatic calibration functions the measuring device permits a quick and precise determination of the pH value between pH 0 and pH 14 in the temperature measuring range between 0 and 50 °C.

• The three-point calibration is already carried out before leaving the factory, but it can also be repeated using the supplied pH buffer solution set.
• The determined pH value is displayed along with the water temperature.
• The device comes equipped with an exchangeable pH electrode. The electrode and the water temperature probe are protected from external influences by means of a removable protective cap.
• The device is further equipped with a Hold function for holding the currently measured value.

Device depiction

Display

Technical data

with <85 % RH

Storage conditions| 10 °C to 25 °C with <65 % RH
Power supply| 4 x 1.5 V, LR44
Dimensions| 188 mm x 38 mm x 38 mm
Weight| 83 g

Scope of delivery

• 1 x pH measuring device
• 4 x 1.5 V LR44 batteries
• 1 x pH buffer solution set (4.01/7.00/10.01)
• 1 x Quick guide

Transport and storage

Note

• If you store or transport the device improperly, the device may be damaged.
• Note the information regarding transport and storage of the device.

Transport

• For transporting the device use a suitable bag to protect it from external influences.
• Make sure that the protective cap is attached to the measuring probe.

Storage
When the device is not being used, observe the following storage conditions:

• dry and protected from frost and heat
• protected from dust and direct sunlight
• with a cover to protect it from invasive dust if necessary
• the storage temperature complies with the values specified in the Technical data
• Remove the batteries from the device.

Operation

Inserting the batteries
Insert the supplied batteries into the device before first use.

Note
Make sure that the surface of the device is dry and the device is switched off.

1. Open the battery compartment at the top by unscrewing the lid.
2. Insert the batteries (4 x LR44 button cells) into the battery compartment with correct polarity.
3. Screw the lid back on the battery compartment. In doing so, make sure that the rubber seal is properly seated.

Removing the protective cap
The device has already been calibrated at the factory using a highly concentrated saline solution. This often leads to the formation of salt crystals at the diaphragm electrode (fibre bundle) during later usage. These visible residues are completely normal for pH-measuring electrodes of this type. Such residues are harmless for the measuring electrode and can easily be washed off with water; thus they do not represent any quality defect!

The measuring electrode is protected from external influences by means of a protective cap.

1. Prior to every measurement pull the protective cap off the measuring electrode.
2. After every measurement put the protective cap back on the electrode.

Performing calibration

Info
Before calibration immerse the measuring probe in distilled water for approx. 10 to 15 min.

To perform a calibration of the pH measuring device, you first have to prepare the buffer solutions contained in the supplied set. The buffer solutions correspond to the pH values 4 (red), 7 (green) and 10 (blue) with an accuracy of ±0.01 pH (at 25 °C).

Please proceed as follows to prepare a buffer solution:

Caution
The powder for the buffer solutions as well as the buffer solutions made thereof are unfit for human consumption.

Caution

• Sodium carbonate (Na2CO3, contained in buffer solution 10.01) may cause eye irritation. Upon contact with eyes, thoroughly rinse with water and seek medical advice.
• Keep sodium carbonate out of the reach of children. Do not breathe dust containing sodium carbonate.

1. Fill the contents of a sachet (e.g. pH 7 = green) into a beaker glass or suitable glass vessel with a capacity of at least 250 ml.
2. Add 250 ml of distilled water.
3. Stir the solution with a glass rob until the powder is completely dissolved.

Please note that the pH value of the buffer solution may vary depending on the temperature. The table below indicates the pH value as a function of the temperature (see also imprint on plastic sachets):

To perform the calibration, please proceed as follows:

Info
Always use fresh buffer solutions for calibration.

1. Press the Power button (5) to switch the device on.
   • The currently measured pH and temperature values are displayed.
2. With light circular motions, immerse the measuring probe in the buffer solution for the pH value 7 first.
   • The measuring electrode should be completely surrounded by the buffer solution.
3. Wait until a stable measured value is shown on the measurement value display (10).
4. Press the CAL button (3) for approx. 3 s.
   • CAL is displayed in the measurement value display (10).
5. Let go of the CAL button (3).
   • After approx. 2 s, SA is displayed in the measurement value display (10).
   • Afterwards, End is displayed.
   • Calibration for pH value 7 is now completed and the current measurement result is displayed.
6. Repeat steps 2 to 5 for the buffer solution which is closest to the expected pH value.

