hansgrohe Pulsify 260 2jet Eco 24151XXX Overhead Shower Instruction Manual
- June 12, 2024
- hansgrohe
Table of Contents
- hansgrohe Pulsify 260 2jet Eco 24151XXX Overhead Shower
- Product Information
- Product Usage Instructions
- Troubleshooting
- Safety Notes
- Installation Instructions
- Technical Data
- Symbol description
- Assembly
- Test Certificate
- Spare Parts
- Special Accessories
- Installation Instruction
- Dimension
- Flow Diagram
- Cleaning
- Operation
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
hansgrohe Pulsify 260 2jet Eco 24151XXX Overhead Shower
Product Information
The product is a Pulsify 260 2jet Eco shower system. It is designed for bathing, hygienic, and body cleaning purposes. The shower head has a maximum operating pressure of 0.6 MPa. The recommended operating pressure for model 24151XXX is 0.16 – 0.4 MPa, and for model 24351XXX is 0.13 – 0.4 MPa. The product is suitable for use with hot and cold water. It is important to note that the product is exclusively designed for drinking water.
Technical Specifications
- Operating Pressure: max. 0.6 MPa
- Recommended Operating Pressure (24151XXX): 0.16 – 0.4 MPa
- Recommended Operating Pressure (24351XXX): 0.13 – 0.4 MPa
- Hot Water Temperature:
Product Usage Instructions
Installation Instructions
- Wear gloves during installation to prevent crushing and cutting injuries.
- Ensure that the wall is reinforced in the area where the shower system will be installed.
- Follow the provided installation example for proper installation.
Cleaning Instructions
To clean the shower head, follow these steps:
- Ensure that the shower head is not connected to the water supply.
- Remove any dirt or limescale buildup from the shower head.
- Clean the shower head using a suitable cleaning agent.
- Rinse the shower head thoroughly with water to remove any residue.
Operation Instructions
To use the shower system:
- Ensure that the water supply is connected to the shower system.
- Adjust the temperature and flow rate using the controls on the shower system.
- Enjoy your shower!
Troubleshooting
If the head shower is extremely leaky, it may be due to dirt or scale buildup. To remedy this, clean and descale the head shower as instructed in the cleaning instructions.
Safety Notes
- Gloves should be worn during installation to prevent crushing and cutting injuries.
- The product may only be used for bathing, hygienic and body cleaning purposes.
- The arm of the shower head is intended only to hold the shower head. Do not load it down with other objects!
Installation Instructions
- Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured.
- The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
- The plumbing codes applicable in the respective countries must be observed.
- During installation of the product by qualified trained personnel, make sure that the entire fastening surface is even and smooth (no protruding seams or tile offset), that the finish of the wall is suitable to apply the product and has no weak points.
- The mesh washers must be installed to protect against incoming dirt by pipework. Incoming dirt can impair the function and/or lead to damages on functional parts of the fixture; Hansgrohe will not be held liable for resulting damages.
- The product is not designed to be used with steam baths!
Technical Data
- Operating pressure: max. 0,6 MPa
- 24151XXX Recommended operating pressure: 0,16 – 0,4 MPa
- 24351XXX Recommended operating pressure: 0,13 – 0,4 MPa (1 MPa = 10 bar = 147 PSI)
- Hot water temperature: max. 60°C
- Thermal disinfection: 70°C / 4 min
The product is exclusively designed for drinking water
Symbol description
- Do not use silicone containing acetic acid!
- Installation example
- The wall must be reinforced in this area.
- Warm water
- Cold water
- Dimensions
- Flow diagram
- Spare parts
- XXX = Colors
- 000 = Chrome Plated
- 670 = Matt Black
- 700 = Matt White
- Special accessories order as an extra)
- extension 25 mm #13595000
- levelling set 1° #95521000
- Cleaning
- Operation
- Test certificate
Fault : Cause : Remedy
- Head shower extremely leaky
- Head shower soiled / scaled
- Clean / descale head shower
Assembly
Test Certificate
Spare Parts
Special Accessories
Installation Instruction
Dimension
Flow Diagram
www.hansgrohe.com/cleaning-recommendation
Cleaning recommendation / Warranty / Contact
Cleaning
Just clean: simply rub over the spray nozzles to remove lime scale
Operation
Hansgrohe · Auestraße 5 – 9 · D-77761 Schiltach
Telefon +49 (0) 78 36/51-1282
Telefax +49 (0) 7836/511440
E-Mail: info@hansgrohe.com
Internet: www.hansgrohe.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>