Info
If calibration is aborted, this is either due to a wrong buffer solution or to a defective measuring electrode. First check whether the correct buffer solution was used by means of a second measuring device if necessary. If the buffer solution corresponds to the pH value to be calibrated, the measuring electrode is defective and must be replaced, see chapter Replacing the measuring electrode.

Carrying out a measurement

1. Immerse the measuring probe in the liquid to be measured.
   • The measuring electrode should be completely surrounded by the liquid.
2. Press the Power button (5) to switch the device on.
   • The currently measured pH and temperature values are displayed.

Info

• If the measured value is outside the measuring range, this is indicated on the display.
• The measurement value display will show — for the pH value and either L or H for too-low or too-high-temperature values.

Changing the unit °C / °F
In the default setting, the measuring device is set to °C.

Please proceed as follows to change between the units °C and:

• The measuring device is switched off.

1. Simultaneously press the CAL (3) and Power button (5) until the unit °C (11) or °F (13) is displayed.
2. Press the CAL button (3) to switch between °C and °F.
3. Press the HOLD button (4) to save the setting.
   • SA appears on the display.
   • The setting is saved and the current measurement result is displayed.

Holding a measured value (HOLD)

1. Press the HOLD button (4) to freeze the currently measured value.
2. Press the HOLD button (4) again to show the currently measured values again.

Switching the device off
The device comes equipped with an automatic switch-off function and switches off automatically if no button was pressed for approx. 15 min.

1. Press the Power button (5) to switch the device off.

Maintenance and repair

Battery change
A battery change is required when the device can no longer be switched on (see chapter Inserting the battery).

Replacing the measuring electrode
The measuring electrode must be replaced if it is damaged or can no longer be properly calibrated. This manifests itself in the fact that calibration is aborted despite using the correct buffer solution.

1. Pull the protective cap off the measuring electrode.
2. Loosen the screwing at the measuring electrode and slide it downwards.
3. Pull the measuring electrode and the seal ring off the device.
4. Place the new seal ring onto the new measuring electrode.
5. Put the new measuring electrode on the device. In doing so, pay attention to the guide rails and connections.
6. Put the screwing back on and tighten it firmly.
7. Calibrate the device with the new measuring electrode, see chapter Operation.

Cleaning

Clean the device with a soft, damp, and lint-free cloth. Make sure that no moisture enters the housing. Do not use any sprays, solvents, alcohol-based cleaning agents or abrasive cleaners, but only clean water to moisten the cloth.

Cleaning the measuring probe
When cleaning the measuring probe, proceed with great caution:

• Rinse the electrode with distilled water.
• Avoid unnecessary friction/contact with the glass ball electrode as it may be damaged or age faster.

Repair
Do not modify the device or install any spare parts. For repairs or device testing, contact the manufacturer.

Disposal

Always dispose of packing materials in an environmentally friendly manner and in accordance with the applicable local disposal regulations. The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment must not be disposed of with the household waste at the end of its life. You will find collection points for free return of waste electrical and electronic equipment in your vicinity. The addresses can be obtained from your municipality or local administration. You can also find out about other return options that apply to many EU countries on the website https://hub.trotec.com/?id=45090. Otherwise, please contact an official recycling center for electronic and electrical equipment authorized for your country.

The separate collection of waste electrical and electronic equipment aims to enable the re-use, recycling, and other forms of recovery of waste equipment as well as to prevent negative effects on the environment and human health caused by the disposal of hazardous substances potentially contained in the equipment. In the European Union, batteries and accumulators must not be treated as domestic waste but must be disposed of professionally in accordance with Directive 2006/66/EC of the European Parliament and of the Council of 6 September 2006 on batteries and accumulators. Please dispose of batteries and accumulators according to the relevant legal requirements.

Only for the United Kingdom
According to Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), devices that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

Trotec GmbH

• Grebbener Str. 7 D-52525 Heinsberg
• +49 2452 962-400
• +49 2452 962-200
• info@trotec.com
• www.trotec.com.

References

• WEEE-Annahmestellen | Interzero - zero waste solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>